Study guide
11.2 IMSA Cable Specifications, Cable Pulling, Acceptance Testing & As-Builts
IMSA Traffic Signal Senior Field Technician Level III Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Adaptive Signal Control Technology (ASCT) & Modern Systems
1.1 ASCT Architecture & Operational Principles 1.2 Model-Based vs. Rule-Based ASCT Algorithms 1.3 ASCT Detection Layout & System Health Monitoring 1.4 Central Traffic Management Systems (ATMS) & Architecture
2 Chapter 2: Connected Vehicles (V2X), ITS Integration & Emerging Technologies
2.1 Connected Vehicle V2X Architecture & the 5.9 GHz Safety Spectrum 2.2 Roadside Unit Installation, GNSS Timing & SCMS Security 2.3 SPaT and MAP Message Structure under SAE J2735 2.4 Controller-to-RSU Interface, CV Applications & MAP Field Verification 2.5 Preemption vs. Priority and Transit Signal Priority Strategies 2.6 TSP Detection Architectures, Conditional Priority & Freight Priority 2.7 Automated Traffic Signal Performance Measures (ATSPMs)
3 Chapter 3: MUTCD Signal Warrants & Justification Studies
3.1 Traffic Studies & Engineering Data Collection 3.2 Vehicular Volume Warrants (Warrants 1, 2, and 3) 3.3 Pedestrian, School Crossing, and Network Warrants (Warrants 4, 5, and 8) 3.4 Coordinated, Crash Experience, Grade Crossing, and PHB Warrants (Warrants 6, 7, and 9)
4 Chapter 4: MUTCD Signal Equipment, Display & Visibility Standards
4.1 Signal Face Arrangements & MUTCD Lens Sizing 4.2 LED Optics, Backplates & Optical Shielding 4.3 Number of Signal Faces, the 20-Degree Placement Envelope & Sight Distance 4.4 Signal Face Mounting Heights, Lateral Offset & Distance from the Stop Line 4.5 Flashing Yellow Arrow Operation & Yellow Trap Elimination 4.6 Pedestrian Signal Displays, Countdown Modules, Interval Timing & APS 4.7 Bicycle Signal Faces & MUTCD Flashing Operation
5 Chapter 5: Advanced Traffic Detection Technologies & Configuration
5.1 Video Image Detection & Microwave Radar Detection 5.2 Thermal, Acoustic & Magnetometer Detection Technologies 5.3 Inductive Loop Physics, Geometry & Conductor Standards 5.4 Multi-Loop Arrays, Lead-In Cable & Pull-Box Splicing 5.5 Detector Testing, Tuning, Megohmmeter Diagnostics & Troubleshooting
6 Chapter 6: Traffic Communications & Fiber Optic Networks
6.1 Optical Waveguide Physics, Fiber Types & OSP Cable Construction 6.2 Optical Connectors, Polish Geometries & Redundant ITS Ring Topologies 6.3 Fiber Splicing, Optical Testing & Link Loss Budgets 6.4 Managed Industrial Ethernet in Traffic Cabinets 6.5 Copper, Twisted-Pair & Wireless Communications Media
7 Chapter 7: Actuated Phasing, Ring-Barrier Structure & Dual-Ring Operations
7.1 NEMA Dual-Ring Phasing, Barriers & Phase Compatibility 7.2 Lead-Lag Left Turns, the Yellow Trap & Signal Overlaps 7.3 Actuated Phase Parameters, Minimum Green, Passage Time & Termination 7.4 Recall Modes, Volume-Density Control & Parameter Diagnostics 7.5 Yellow Change & Red Clearance Interval Kinematics 7.6 Dilemma Zones, Pedestrian Interval Equations & a Full Field Calculation
8 Chapter 8: Coordinated Arterial Timing & Preemption Systems
8.1 Arterial Progression Principles & Actuated-Coordinated Operation 8.2 Time-Space Diagrams, Lead-Lag Sequencing & Transition Troubleshooting 8.3 Emergency Vehicle Preemption Technologies & Execution Sequence 8.4 Railroad Preemption Interconnects & Warning Time Calculations
9 Chapter 9: Electrical Codes, Grounding, Surge Protection & Power Distribution
9.1 NEC Articles, Underground Cover & Raceway Fill 9.2 Conductor Ampacity, Derating & NESC Overhead Clearances 9.3 Grounding, Bonding & Ground Resistance Testing 9.4 Transient Overvoltage, Surge Protective Devices & Cabinet Lightning Protection 9.5 Battery Backup Systems, Battery Chemistries & AC Branch Circuit Voltage Drop 9.6 Basic Electrical & Electronic Fundamentals for Signal Technicians
