Study guide
14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM
Coal India Management Trainee CIL MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape
1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations
2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs
2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography
3 Chapter 3: Paper-I Reasoning & Logical Ability
3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning
4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude
4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude
5 Chapter 5: Paper-I General English & Verbal Ability
5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement
6 Chapter 6: Paper-II Engineering Mathematics
6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers
7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics
7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics
8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity
8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact
9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations
9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects
10 Chapter 10: Paper-II Machine Design & Failure Theories
10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat
11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery
11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy
12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery
12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams
13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning
13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics
14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology
14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation
15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree
14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM
Key Takeaways Explain This Topic AI
Principles of non-traditional machining processes are named explicitly in the Machining bullet of the CIL Mechanical Paper-II syllabus.
Electrical discharge machining removes metal by controlled sparks across a dielectric gap, so the tool never touches the work and only electrically conductive materials can be cut.
Electrochemical machining removes metal by anodic dissolution following Faraday's laws, causing no tool wear and no heat-affected zone.
Ultrasonic and abrasive jet machining are mechanical processes that suit hard and brittle non-conductive materials such as ceramics and glass.
Last updated: August 2026
Why Non-Traditional Processes Exist
Conventional machining removes metal by mechanical shear with a tool harder than the workpiece. That requirement fails in four situations, and each of them motivates a non-traditional process:
The workpiece is harder than any tool material — hardened die steel, tungsten carbide, ceramics.
The shape is impossible for a rotating or reciprocating tool — deep narrow slots, sharp internal corners, complex three-dimensional cavities.
The part is too fragile or thin to withstand cutting forces.
No heat-affected zone or residual stress is acceptable.
Classification by Energy Source
- Energy Processes
- Mechanical Ultrasonic machining (USM), abrasive jet (AJM), water jet (WJM), abrasive water jet (AWJM)
Electrical / chemical Electrochemical machining (ECM), electrochemical grinding (ECG), chemical machining (CHM)
Thermal Electrical discharge machining (EDM), wire EDM, laser beam (LBM), electron beam (EBM), plasma arc (PAM)
- Electrical Discharge Machining
- Mechanism
Tool and workpiece are separated by a small gap, typically 0.01 to 0.5 mm, flooded with a dielectric fluid — usually kerosene or a specialised EDM oil. A pulsed DC voltage builds until the dielectric breaks down and a spark jumps the smallest gap. Local temperature reaches many thousands of degrees, melting and vaporising a tiny crater of metal, which the flowing dielectric flushes away. Millions of such discharges per minute erode the shape.
Key characteristics
The tool never touches the work, so there is no cutting force . Delicate and thin sections can be machined.
The workpiece must be electrically conductive . This is the single most important limitation and the most frequently examined point.
Hardness is irrelevant — hardened tool steel machines as readily as annealed.
The tool (electrode) is usually copper, graphite or brass , and it does wear , so wear ratio matters.
The workpiece is normally the anode (positive) and the tool the cathode, because material removal is greater at the anode with the usual polarity.
A recast layer and a heat-affected zone are produced, and surface finish improves as spark energy is reduced, at the cost of removal rate.
The dielectric serves three purposes: it insulates until breakdown, it flushes debris from the gap, and it cools the electrode and workpiece.
Wire EDM
A continuously travelling wire, typically 0.05 to 0.30 mm brass or coated copper, replaces the shaped electrode and cuts a contour like a bandsaw. Because the wire is consumed continuously, wear does not accumulate. Wire EDM is the standard method for producing blanking dies and punches with sharp internal corners.
- Electrochemical Machining
- Mechanism
ECM is the reverse of electroplating. The workpiece is the anode , the shaped tool the cathode , and an electrolyte — typically sodium chloride or sodium nitrate solution — is pumped through the gap at high velocity. Applying a low voltage of 5 to 25 volts at very high current density causes anodic dissolution : metal atoms leave the workpiece as ions and are carried away as hydroxide sludge.
Material removal rate
Removal follows Faraday's laws of electrolysis : m = I t A w Z F m = \frac{I\,t\,A_w}{Z\,F} m = Z F I t A w
where I I I is current, t t t time, A w A_w A w atomic weight, Z Z Z valency and F F F the Faraday constant of 96,500 coulombs per mole. In volumetric terms, M R R = I A w ρ Z F MRR = \frac{I\,A_w}{\rho\,Z\,F} MRR = ρ Z F I A w
The removal rate depends only on the current and the material's electrochemical equivalent — not on the workpiece hardness at all.
