Study guide

14.11 Principles of Work Holding, Jigs & Fixtures

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

14.11 Principles of Work Holding, Jigs & Fixtures

Key Takeaways Explain This Topic AI

Principles of work holding, jigs and fixtures are named explicitly in the Machining bullet of the CIL Mechanical Paper-II syllabus.

A jig both locates the workpiece and guides the cutting tool, whereas a fixture only locates and holds the work while the tool is guided by the machine.

A free rigid body has twelve degrees of freedom, and the 3-2-1 principle restrains nine of them using six locating points on three mutually perpendicular planes.

Locating must be complete but never redundant, since over-location makes the workpiece position indeterminate and introduces distortion.

Last updated: August 2026

Jig Versus Fixture

The distinction is the single most examined point in this topic.

  • Feature Jig Fixture
  • Locates the work Yes Yes
  • Holds the work Yes Yes
  • Guides the cutting tool Yes , through hardened bushes No
  • Fixed to the machine table Often not clamped down Usually bolted to the table
  • Typical use Drilling, reaming, tapping Milling, turning, grinding, welding, inspection
  • Weight Lighter Heavier and more rigid

The memory hook: a jig guides the tool; a fixture merely holds the work. A drill jig has hardened drill bushes that steer the drill to the exact position, so no marking out or centre punching is needed. A milling fixture has no such guidance, because the milling cutter's path is set by the machine's slides.

Why they exist

Both devices exist to transfer accuracy from a once-made tool to every part produced . The benefits are:

Interchangeability — parts are identical without individual measurement.

Reduced cycle time — no marking out, no individual setting.

Lower operator skill required , and therefore lower cost.

Improved safety , since the work is securely held.

Consistent quality independent of operator judgement.

The cost is the tooling itself, so jigs and fixtures are justified only by production volume .

Degrees of Freedom and the 3-2-1 Principle

A free rigid body in space has twelve degrees of freedom : along each of three axes it can translate in two directions, and about each axis it can rotate in two senses. That is 3 × 2 + 3 × 2 = 12 3\times2 + 3\times2 = 12 3 × 2 + 3 × 2 = 12 .

The 3-2-1 principle

The standard scheme for locating a prismatic workpiece uses six locating points arranged on three mutually perpendicular planes:

  • Plane Points Restrains
  • Primary (base) 3 points, not collinear Vertical translation downward and two rotations
  • Secondary (side) 2 points One horizontal translation and one rotation
  • Tertiary (end) 1 point The remaining horizontal translation

These six points restrain nine degrees of freedom. The remaining three — motion away from each of the three locating planes — are restrained by the clamping forces, not by the locators. This division between locating and clamping is the essential idea, and it is why clamps must always press the work against the locators.

Three points define a plane uniquely, which is why the primary plane uses exactly three: a fourth would be redundant and would rock.

Over-location

Locating must be complete but never redundant. If two features attempt to control the same degree of freedom, the workpiece position becomes indeterminate — it will seat against one or the other depending on tolerances — and clamping introduces distortion. Common over-location errors include using two full-round locating pins, or locating on both a face and a shoulder that control the same direction.

The standard remedy for two-pin location is to make the first pin round and the second a diamond pin , relieved on two sides. The round pin fixes position; the diamond pin fixes rotation only, without fighting the round pin over the centre distance tolerance.

Locating Devices

  • Device Application
  • Flat / plate locators Locating on a machined flat surface
  • Pin locators (round, conical, diamond) Locating from holes
  • V-block Self-centring location of cylindrical work
  • Vee locator, adjustable Cylindrical work of varying diameter
  • Nesting locators Cavity matching the part profile
  • Jack pins / adjustable supports Supporting unmachined or irregular surfaces
  • Design rules for locators

Locate from a machined surface wherever possible, and always from the same datum used in design and inspection. Mismatched datums between design, manufacture and inspection produce tolerance stack-up.

Make locators hardened, ground and replaceable , since they wear.

Position locators so that swarf cannot accumulate on them; provide relief grooves and chip clearance.

Make locating errors visible — the part should not fit at all if loaded incorrectly. This is foolproofing or poka-yoke , commonly achieved by adding an asymmetric pin that prevents loading the part the wrong way round.

Space locators as widely apart as the part allows, to minimise angular error.

Clamping Devices

  • Clamp Character
  • Strap / heel clamp Simple, versatile
  • Screw clamp High force, self-locking, slow
  • Cam clamp Fast acting; moderate force; may vibrate loose
  • Toggle clamp Very fast; goes over-centre and locks
  • Wedge clamp High mechanical advantage
  • Hydraulic / pneumatic Fast, uniform, remotely controlled; suits multiple clamping points
  • Magnetic Fast, unobstructed access; ferrous work only, as on a surface grinder
  • Vacuum Thin, flat, non-ferrous or non-metallic work
  • Design rules for clamping

Clamping force must act towards the locators , never away from them, so the work is pressed onto its location.

Clamp over a solid, supported part of the workpiece, ideally directly above a locator, so the force is not carried by an unsupported span.

Use the minimum force that resists the cutting forces — excess clamping distorts the part, and the distortion springs back after machining, leaving the finished dimension wrong.

Clamping must not obstruct loading, unloading, tool access, or chip and coolant flow.

Clamps should be quick-acting where cycle time matters, and should be captive so they cannot be lost.

The cutting forces should ideally act into the locators, so that the tool helps hold the work rather than lifting it.

Types of Jigs

  • Jig type Description
  • Template jig Simplest; a plate with holes laid over the work, no clamping
  • Plate jig Template with clamping added
  • Channel jig Channel-section body; work sits inside
  • Box (closed) jig Encloses the work; allows drilling from several faces without resetting
  • Leaf jig Hinged leaf carrying the bushes, for fast loading
  • Diameter / ring jig For drilling radially on round parts
  • Indexing jig Rotates the work through set angles for equally spaced holes
  • Trunnion jig Large or awkward work supported between trunnions and rotated
  • Drill bushes

The guiding element of a jig:

  • Bush Use
  • Press-fit Permanent, single operation
  • Renewable (slip) Removable for replacement or for a second tool such as a reamer following a drill
  • Liner (master) Permanently fitted, receives renewable bushes

Bush length is normally 1.5 to 2 times the hole diameter, and the clearance between bush and work is typically about one drill diameter, providing chip escape while retaining accurate guidance.

Types of Fixtures

  • Fixture Application
  • Milling fixture Bolted to the table; set relative to the cutter with a setting block and feeler gauge
  • Turning fixture Mounted on the spindle or faceplate; must be balanced
  • Grinding fixture High rigidity; often magnetic
  • Welding fixture Controls distortion during welding; heat-resistant
  • Assembly fixture Holds components in relation during assembly
  • Inspection fixture Holds the part in a repeatable position for measurement
  • Modular fixture Standard elements assembled on a gridded base plate; economical for small batches
  • Economic Justification

The decision to build a jig or fixture is an economic one. Given tooling cost C t C_t C t ​ , saving per part s s s and quantity N N N , tooling is justified when N s > C t N\,s > C_t N s > C t ​

so the break-even quantity is N = C t / s N = C_t/s N = C t ​ / s . For a small batch, modular fixturing — reusable standard elements assembled on a gridded base — is often the right answer, because the elements are recovered and reused rather than scrapped with the job. In a maintenance workshop of the kind found at a coal subsidiary, where batch sizes are small but repeat work is common, modular fixturing and simple plate jigs usually make more sense than dedicated tooling.