10 Chapter 10: NEMA TS1, TS2 & ATC Cabinet Architecture
10.1 NEMA TS1 vs. TS2 Architecture, SDLC Bus & BIUs 10.2 Malfunction Management Units (MMU) vs. Conflict Monitors (CMU) 10.3 Model 170/2070, ATC Architecture, Load Switches & Flashers
11 Chapter 11: Project Oversight, Quality Assurance, Maintenance & Troubleshooting
11.1 Civil, Raceway & Pole Construction Inspection Milestones 11.2 IMSA Cable Specifications, Cable Pulling, Acceptance Testing & As-Builts 11.3 Systematic Cabinet Troubleshooting & Diagnostic Instrumentation 11.4 Electrical Safety, Arc Flash Protection & Work Zone Traffic Control
11.2 IMSA Cable Specifications, Cable Pulling, Acceptance Testing & As-Builts
Key Takeaways Explain This Topic AI
IMSA 19-1 multiconductor signal cable is for underground conduit, IMSA 20-1 carries an integral messenger for aerial span installations, IMSA 50-2 is shielded twisted-pair loop lead-in, and IMSA 51-5 or 51-3 is loop wire.
Cable pulling is limited by both maximum tension and sidewall bearing pressure in bends; exceeding either damages insulation invisibly and produces a failure months after acceptance.
The 30-day burn-in period exists to surface intermittent faults — marginal splices, water intrusion, and detector drift — that a one-day functional test cannot reveal.
As-built documentation with cabinet wiring, conductor schedules, loop locations, and the final timing sheet is what makes the intersection maintainable; an undocumented intersection costs the agency more over its life than the construction saved.
Last updated: September 2026
- 11.2 IMSA Cable Specifications, Cable Pulling, Acceptance Testing & As-Builts
- 1. IMSA Cable Specifications, Sizing & Pulling Physics
The International Municipal Signal Association (IMSA) publishes rigorous physical cable specifications engineered to endure extreme environmental conditions, chemical exposure, and high electrical stress. +---------------------------------------------------------------------------------------------------+
- | IMSA TRAFFIC SIGNAL CABLE SPECIFICATION MATRIX |
- +---------------------------------------------------------------------------------------------------+
- | Specification | Cable Type | Jacket Material | Primary Application |
- +---------------+--------------------------+---------------------+----------------------------------+
- | IMSA 19-1 | Multi-Conductor Signal | Polyethylene / PVC | Underground conduit systems |
- | IMSA 20-1 | Multi-Conductor Signal | Polyethylene | Aerial span-wire (Messenger wire)|
- | IMSA 50-2 | Shielded Twisted Pair | Polyethylene | Inductive loop detector lead-in |
- | IMSA 51-3 | Single Conductor Loop | Cross-Linked PE | Roadway sawcut loop wire |
- | IMSA 51-5 | Tube-in-Duct Loop Wire | XLPE in loose PVC | Advanced sawcut loop wire |
- +---------------------------------------------------------------------------------------------------+
- IMSA Signal Cable Types & Conductor Sizing
Signal conductors must be stranded copper (typically #14 AWG , 600V rated) conforming to IMSA standards:
IMSA 19-1: Multi-conductor cable featuring solid or stranded copper conductors insulated with high-density polyethylene, covered with an overall black polyvinyl chloride (PVC) outer jacket. Engineered specifically for pulling into underground conduit raceways.
IMSA 20-1: Multi-conductor cable featuring polyethylene insulation and an overall high-density polyethylene outer jacket extruded over an integral extra-high-strength (EHS) galvanized steel messenger wire (figure-8 cross-section). Engineered for overhead aerial span-wire installations subject to wind galloping and ice loading.
Conductor Allocations:
3-Conductor (#14 AWG): Pedestrian signal indications (Walk, Don't Walk, Neutral).
5-Conductor (#14 AWG): Standard 3-section vehicular signal heads (Red, Yellow, Green, Neutral, Ground/Spare).
