Study guide
7.3 Flagger Hand Signaling (STOP, SLOW, Proceed Signals via STOP/SLOW Paddle vs. Red Flag Emergency Procedures)
IMSA Work Zone Temporary Traffic Control Technician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Overview & MUTCD Part 6 Fundamentals
1.1 IMSA Work Zone Certification & Regulatory Basis 1.2 Fundamental Principles of Temporary Traffic Control (TTC) 1.3 Legal Authority, Liability, & MUTCD Headings
2 Chapter 2: Temporary Traffic Control Zone Components
2.1 The Advance Warning Area (Sign Spacing A/B/C Distances & Roadway Types) 2.2 The Transition Area (Taper Types: Merging, Shifting, Shoulder, Downstream) 2.3 The Activity Area (Longitudinal/Lateral Buffer Spaces, Work Space, Traffic Space) 2.4 The Termination Area (Downstream Tapers, Signage, & Teardown Sequences)
3 Chapter 3: Work Zone Speed Management & Taper Calculations
3.1 Taper Length Formulas 3.2 Device Spacing Rules in Tapers and Tangents 3.3 Work Zone Speed Limit Reductions & Urban vs. Rural Conditions
4 Chapter 4: Temporary Traffic Control Signage
4.1 Temporary Work Zone Signs (Colors, Shapes, Retroreflectivity, Roll-up vs. Rigid) 4.2 Portable Changeable Message Signs (PCMS) & Arrow Boards (Display Modes, Placement, & Messages) 4.3 Sign Mounting Heights, Portable Supports, & Crashworthiness (NCHRP 350 / MASH)
5 Chapter 5: Channelizing & Delineation Devices
5.1 Cones, Tubular Markers, & Vertical Panels 5.2 Drums & Barricades 5.3 Longitudinal Channelizing Devices (LCDs), Temporary Pavement Markings, & Raised Pavement Markers
6 Chapter 6: Positive Protection & Safety Hardware
6.1 Positive Protection Devices 6.2 Truck-Mounted Attenuators (TMAs) & Shadow Vehicles 6.3 Vehicle Warning Lights, ANSI/ISEA 107 Class 2/3 High-Visibility Apparel, & Worker PPE
7 Chapter 7: Flagging Operations — Principles & Positioning
7.1 Flagger Qualifications, Responsibilities, & High-Visibility Safety Equipment 7.2 Flagger Station Selection, Stopping Sight Distance, Flagger Advance Warning Signage, & Escape Paths 7.3 Flagger Hand Signaling (STOP, SLOW, Proceed Signals via STOP/SLOW Paddle vs. Red Flag Emergency Procedures)
8 Chapter 8: One-Lane, Two-Way Traffic Control & Coordination
8.1 One-Lane, Two-Way Control Methods 8.2 Temporary Traffic Control Signals & Automated Flagger Assistance Devices (AFADs) 8.3 Emergency Vehicle Pass-Through Protocols & Queue Management During Flagging
9 Chapter 9: Typical Applications (TA) — Stationary Operations
9.1 TA-1 to TA-16: Work on Shoulders & Lane Closures on Two-Lane Roads 9.2 Multilane & Expressway Lane Closures (TA-30 to TA-34) 9.3 Double Lane Closures, Lane Shifts, Intersection & Roundabout Work Zones (TA-21 to TA-27, TA-36, TA-37, TA-52 to TA-54)
10 Chapter 10: Mobile, Short-Duration, & Nighttime Operations
10.1 Mobile Operations (Continuous Movement, Slow-Moving Convoy, Shadow Vehicle Spacing, TA-17 & TA-35) 10.2 Short-Duration Work (Under 1 Hour) & Emergency Maintenance Setup Rules 10.3 Nighttime Temporary Traffic Control (Glare Control, Artificial Lighting Specs, & Retroreflectivity Requirements)
11 Chapter 11: Worker Safety, Positive Protection, & Accessibility
11.1 Worker Safety Measures & Positive Protection Selection Guidelines (23 CFR 630 Subpart K) 11.2 Pedestrian Accessibility (ADA Compliance, Continuous Detectable Pathways, & Audible Warnings) 11.3 Bicycle Accommodation & Detour Signing in TTC Zones
12 Chapter 12: Incident Management & Special Work Zone Environments
12.1 Traffic Incident Management (TIM) Zones 12.2 Utility & Municipal Maintenance Work Zones 12.3 Work Zone Inspection, Maintenance, & Log Keeping
13 Chapter 13: Traffic Control Theory, Capacity, & Queue Management
13.1 Traffic Flow Theory & Capacity Reduction in Work Zones 13.2 Queue Development, Shockwaves, & End-of-Queue Crash Mitigation 13.3 Temporary Traffic Control Plan (TTCP) Design & Inspection Workflows
7.3 Flagger Hand Signaling (STOP, SLOW, Proceed Signals via STOP/SLOW Paddle vs. Red Flag Emergency Procedures)
Key Takeaways Explain This Topic AI
The STOP/SLOW paddle is the primary, required hand-signaling device for standard flagging; red flags (minimum 24 in. square on an approximately 36 in. staff) are restricted to emergency situations.
