Study guide

10.4 Design of Spur, Helical, Bevel & Worm Gears

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

10.4 Design of Spur, Helical, Bevel & Worm Gears

Key Takeaways Explain This Topic AI

Gears are named in the machine-element design bullet of the CIL Mechanical Paper-II syllabus, distinct from the kinematic treatment in Theory of Machines.

The Lewis equation treats a gear tooth as a cantilever of uniform strength and gives the beam strength as the product of allowable stress, face width, module and the Lewis form factor.

A gear pair is safe when the beam strength and the wear strength both exceed the dynamic load, and the weaker of the two governs the design.

In a steel-and-cast-iron pair the material with the smaller product of allowable stress and Lewis form factor is the weaker member and must be designed for.

Last updated: August 2026

Design Versus Kinematics

The Theory of Machines treatment of gearing answers what motion results : velocity ratio, interference, path of contact, contact ratio. Gear design answers a different question — will the tooth break, and will the surface wear out? The CIL Mechanical syllabus lists gears under both headings, and the exam draws on both.

A gear tooth can fail in two independent ways, and a competent design checks both:

  • Failure mode Cause Governed by
  • Tooth breakage Bending fatigue at the root fillet Beam strength
  • Surface destruction Pitting, scoring, abrasive wear Wear strength
  • Tangential Tooth Load

The starting point of every gear calculation is the tangential force transmitted at the pitch circle: P t = 2 T d = 60 × 10 6 ( kW ) π d n N P_t = \frac{2T}{d} = \frac{60\times10^{6}\,(\text{kW})}{\pi\,d\,n} \;\text{N} P t ​ = d 2 T ​ = π d n 60 × 1 0 6 ( kW ) ​ N

with d d d in mm and n n n in rev/min. A service factor C s C_s C s ​ accounts for shock from the prime mover and driven machine, so the design tangential load is P design = P t C s C v P_{\text{design}} = \frac{P_t\,C_s}{C_v} P design ​ = C v ​ P t ​ C s ​ ​

where C v C_v C v ​ is the velocity factor, discussed below. For a coal-handling drive with a heavy-shock crusher, C s C_s C s ​ may reach 1.75 or more; for a steady electric-motor-driven fan it is near 1.0.

The Lewis Equation: Beam Strength

Wilfred Lewis modelled the tooth as a cantilever of uniform strength , fixed at the root and loaded at the tip. Inscribing a parabola of uniform strength inside the tooth profile and applying simple bending theory gives S b = σ b b m Y \boxed{S_b = \sigma_b\,b\,m\,Y} S b ​ = σ b ​ b m Y ​

where σ b \sigma_b σ b ​ is the allowable bending stress, b b b the face width, m m m the module and Y Y Y the Lewis form factor .

The form factor depends on the number of teeth z z z and the pressure angle, and for a 20-degree full-depth involute is approximated by Y = π ( 0.154 − 0.912 z ) Y = \pi\left(0.154 - \frac{0.912}{z}\right) Y = π ( 0.154 − z 0.912 ​ )

  • Number of teeth z z z Y Y Y (20-degree full depth)
  • 18 0.308
  • 25 0.340
  • 35 0.364
  • 50 0.408
  • Rack 0.484

Y Y Y increases with the number of teeth , so a small pinion has the weaker tooth. This is the reason the pinion is usually made of the stronger material.

Which member is weaker?

Since beam strength is proportional to σ b Y \sigma_b Y σ b ​ Y and b b b and m m m are common to both gears in mesh, the weaker member is the one with the smaller product σ b Y \sigma_b Y σ b ​ Y . Design for that member.

A typical case: a steel pinion with σ b = 200 \sigma_b = 200 σ b ​ = 200 MPa and Y p = 0.308 Y_p = 0.308 Y p ​ = 0.308 gives σ b Y = 61.6 \sigma_b Y = 61.6 σ b ​ Y = 61.6 ; a cast-iron gear with σ b = 55 \sigma_b = 55 σ b ​ = 55 MPa and Y g = 0.408 Y_g = 0.408 Y g ​ = 0.408 gives 22.4 22.4 22.4 . The cast-iron gear is weaker despite having more teeth, and it governs.