7-Conductor (#14 AWG): 5-section protected/permissive heads, 4-section Flashing Yellow Arrow (FYA) heads, or overlaps requiring individual phase feeds.
12-Conductor & 20-Conductor (#14 AWG): Mast arm trunk feeds and home-run trunk lines running from the cabinet to main junction boxes.
Inductive Loop Cable: IMSA 50-2, 51-3 & 51-5
IMSA 50-2 (Shielded Lead-In Cable): Consists of 1 pair or 2 pairs of twisted stranded copper conductors (typically #14 or #12 AWG) wrapped in an overall aluminum/polyester foil shield with a continuous tinned copper drain wire. The twist pitch (typically 3 to 5 turns per foot) and foil shield eliminate electromagnetic crosstalk and 60 Hz hum induced by adjacent 120V signal conductors.
IMSA 51-3: Single-conductor copper wire insulated with rugged cross-linked thermoset polyethylene (XLPE), installed directly into roadway sawcuts and sealed with loop sealant.
IMSA 51-5 (Tube-in-Duct Loop Wire): High-performance loop wire consisting of an XLPE-insulated copper conductor loosely enclosed inside a continuous, flexible polyvinyl chloride or polyethylene protective tube. The loose outer tube allows the inner conductor to move freely during asphalt thermal expansion and contraction, preventing cable snapping. It provides unmatched resistance to hot-pour rubberized asphalt sealants (applied at >350°F / 177°C) and chemical attack from petroleum oils and road salt.
Cable Pulling Mechanics, Tension Limits & Lubrication
Excessive pulling tension ruptures cable jackets, elongates copper conductors, strips insulation, and destroys raceways. Maximum Allowable Pulling Tension: T max = k ⋅ n ⋅ A = 0.008 × Σ C M \text{Maximum Allowable Pulling Tension: } T_{\text{max}} = k \cdot n \cdot A = 0.008 \times \Sigma CM Maximum Allowable Pulling Tension: T max = k ⋅ n ⋅ A = 0.008 × Σ CM
Where:
T_max = Maximum allowable pulling tension in pounds (lbs).
ΣCM = Total circular mil area of all copper conductors being pulled simultaneously (CM = 4,110 for #14 AWG).
0.008 = Tensile strength factor for soft-drawn copper (lbs/circular mil).
Field Example: Pulling two 7-conductor #14 AWG cables simultaneously (total of 14 copper conductors): T max = 0.008 × ( 14 × 4 , 110 ) = 0.008 × 57 , 540 = 460.3 lbs T_{\text{max}} = 0.008 \times (14 \times 4,110) = 0.008 \times 57,540 = 460.3\text{ lbs} T max = 0.008 × ( 14 × 4 , 110 ) = 0.008 × 57 , 540 = 460.3 lbs
Sidewall Bearing Pressure (SWBP): When cables are pulled through a conduit bend, the tension pulls the cable tightly against the inner radius of the raceway: S W B P = T R SWBP = \frac{T}{R} S W BP = R T
Where T is pulling tension exiting the bend in pounds, and R is the raceway bend radius in feet. Under industry standards, SWBP must never exceed 300 lbs/ft for standard jacketed cables (or 500 lbs/ft for heavy thermoset jackets). Exceeding this crushing force crushes conductor insulation, causing hidden microscopic fault pinholes.
Pulling Lubricants: Technicians must continuously apply a listed, water-based polymer cable pulling lubricant . Cable lube reduces the dynamic coefficient of friction (μ) from roughly 0.55 down to 0.15 to 0.20 , slashing pulling tension by up to 70%. Strict Rule: Never use petroleum-based greases, soap, or vegetable oil, which chemically dissolve polyethylene jackets and harden into an immovable glue inside the raceway.