Key characteristics
No tool wear , because the cathode is not consumed. This is ECM's decisive advantage over EDM.
No heat-affected zone, no residual stress, no burrs — the process is athermal.
No cutting force .
The workpiece must be conductive.
Sharp internal corners cannot be produced, because the field spreads. Corner radii are inherent.
Electrolyte is corrosive and the sludge requires disposal, so the plant is expensive.
Electrochemical grinding combines a conductive abrasive wheel with ECM action, with roughly 90% of removal electrochemical and 10% abrasive. It is used for sharpening carbide tools without the heat cracking that conventional grinding causes.
Ultrasonic Machining
A tool shaped to the required cavity vibrates axially at ultrasonic frequency, typically 20 kHz with an amplitude of 10 to 50 micrometres. An abrasive slurry — boron carbide, silicon carbide or aluminium oxide in water — flows between tool and work. The vibrating tool hammers the abrasive grains against the workpiece, chipping away microscopic fragments.
Key characteristics
Suits hard and brittle materials: glass, ceramics, quartz, germanium, hardened steel.
Does not require the workpiece to be conductive , which distinguishes it decisively from EDM and ECM.
Ductile materials machine poorly, because they absorb the impact plastically rather than fracturing.
The tool is a ductile material such as soft steel or brass, and it wears.
Removal rate is low, so it suits small precise features rather than bulk removal.
The transducer is magnetostrictive or piezoelectric , and a horn or velocity transformer amplifies the amplitude to a usable value.
Abrasive Jet and Water Jet Machining
Abrasive jet machining directs a high-velocity stream of gas, usually dry air or nitrogen at 200 to 400 m/s, carrying fine abrasive particles of 10 to 50 micrometres. Material is removed by erosion. AJM suits hard, brittle and heat-sensitive materials, and is used for cutting thin sections, deburring, cleaning and etching. Removal rates are very low.
Water jet machining uses a fine jet of water at 200 to 400 MPa, cutting soft materials such as plastics, rubber, textiles, food and composites with no heat and no dust. Abrasive water jet machining adds garnet abrasive to the stream and will cut steel, titanium and stone.
AWJM has genuine relevance in mining and heavy industry: it cuts thick plate without a heat-affected zone, and because it produces no spark it can be used in potentially explosive atmospheres where flame cutting or grinding would be prohibited.
- Laser and Electron Beam Machining
- Laser beam machining
A coherent monochromatic beam is focused to a spot of a few micrometres, producing power densities sufficient to melt and vaporise any material. Common industrial lasers are CO2 (10.6 micrometre wavelength, good for non-metals and thick steel) and Nd:YAG or fibre (1.06 micrometres, better absorbed by metals).
Characteristics: no tool contact, works on conductors and non-conductors alike , very small heat-affected zone, extremely fine holes and slots possible, easily automated. Limitations are high capital cost, low energy efficiency, a taper on deep holes, and reflectivity problems with copper, aluminium and gold at longer wavelengths.
Electron beam machining
A focused stream of high-velocity electrons converts kinetic energy to heat on impact. It requires a vacuum chamber , which is its principal practical limitation, but produces extremely high depth-to-diameter ratios — holes with aspect ratios of 100 to 1 are achievable. It also generates X-rays, requiring shielding.
Comparison Table
- Process Mechanism Conductive work needed Tool wear Heat affected zone
- EDM Thermal, spark erosion Yes Yes Yes
- Wire EDM Thermal, spark erosion Yes Continuous fresh wire Yes
- ECM Electrochemical dissolution Yes No No
- USM Mechanical, abrasive impact No Yes No
- AJM Mechanical, erosion No Nozzle wear No
- AWJM Mechanical, erosion No Nozzle wear No
- LBM Thermal, vaporisation No No Yes, small
- EBM Thermal, vaporisation No No Yes, small
- Selection Framework
- Requirement Process
- Complex cavity in hardened die steel EDM
- Sharp-cornered profile through a hardened plate Wire EDM
- Burr-free, stress-free machining of a turbine blade or awkward internal passage ECM
- Holes in glass, quartz or ceramic USM
- Thick plate cut with no heat-affected zone, or in an explosive atmosphere AWJM
- Very fine holes, high speed, non-metals included LBM
- Very high aspect-ratio holes, vacuum acceptable EBM
The practical decision usually starts with two questions: is the workpiece conductive , and is a heat-affected zone acceptable ? Those two answers alone narrow the field to two or three candidates.