Study guide

10.5 Design of Helical, Leaf & Torsion Springs

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

10.5 Design of Helical, Leaf & Torsion Springs

Key Takeaways Explain This Topic AI

Springs are named in the machine-element design bullet of the CIL Mechanical Paper-II syllabus.

The stiffness of a close-coiled helical compression spring equals Gd to the fourth divided by 8D cubed n, so wire diameter is by far the most sensitive parameter.

Wahl's factor corrects the maximum shear stress for both the direct shear component and the curvature of the wire, and it is always greater than one.

Springs in series share the same load and their compliances add, whereas springs in parallel share the same deflection and their stiffnesses add.

Last updated: August 2026

Why Springs Are a Torsion Problem

A close-coiled helical spring looks as if it should be analysed in bending, but it is not. When an axial load W W W is applied to a coil of mean diameter D D D , the load acts at a radius D / 2 D/2 D /2 from the wire axis, applying a torque to the wire: T = W D 2 T = \frac{WD}{2} T = 2 W D ​

The wire therefore carries torsional shear , and the design follows directly from the torsion formula for a circular section.

Shear Stress

Applying τ = 16 T / π d 3 \tau = 16T/\pi d^3 τ = 16 T / π d 3 with the torque above gives the uncorrected shear stress: τ = 16 T π d 3 = 8 W D π d 3 \tau = \frac{16T}{\pi d^3} = \frac{8WD}{\pi d^3} τ = π d 3 16 T ​ = π d 3 8 W D ​

This expression neglects two real effects:

Direct shear. The load W W W also produces a direct transverse shear over the wire cross-section.

Curvature. The inner fibre of the coil has a shorter length than the outer, concentrating stress at the inside of the coil .

Both are captured by the Wahl correction factor : K w = 4 C − 1 4 C − 4 + 0.615 C K_w = \frac{4C - 1}{4C - 4} + \frac{0.615}{C} K w ​ = 4 C − 4 4 C − 1 ​ + C 0.615 ​

where C = D / d C = D/d C = D / d is the spring index . The corrected maximum shear stress, occurring at the inner surface of the coil , is τ max ⁡ = K w 8 W D π d 3 \boxed{\tau_{\max} = K_w\,\frac{8WD}{\pi d^3}} τ m a x ​ = K w ​ π d 3 8 W D ​ ​

In the Wahl factor, the first term accounts for curvature and the second for direct shear.

Spring index C = D d C = \frac{D}{d} C = d D ​

  • Index C C C Consequence
  • Below 4 Severe curvature stress; difficult to coil
  • 4 to 12 Normal design range , with 6 to 9 preferred
  • Above 12 Prone to buckling and tangling; needs support

Because K w K_w K w ​ falls as C C C rises, a low spring index means a large stress correction — a spring index of 4 gives K w ≈ 1.40 K_w \approx 1.40 K w ​ ≈ 1.40 , while an index of 10 gives only 1.14 1.14 1.14 .

Deflection and Stiffness

Applying the angle-of-twist relation over the developed wire length π D n \pi D n π D n , where n n n is the number of active coils: δ = 8 W D 3 n G d 4 \boxed{\delta = \frac{8WD^3 n}{G d^4}} δ = G d 4 8 W D 3 n ​ ​

So the spring rate or stiffness is k = W δ = G d 4 8 D 3 n k = \frac{W}{\delta} = \frac{G d^4}{8 D^3 n} k = δ W ​ = 8 D 3 n G d 4 ​

The sensitivity to wire diameter

Stiffness varies with the fourth power of wire diameter and inversely with the cube of coil diameter. A 10% increase in wire diameter raises stiffness by about 46%; a 10% increase in coil diameter reduces it by about 25%. When a spring is too soft, changing the wire gauge is far more effective than any other adjustment.

Strain energy U = 1 2 W δ = 1 2 k δ 2 U = \tfrac{1}{2}W\delta = \tfrac{1}{2}k\delta^2 U = 2 1 ​ W δ = 2 1 ​ k δ 2

This is the energy a spring stores and returns, and it is what makes springs useful as shock absorbers and energy accumulators.

Combinations of Springs

Arrangement Shared quantity Equivalent stiffness

Series Same load through each 1 k e = 1 k 1 + 1 k 2 \dfrac{1}{k_e} = \dfrac{1}{k_1} + \dfrac{1}{k_2} k e ​ 1 ​ = k 1 ​ 1 ​ + k 2 ​ 1 ​

Parallel Same deflection in each k e = k 1 + k 2 k_e = k_1 + k_2 k e ​ = k 1 ​ + k 2 ​

Series springs are softer than either individual spring; parallel springs are stiffer than either. Two identical springs of stiffness k k k give k / 2 k/2 k /2 in series and 2 k 2k 2 k in parallel.