Face width

Face width is conventionally taken as a multiple of module: b = ( 9 to 15 ) m b = (9 \text{ to } 15)\,m b = ( 9 to 15 ) m

with 10 m m m a common starting value. Too narrow a face wastes capacity; too wide risks uneven load distribution from shaft misalignment.

Dynamic Load

Real gears carry more than the static tangential load because of tooth errors, elastic deflection and inertia of the accelerating masses. Two approaches are standard.

Velocity factor (approximate) P d = P t C v P_d = \frac{P_t}{C_v} P d ​ = C v ​ P t ​ ​

  • Gear class Velocity factor C v C_v C v ​ Pitch line velocity
  • Ordinary cut 3 3 + v \dfrac{3}{3+v} 3 + v 3 ​ up to 10 m/s
  • Carefully cut 4.5 4.5 + v \dfrac{4.5}{4.5+v} 4.5 + v 4.5 ​ up to 15 m/s
  • Precision generated 6 6 + v \dfrac{6}{6+v} 6 + v 6 ​ up to 20 m/s
  • Precision, ground 5.6 5.6 + v \dfrac{5.6}{5.6+\sqrt{v}} 5.6 + v ​ 5.6 ​ above 20 m/s

Buckingham's equation (accurate) P d = P t + 21 v ( b C + P t ) 21 v + b C + P t P_d = P_t + \frac{21v\left(b\,C + P_t\right)}{21v + \sqrt{b\,C + P_t}} P d ​ = P t ​ + 21 v + b C + P t ​ ​ 21 v ( b C + P t ​ ) ​

where v v v is pitch line velocity in m/s, b b b the face width in mm and C C C the deformation factor depending on tooth error and material combination. The incremental dynamic load is the second term.

Wear Strength

Surface fatigue produces pitting long before the tooth breaks in many drives. Buckingham's wear strength is S w = d p b Q K S_w = d_p\,b\,Q\,K S w ​ = d p ​ b Q K

where d p d_p d p ​ is the pinion pitch diameter, and the ratio factor is Q = 2 z g z g + z p = 2 i i + 1 Q = \frac{2\,z_g}{z_g + z_p} = \frac{2i}{i+1} Q = z g ​ + z p ​ 2 z g ​ ​ = i + 1 2 i ​

The load-stress factor K K K derives from the Hertzian contact stress σ e s \sigma_{es} σ es ​ : K = σ e s 2 sin ⁡ ϕ 1.4 ( 1 E p + 1 E g ) K = \frac{\sigma_{es}^2\sin\phi}{1.4}\left(\frac{1}{E_p} + \frac{1}{E_g}\right) K = 1.4 σ es 2 ​ sin ϕ ​ ( E p ​ 1 ​ + E g ​ 1 ​ )

Note that K K K depends on the square of the allowable surface endurance stress, which in turn correlates with surface hardness. Doubling hardness therefore roughly quadruples wear capacity, which is why case-hardening and nitriding are the standard responses to a pitting problem.

The Design Criteria

A gear pair is satisfactory when both conditions hold: S b ≥ P d (no tooth breakage) S_b \geq P_d \quad \text{(no tooth breakage)} S b ​ ≥ P d ​ (no tooth breakage) S w ≥ P d (no surface pitting) S_w \geq P_d \quad \text{(no surface pitting)} S w ​ ≥ P d ​ (no surface pitting)

The factor of safety is S b / P d S_b/P_d S b ​ / P d ​ in bending and S w / P d S_w/P_d S w ​ / P d ​ in wear, and the lower of the two describes the drive.

If beam strength is deficient, increase the module or the face width, or use a stronger material. If wear strength is deficient, increase the surface hardness or the pinion diameter — increasing module alone helps far less, because S w S_w S w ​ does not contain m m m explicitly.