To stop traffic: face traffic, extend STOP paddle horizontally away from body in right hand, and extend left hand upward with palm facing traffic at shoulder height.
To direct traffic to proceed: turn paddle face to SLOW, keep paddle stationary, and motion traffic forward with free (left) arm in a sweeping underhand motion—NEVER wave the paddle itself.
To slow traffic: display SLOW paddle face stationary and extend free hand horizontally with palm facing down, moving arm up and down in small pumping motions below shoulder level.
Emergency red flag procedures require holding the flag staff extended horizontally and stationary across the lane to stop traffic, and slowly waving the flag from shoulder level to straight down (arm never above horizontal, free hand down) to alert or slow traffic.
Last updated: July 2026
Section 7.3: Flagger Hand Signaling (STOP, SLOW, Proceed Signals via STOP/SLOW Paddle vs. Red Flag Emergency Procedures)
Standardized hand-signaling procedures ensure that approaching motorists across all jurisdictions immediately recognize and obey traffic control commands. Ambiguous, informal, or non-standard visual gestures confuse drivers, trigger emergency braking, cause severe rear-end collisions, or lead to errant vehicle penetrations into active construction work spaces. MUTCD Section 6D.05 details the exact physical postures, arm positions, and hand-signaling movements required for displaying STOP, SLOW, and PROCEED indications using the mandatory STOP/SLOW paddle, while Section 6D.03 specifies the flag itself and Section 6D.05 specifies flag signaling methods.
Primary Device Mandate: STOP/SLOW Paddle vs. Red Flag Restrictions
MUTCD Section 6D.02 (Guidance) states that the STOP/SLOW paddle should be the primary and preferred hand-signaling device , because it gives road users more positive guidance than red flags. Section 6D.05 (Standard) requires flaggers to use a STOP/SLOW paddle, a flag, or an AFAD — hand movements alone are prohibited in one-lane, two-way operations.
STOP/SLOW Paddle : Mandated for all standard daytime and nighttime flagging operations. Its rigid octagonal shape, standardized retroreflective colors, and clear textual messaging eliminate driver misinterpretation and provide an authoritative visual signal.
Red Flag Restrictions : Flags (red or fluorescent orange-red, a minimum of 24 inches square, securely fastened to a staff approximately 36 inches long, with the free edge weighted so the flag hangs vertically, and retroreflectorized when used at night) are ONLY authorized in one exceptional circumstance :
Emergency Situations : Immediate, unexpected traffic control events (e.g., severe motor vehicle crashes, downed power lines, flash flooding, or sudden roadway cave-ins) where STOP/SLOW paddles are not immediately accessible on-site.
(The 2009 MUTCD also allowed red flags in low-speed, low-volume situations; the 11th Edition removed that allowance — emergencies are now the only case.)
Using red flags for routine, planned work zone flagging operations is a direct violation of MUTCD standards.
- Standardized STOP/SLOW Paddle Hand Signals (MUTCD Section 6D.05)
- 1. TO STOP TRAFFIC
When stopping an approaching line of traffic:
Body Posture : Stand on the paved/unpaved shoulder or within the closed travel lane facing approaching traffic directly.
Paddle Position : Hold the STOP paddle stationary in the right hand with the arm extended horizontally away from the body. The paddle sign face ("STOP") must be perpendicular to the approaching travel lane. The bottom of the rigid support staff rests on the road surface or is held vertically.
Left Hand Signal : Hold the free arm with the palm of the hand above shoulder level toward approaching traffic. This delivers an unmistakable secondary "STOP" visual command directly to the driver.
Verification : Hold position until the lead vehicle comes to a complete stop. Maintain eye contact with the driver.
2. TO DIRECT STOPPED TRAFFIC TO PROCEED
Once traffic is safely stopped and the single-lane work zone corridor is completely clear of opposing traffic:
Transition Paddle : Turn the paddle face from STOP to SLOW facing the stopped vehicle queue. Keep the paddle staff stationary in the right hand.