2. Field Acceptance, Pre-Turn-On QA & The 30-Day Burn-In Test
Transitioning a newly constructed intersection from construction status to active public operation is a high-liability milestone requiring rigorous verification. +-----------------------------------------------------------------------------------+
- | PRE-TURN-ON VERIFICATION CHECKLIST |
- +-----------------------------------------------------------------------------------+
- | [ ] | Signal Head Bagging: Breathable, opaque hoods intact; no exposed lenses. |
- | [ ] | MMU/CMU Certification: 100% automated tester pass; matrix card validated. |
- | [ ] | Ground Resistance: Fall-of-potential test verifies < 10.0 Ohms to earth. |
- | [ ] | Insulation Megger: 500V DC test verifies >= 50 Mega-Ohms on all conductors.|
- | [ ] | Phasing Dry-Run: Controller sequencing and load switches tested on dummy. |
- | [ ] | Preemption Verification: EVP optical / railroad supervised loop tested. |
- +-----------------------------------------------------------------------------------+
- Pre-Turn-On Inspection Protocols
Signal Head Bagging: From the moment signal heads are erected until the exact instant of turn-on, all vehicular and pedestrian heads must be covered with opaque, heavy-duty, breathable canvas or burlap hoods . Technicians must never use black plastic trash bags, which trap moisture, bake LED modules in solar heat, and shred in light winds, creating dangerous false signals for drivers.
Conflict Monitor Electronic Certification: Every Malfunction Management Unit (MMU2) or Conflict Monitor (CMU) must be bench-tested using a certified automated electronic tester (e.g., EDI or ATSI tester). The automated tester exercises all 16 channels, verifying conflict sensing, permissive diode matrices, red fail detection, dual indication sensing, clearance timing monitors (< 2.7 s yellow lockout), and AC line dropout thresholds. The printed test report must be signed, dated, and archived in the cabinet document drawer.
Ground Resistance Verification: The cabinet grounding electrode system must be tested using the three-point fall-of-potential method (IEEE 81) . While the National Electrical Code (NEC 250.53) permits up to 25 Ω, traffic signal agency specifications strictly mandate a ground resistance of less than 10.0 Ω (and target < 5.0 Ω) to safeguard electronics against lightning strikes.
Field Wiring Megohmmeter (Megger) Testing: All field conductors must undergo high-voltage insulation resistance testing using a calibrated megohmmeter applied at 500V DC between each conductor and earth ground (and between adjacent conductors). Acceptance criteria: minimum insulation resistance of ≥ 50 MΩ (new quality cables typically measure >100 to 1,000 MΩ; any conductor measuring <10 MΩ indicates moisture penetration or jacket rupture and must be replaced).
Dry-Run Phasing Test: The controller must be operated in active coordination/actuation on a cabinet dummy load panel with field wire terminals disconnected. All phase timings, yellow changes, red clearances, pedestrian intervals, detector actuations, and preemption inputs must be verified visually before powering field heads.
The 30-Day Operational Acceptance (Burn-In) Test
Once energized, the intersection enters the formal 30-day operational acceptance test :
Test Scope: The signal must run under live traffic for 30 consecutive calendar days without unscheduled flashing, technician intervention, hardware failure, or contractor-related malfunction.
Restart Rule: If any component failure, open neutral, defective load switch, failed detector, or field wiring short occurs due to contractor workmanship or equipment defect, the failure is recorded, the contractor must immediately remediate the defect, and the 30-day burn-in clock immediately resets back to Day 1 . The agency will not accept the intersection until a full, uninterrupted 30-day period is successfully completed.
Force Majeure Exception: Disruptions caused by external events beyond contractor control—such as regional commercial power outages, lightning strikes exceeding UL-rated surge protector capacities, or motor vehicle crashes destroying equipment—do not reset the clock; the test is paused during repairs and resumes from the day it stopped.
3. As-Built Documentation & Asset Management
A construction project is incomplete until comprehensive as-built records are delivered:
Redline Construction Drawings: Must document all field modifications, exact conduit routing, depth deviations, and utility crossings.
Sub-Meter GPS Coordinates: Accurate RTK GNSS coordinates for all pull boxes, signal poles, controller cabinets, and service disconnect pedestals.
Sequential Cable Foot Markers: Signal cables feature footage markers stamped into the outer jacket. Technicians must record these numbers at every pull box and cabinet entry. If an underground open or short occurs years later, maintenance technicians can use a Time Domain Reflectometer (TDR) and the footage stamps to locate the exact break under asphalt within inches without excavation.
Cabinet Documentation Packet: A weatherproof cabinet binder containing laminated phase diagrams, MMU programming matrices, detector channel assignment tables, emergency vehicle preemption plans, and the signed pre-turn-on checklist.