Study guide

7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

Key Takeaways Explain This Topic AI

The CIL Mechanical syllabus names friction and its applications including rolling friction, belt-pulley, brakes, clutches, screw jack, wedge and vehicles as a single explicit bullet.

Rolling resistance arises from deformation of the contacting surfaces and is characterised by a coefficient of rolling resistance far smaller than that of sliding friction.

For a flat belt on the point of slipping, the ratio of tight-side to slack-side tension is e raised to the product of the friction coefficient and the angle of lap.

A V-belt multiplies the effective friction coefficient by the reciprocal of the sine of the half-groove angle, which is why V-belts transmit far more power than flat belts of the same size.

Last updated: August 2026

Rolling Friction

A wheel rolling without slipping still meets resistance, but its origin differs from sliding friction. Both wheel and surface deform slightly, so the normal reaction acts a small distance a a a ahead of the geometric contact point. Taking moments about the contact patch, the force required to maintain rolling is F = N a r F = \frac{N a}{r} F = r N a ​

where a a a is the coefficient of rolling resistance , carrying units of length, and r r r is the wheel radius. The dimensionless rolling resistance coefficient is then μ r = a / r \mu_r = a/r μ r ​ = a / r .

  • Contact Typical μ r \mu_r μ r ​
  • Steel wheel on steel rail 0.001 - 0.002
  • Truck tyre on concrete 0.006 - 0.01
  • Tyre on soft haul road 0.02 - 0.05

The practical consequence for a coal mine is direct: rolling resistance on a poorly maintained haul road can exceed that on a well-graded surface several times over, which is why haul-road maintenance is a first-order cost lever for dumper fleets. Note also that larger wheels reduce rolling resistance for a given a a a , which is one reason mine haulers use very large diameter tyres.

Rolling resistance is typically one to two orders of magnitude smaller than sliding friction — the reason the wheel is worth having at all.

Belt and Rope Friction

For a flexible belt wrapped around a pulley over an angle of lap θ \theta θ (in radians ), on the point of slipping: T 1 T 2 = e μ θ \frac{T_1}{T_2} = e^{\mu\theta} T 2 ​ T 1 ​ ​ = e μ θ

where T 1 T_1 T 1 ​ is the tight-side tension and T 2 T_2 T 2 ​ the slack-side tension. This exponential relation explains why a few extra turns of rope around a bollard hold an enormous load.

Power transmitted P = ( T 1 − T 2 ) v P = (T_1 - T_2)\,v P = ( T 1 ​ − T 2 ​ ) v

where v v v is the belt speed.

Centrifugal tension

At speed, the belt's own mass generates an additional tension in every part of the belt: T c = m v 2 T_c = m v^2 T c ​ = m v 2

with m m m the mass per unit length. Centrifugal tension adds to both sides equally, so it does not increase the power transmitted, but it does consume part of the allowable maximum tension. Including it, T 1 − T c T 2 − T c = e μ θ \frac{T_1 - T_c}{T_2 - T_c} = e^{\mu\theta} T 2 ​ − T c ​ T 1 ​ − T c ​ ​ = e μ θ

Condition for maximum power

Differentiating the power with respect to velocity and setting the result to zero gives the classical result T max ⁡ = 3 T c ⟹ v opt = T max ⁡ 3 m T_{\max} = 3T_c \quad\Longrightarrow\quad v_{\text{opt}} = \sqrt{\frac{T_{\max}}{3m}} T m a x ​ = 3 T c ​ ⟹ v opt ​ = 3 m T m a x ​ ​ ​

That is, maximum power is transmitted when the centrifugal tension equals one third of the maximum permissible tension. This is one of the most frequently examined single results in the whole friction bullet.

V-belts

For a V-belt seated in a groove of total included angle 2 β 2\beta 2 β , the wedging action increases the normal reaction, and the relation becomes T 1 T 2 = e μ θ / sin ⁡ β \frac{T_1}{T_2} = e^{\mu\theta/\sin\beta} T 2 ​ T 1 ​ ​ = e μ θ / s i n β

Since sin ⁡ β < 1 \sin\beta < 1 sin β < 1 , the effective friction coefficient μ ′ = μ / sin ⁡ β \mu' = \mu/\sin\beta μ ′ = μ / sin β is substantially larger. For a typical half-angle of 17 degrees, sin ⁡ β ≈ 0.292 \sin\beta \approx 0.292 sin β ≈ 0.292 , so the effective coefficient is over three times the flat-belt value.

Angle of lap

For an open belt drive between pulleys of radii r 1 r_1 r 1 ​ and r 2 r_2 r 2 ​ at centre distance C C C , the lap angle on the smaller pulley is θ = π − 2 sin ⁡ − 1 ⁣ ( r 1 − r 2 C ) \theta = \pi - 2\sin^{-1}\!\left(\frac{r_1 - r_2}{C}\right) θ = π − 2 sin − 1 ( C r 1 ​ − r 2 ​ ​ )

For a crossed belt drive, both pulleys share the same lap angle θ = π + 2 sin ⁡ − 1 ⁣ ( r 1 + r 2 C ) \theta = \pi + 2\sin^{-1}\!\left(\frac{r_1 + r_2}{C}\right) θ = π + 2 sin − 1 ( C r 1 ​ + r 2 ​ ​ )

A crossed belt therefore always has a larger lap and can transmit more power, at the cost of belt wear from rubbing at the crossover.