Body Posture : Remain on the shoulder/closed lane in full view of the lead driver.
Left Arm Motion : Hold the SLOW paddle face toward road users in a stationary position with the arm extended horizontally away from the body, and motion with the free hand for road users to proceed. (The MUTCD does not prescribe a specific arm motion.)
CRITICAL PROHIBITION : The flagger MUST NEVER wave the STOP/SLOW paddle itself to direct traffic to proceed. Waving the paddle creates confusing visual flashes between the STOP and SLOW faces, which can trigger emergency braking or panic among trailing drivers.
3. TO SLOW TRAFFIC
When approaching traffic needs to reduce speed without coming to a complete stop:
Body Posture : Stand facing approaching traffic on the shoulder or closed lane.
Paddle Position : Display the SLOW face of the paddle stationary in the right hand, extended horizontally away from the body.
Left Hand Signal : MUTCD Section 6D.05 requires only that the flagger face road users with the SLOW paddle face aimed toward them in a stationary position, arm extended horizontally away from the body. As an Option, the flagger may further alert or slow traffic by motioning up and down with the free hand, palm down. The MUTCD specifies no height range for this motion.
Practice note : Keeping the free hand low when signaling to slow avoids confusion with the above-shoulder palm used for the STOP indication. (The MUTCD states this restriction only for flag signaling — Section 6D.05 requires the arm not be raised above horizontal and the free hand be kept down.)
Emergency Red Flag Hand Signals (MUTCD Section 6D.05)
When red flags are authorized during emergency situations, flaggers must execute specific, distinct flag movements:
Signal Indication Red Flag Motion & Body Posture Free Hand Signal
TO STOP TRAFFIC Face road users and extend the flag staff horizontally across the road users’ lane in a stationary position so that the full area of the flag hangs visibly below the staff. Hold the free arm with the palm of the hand above shoulder level toward approaching traffic.
TO SLOW TRAFFIC Face road users and slowly wave the flag in a sweeping motion of the extended arm from shoulder level to straight down , without raising the arm above a horizontal position. Keep the free hand down.
TO PROCEED Face road users with the flag and arm lowered from the view of the road users. Motion with the free hand for road users to proceed. Flags shall not be used to signal road users to proceed.
Note : Never use a red flag to wave traffic forward directly. The flag itself must be lowered to the flagger's side when giving a proceed command with the free hand.
One-Lane, Two-Way Traffic Control Methods & Coordination
On two-lane, two-way highway lane closures, single-lane alternating traffic control is required. MUTCD Section 6E.01 (Guidance) recommends alternate one-way movement via flagger control, a flag transfer, a pilot car, traffic control signals, or stop or yield control (Sections 6E.02 through 6E.06). The five field methods below map onto those provisions:
Dual Flagger Control (Visual Contact) : Two flaggers stationed at opposite ends of the single-lane section. Applicable only on short, straight sections (typically < 200 ft) where both flaggers have clear, unobstructed line-of-sight of each other.
Two-Way Radio Communication : Mandatory whenever sight lines between flaggers are obstructed by curves, hill crests, foliage, or distance (> 200 ft). Flaggers must verbally confirm that all vehicles have cleared the bottleneck before reversing traffic flow.
Flag Transfer / Official Car Method : A physical flag token or lead vehicle driver is passed back and forth to guarantee that only one direction of traffic occupies the single lane at a time.
Pilot Car Operations : A designated pilot vehicle featuring a rear sign ("PILOT CAR FOLLOW ME") leads vehicle queues through complex, lengthy, or changing work zone corridors.
Automated Flagger Assistance Devices (AFADs) : Remotely operated STOP/SLOW or Red/Yellow Lens AFAD devices (MUTCD Sections 6L.02 through 6L.04) that position flaggers out of the lane of traffic. MUTCD Section 6L.02 requires two flaggers with either AFAD method; a single flagger may operate two AFADs only if that flagger has an unobstructed view of the AFADs and of approaching traffic in both directions.
Handling Uncooperative or Errant Drivers
If an errant or distracted driver ignores advance warning signs and flagger signals:
Do Not Stand Ground : Never attempt to physically block an approaching vehicle with your body or paddle.
Execute Escape Plan : Immediately step or jump into your pre-planned escape path.
Warn Work Crew : Sound an emergency warning device (e.g., an air horn or loud whistle) to alert workers in the activity area of an incoming errant vehicle.
Report Vehicle : Note the vehicle license plate, make, model, color, and driver description, and report the incident immediately to the site supervisor and law enforcement.