A useful check on which case applies: if the springs are joined end to end so the same force passes through both, they are in series. If both are compressed between the same two plates, they are in parallel — including the common concentric arrangement of a small spring nested inside a larger one.

Ends, Coils and Solid Length

  • End type Total coils n t n_t n t ​ Solid length Free length
  • Plain n n n ( n + 1 ) d (n+1)d ( n + 1 ) d p n + d p\,n + d p n + d
  • Plain and ground n + 1 n + 1 n + 1 n d n\,d n d p n p\,n p n
  • Squared n + 2 n + 2 n + 2 ( n + 3 ) d (n+3)d ( n + 3 ) d p n + 3 d p\,n + 3d p n + 3 d
  • Squared and ground n + 2 n + 2 n + 2 ( n + 2 ) d (n+2)d ( n + 2 ) d p n + 2 d p\,n + 2d p n + 2 d

Squared and ground ends are standard for compression springs because they seat squarely and apply load along the axis without inducing bending. Solid length is the compressed length when all coils touch, and the free length must exceed the solid length by the maximum working deflection plus a clash allowance of about 15%.

  • Buckling and Surge
  • Buckling

A compression spring behaves like a column and buckles when it is too slender. The governing ratio is the free length to mean coil diameter :

  • L f / D L_f / D L f ​ / D Behaviour
  • Below about 2.6 (both ends fixed) Stable
  • Above about 5.2 Buckling likely; guide the spring on a rod or inside a tube
  • Surge

When a spring is compressed rapidly, a wave of compression travels along the coils at the material's velocity of sound and reflects back. If the excitation frequency approaches the spring's natural frequency, surge occurs and stresses rise dramatically. The fundamental natural frequency of a spring with one end fixed is f n = 1 2 k g W s f_n = \frac{1}{2}\sqrt{\frac{k\,g}{W_s}} f n ​ = 2 1 ​ W s ​ k g ​ ​

where W s W_s W s ​ is the weight of the active coils. Design practice is to keep the natural frequency at least 15 to 20 times the operating frequency, which is why valve springs in high-speed engines use variable pitch or nested springs to break up the resonance.

Leaf Springs

A leaf spring is a bending element, unlike the helical spring. It comprises a stack of plates of decreasing length, approximating a beam of uniform strength — the classic diamond-shaped plate cut into strips and stacked.

For a semi-elliptical leaf spring of span 2 L 2L 2 L , width b b b , thickness t t t and n n n leaves, carrying a central load 2 W 2W 2 W : σ b = 6 W L n b t 2 , δ = 6 W L 3 n E b t 3 \sigma_b = \frac{6WL}{n b t^2}, \qquad \delta = \frac{6WL^3}{n E b t^3} σ b ​ = nb t 2 6 W L ​ , δ = n E b t 3 6 W L 3 ​

Leaves are classified as full length (the master leaf plus extra full-length leaves, carrying the eye) and graduated . Because the two groups deflect equally but have different stiffnesses, the full-length leaves carry a higher stress than the graduated ones: σ F = 18 W L b t 2 ( 3 n F + 2 n G ) , σ G = 12 W L b t 2 ( 3 n F + 2 n G ) \sigma_F = \frac{18WL}{bt^2(3n_F + 2n_G)}, \qquad \sigma_G = \frac{12WL}{bt^2(3n_F + 2n_G)} σ F ​ = b t 2 ( 3 n F ​ + 2 n G ​ ) 18 W L ​ , σ G ​ = b t 2 ( 3 n F ​ + 2 n G ​ ) 12 W L ​

so σ F = 1.5 σ G \sigma_F = 1.5\,\sigma_G σ F ​ = 1.5 σ G ​ . Nipping — pre-bending the graduated leaves to a smaller radius so that an initial gap exists — equalises the stresses and is standard practice in vehicle suspension design.

Torsion Springs

A helical torsion spring is loaded by a moment about its coil axis. Here the wire carries bending , not torsion — the opposite of the compression spring. For a spring of n n n coils: σ b = K 32 M π d 3 , θ = 64 M D n E d 4 \sigma_b = K\frac{32M}{\pi d^3}, \qquad \theta = \frac{64 M D n}{E d^4} σ b ​ = K π d 3 32 M ​ , θ = E d 4 64 M D n ​

where θ \theta θ is the angular deflection in radians and K K K a curvature correction.

Materials

  • Material Application
  • Hard-drawn spring steel wire General purpose, low cost
  • Oil-tempered carbon steel Higher duty springs
  • Chrome-vanadium steel Shock and fatigue loading, elevated temperature
  • Chrome-silicon steel High stress, high fatigue duty such as valve springs
  • Phosphor bronze, beryllium copper Corrosion resistance and electrical conductivity
  • Stainless steel Corrosive or high-temperature service

Springs are almost always fatigue-loaded, so surface finish matters enormously. Shot peening induces residual compressive stress at the surface and can raise fatigue life several-fold, and it is routine on vehicle suspension and valve springs.