Brakes

A brake absorbs kinetic or potential energy through friction and dissipates it as heat.

Single block or shoe brake

For a block pressed against a drum of radius r r r with normal force N N N , the friction force is F = μ N F = \mu N F = μ N and the braking torque is T b = μ N r T_b = \mu N r T b ​ = μ N r

The key design consideration is whether the brake is self-energising . If the moment of the friction force about the lever pivot acts in the same sense as the applied effort, the friction assists the application, reducing the required effort. If the friction moment equals or exceeds the restoring moment, the brake becomes self-locking — it grips without any applied effort, which is dangerous in a service brake but desirable in a holding brake.

Band brake

A flexible band wrapped over the drum obeys the same belt-friction relation: T 1 T 2 = e μ θ , T b = ( T 1 − T 2 ) r \frac{T_1}{T_2} = e^{\mu\theta}, \qquad T_b = (T_1 - T_2)\,r T 2 ​ T 1 ​ ​ = e μ θ , T b ​ = ( T 1 ​ − T 2 ​ ) r

A simple band brake anchors one end to the frame; a differential band brake attaches both ends to the lever at different distances from the fulcrum and can be made strongly self-energising.

Heat considerations

Braking energy appears as heat, and brake capacity is often limited by temperature rather than torque. For a vehicle of mass M M M descending a gradient at constant speed, the power to be dissipated is P = M g v sin ⁡ α P = M g v \sin\alpha P = M gv sin α

On long descents in an opencast pit this is precisely why haul trucks use retarders — engine, hydraulic or electric — rather than relying on friction brakes, which would overheat.

Clutches

A clutch transmits torque between coaxial shafts through friction.

Single plate clutch

For an annular friction surface of outer radius R o R_o R o ​ and inner radius R i R_i R i ​ with axial force W W W :

Uniform pressure theory (new, rigid, well-supported linings): T = 2 3 μ W R o 3 − R i 3 R o 2 − R i 2 T = \frac{2}{3}\mu W\,\frac{R_o^3 - R_i^3}{R_o^2 - R_i^2} T = 3 2 ​ μ W R o 2 ​ − R i 2 ​ R o 3 ​ − R i 3 ​ ​

Uniform wear theory (worn-in linings, where p r pr p r is constant): T = 1 2 μ W ( R o + R i ) = μ W R m T = \frac{1}{2}\mu W\left(R_o + R_i\right) = \mu W R_m T = 2 1 ​ μ W ( R o ​ + R i ​ ) = μ W R m ​

Uniform wear always gives the lower torque, so it is the safer basis for design. The mean radius R m R_m R m ​ is simply the arithmetic mean of the two radii.

For a clutch with n n n pairs of contacting surfaces, multiply by n n n . A single plate clutch with friction material on both faces has n = 2 n = 2 n = 2 .

Cone clutch

A cone clutch of semi-cone angle α \alpha α gains the same wedging benefit as a V-belt: T = μ W R m sin ⁡ α T = \frac{\mu W R_m}{\sin\alpha} T = sin α μ W R m ​ ​

Vehicle Dynamics on a Gradient

The syllabus names vehicles explicitly. For a vehicle of mass M M M on a gradient of angle α \alpha α , moving at constant speed, the tractive effort required is F = M g sin ⁡ α + μ r M g cos ⁡ α + 1 2 ρ C d A v 2 F = Mg\sin\alpha + \mu_r Mg\cos\alpha + \tfrac{1}{2}\rho C_d A v^2 F = M g sin α + μ r ​ M g cos α + 2 1 ​ ρ C d ​ A v 2

the three terms being grade resistance, rolling resistance and aerodynamic drag. For a slow, heavy mine hauler the drag term is negligible and the first two dominate.

Limit of adhesion

Whatever the engine can deliver, tractive effort cannot exceed what friction at the tyres permits: F max ⁡ = μ W driven F_{\max} = \mu W_{\text{driven}} F m a x ​ = μ W driven ​

where W driven W_{\text{driven}} W driven ​ is the load carried by the driven wheels. This is why a fully loaded rear-dump truck climbs better than an empty one on a slippery haul road — more weight sits on the driving axle.

Maximum gradient without slipping

Setting tractive effort equal to the adhesion limit and neglecting drag, tan ⁡ α max ⁡ ≈ μ − μ r ≈ μ for small μ r \tan\alpha_{\max} \approx \mu - \mu_r \;\approx\; \mu \text{ for small } \mu_r tan α m a x ​ ≈ μ − μ r ​ ≈ μ for small μ r ​

so the steepest climbable gradient is governed essentially by the coefficient of adhesion between tyre and road.