Worked Example

A spur pinion of 20 teeth, module 5 mm, face width 50 mm transmits power at 900 rev/min to a 60-tooth gear. Take σ b = 140 \sigma_b = 140 σ b ​ = 140 MPa for the pinion and Y = 0.32 Y = 0.32 Y = 0.32 .

Pitch diameter: d = m z = 5 × 20 = 100 d = mz = 5\times20 = 100 d = m z = 5 × 20 = 100 mm.

Pitch line velocity: v = π d n 60000 = π × 100 × 900 60000 = 4.71 m/s v = \frac{\pi d n}{60000} = \frac{\pi\times100\times900}{60000} = 4.71 \text{ m/s} v = 60000 π d n ​ = 60000 π × 100 × 900 ​ = 4.71 m/s

Beam strength: S b = σ b b m Y = 140 × 50 × 5 × 0.32 = 11200 N S_b = \sigma_b\,b\,m\,Y = 140\times50\times5\times0.32 = 11200 \text{ N} S b ​ = σ b ​ b m Y = 140 × 50 × 5 × 0.32 = 11200 N

Using the ordinary-cut velocity factor C v = 3 / ( 3 + 4.71 ) = 0.389 C_v = 3/(3+4.71) = 0.389 C v ​ = 3/ ( 3 + 4.71 ) = 0.389 , the permissible tangential load is P t = S b × C v = 11200 × 0.389 = 4357 N P_t = S_b \times C_v = 11200\times0.389 = 4357 \text{ N} P t ​ = S b ​ × C v ​ = 11200 × 0.389 = 4357 N

and the power transmitted is P = P t v = 4357 × 4.71 = 20.5 kW P = P_t\,v = 4357\times4.71 = 20.5 \text{ kW} P = P t ​ v = 4357 × 4.71 = 20.5 kW

  • Other Gear Types
  • Helical gears

Teeth are cut on a helix at angle α \alpha α , so engagement is gradual and running is quieter with a higher contact ratio. Two moduli must be distinguished: m n = m t cos ⁡ α m_n = m_t\cos\alpha m n ​ = m t ​ cos α

The Lewis equation uses the normal module and a form factor based on the virtual (formative) number of teeth: z v = z cos ⁡ 3 α z_v = \frac{z}{\cos^3\alpha} z v ​ = cos 3 α z ​

The penalty is an axial thrust P a = P t tan ⁡ α P_a = P_t\tan\alpha P a ​ = P t ​ tan α , which the bearings must carry. Double helical (herringbone) gears cancel this thrust by using two opposite helices.

Bevel gears

Used for intersecting shafts, normally at 90 degrees. The tooth section varies along its length, so the Lewis equation carries a correction: S b = σ b b m Y ( 1 − b L ) S_b = \sigma_b\,b\,m\,Y\left(1 - \frac{b}{L}\right) S b ​ = σ b ​ b m Y ( 1 − L b ​ )

where L L L is the cone distance. The form factor uses the virtual number of teeth z v = z / cos ⁡ γ z_v = z/\cos\gamma z v ​ = z / cos γ , with γ \gamma γ the pitch cone angle. Face width is limited to about L / 3 L/3 L /3 .

Worm gears

Used for non-intersecting perpendicular shafts and very high reduction ratios in a single stage — commonly 20:1 to 100:1. The action is predominantly sliding , so efficiency is comparatively low and heat dissipation usually governs the design rather than tooth strength. Efficiency is η = tan ⁡ λ ( 1 − μ tan ⁡ λ ) tan ⁡ λ + μ \eta = \frac{\tan\lambda\,(1 - \mu\tan\lambda)}{\tan\lambda + \mu} η = tan λ + μ tan λ ( 1 − μ tan λ ) ​

where λ \lambda λ is the lead angle. When the lead angle is small enough that tan ⁡ λ < μ \tan\lambda < \mu tan λ < μ , the drive becomes self-locking — the worm can drive the wheel but the wheel cannot back-drive the worm. That property is exploited deliberately in hoists and lifting gear, where it prevents a load from running away.