Study guide

14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing

Key Takeaways Explain This Topic AI

Sheet metal forming operations of shearing, deep drawing and bending are named explicitly in the CIL Mechanical Paper-II syllabus.

In blanking the punched-out piece is the product, whereas in piercing the punched hole is the product and the removed slug is scrap.

Clearance is provided on the die in blanking and on the punch in piercing, so that the product retains the intended dimension in each case.

Spring-back after bending is elastic recovery, and it is compensated by over-bending, bottoming or coining rather than eliminated.

Last updated: August 2026

Shearing Operations

Shearing separates sheet metal by subjecting it to shear stress between a punch and a die until fracture propagates.

Blanking versus piercing

This distinction generates more objective items than any other point in the topic.

  • Operation The product is The scrap is Clearance is on the
  • Blanking The piece punched out The remaining strip Die
  • Piercing (punching) The hole produced The removed slug Punch

The reasoning behind the clearance rule follows from where the fracture surface forms. In blanking, the blank must match the die opening, so the die is made to size and the punch is made smaller by the clearance. In piercing, the hole must match the punch , so the punch is made to size and the die opening is made larger.

Other shearing operations

  • Operation Description
  • Notching Removes material from the edge of the strip
  • Perforating Punches many closely spaced holes
  • Trimming Removes excess material from a formed part
  • Slitting Cuts along a line without removing material
  • Lancing Cuts and bends without removing material, as for a louvre
  • Parting Separates a part by cutting on two sides
  • Cut edge quality

A sheared edge has four distinct zones from top to bottom: rollover , a smooth burnished band, a rough fracture zone, and a burr on the exit side. Correct clearance makes the fracture lines from punch and die meet cleanly. Too little clearance produces secondary shear and a ragged double burnish; too much produces excessive rollover and a large burr.

  • Clearance and force
  • Clearance per side is typically c = 0.0032 t τ c = 0.0032\,t\sqrt{\tau} c = 0.0032 t τ ​

with t t t in mm and τ \tau τ the shear strength in MPa, or as a practical rule 2 to 10% of thickness per side.

The cutting force is F = L t τ F = L\,t\,\tau F = L t τ

where L L L is the total length of the cut perimeter. For a circular blank of diameter d d d , L = π d L = \pi d L = π d .

Worked example. Blanking a 50 mm disc from 2 mm sheet with shear strength 300 MPa: F = π ( 50 ) ( 2 ) ( 300 ) = 94,248 N ≈ 94 kN F = \pi(50)(2)(300) = 94{,}248 \text{ N} \approx 94 \text{ kN} F = π ( 50 ) ( 2 ) ( 300 ) = 94 , 248 N ≈ 94 kN

Reducing the force

Press capacity is often the constraint, and two techniques reduce peak force:

Shear on the punch or die — grinding an angle so the cut is progressive rather than simultaneous. This reduces peak force but not the total work done.

Stepped punches in a multi-hole tool, so that the punches enter at different times.

  • Bending
  • Bend allowance

The length of the neutral axis through the bend determines the developed blank length: L b = θ ( R + k t ) L_b = \theta\left(R + k\,t\right) L b ​ = θ ( R + k t )

with θ \theta θ in radians, R R R the inside bend radius and k k k the location of the neutral axis, taken as 0.33 for R < 2 t R < 2t R < 2 t and 0.5 for R ≥ 2 t R \geq 2t R ≥ 2 t . The neutral axis shifts towards the inside surface for sharp bends because the compressed inner fibres are constrained.

Bending force

For V-bending in a die of opening W W W : F = k b f σ u t w t 2 W F = \frac{k_{bf}\,\sigma_{ut}\,w\,t^2}{W} F = W k b f ​ σ u t ​ w t 2 ​

with k b f k_{bf} k b f ​ about 1.33 for V-bending and 0.33 for edge (wiping) bending.

Spring-back

The outer fibres of a bend are in tension and the inner in compression, and both recover elastically when the load is released, so the bend opens out . The spring-back factor is K s = θ final θ die K_s = \frac{\theta_{\text{final}}}{\theta_{\text{die}}} K s ​ = θ die ​ θ final ​ ​

Spring-back is greater for higher yield strength, larger bend radius relative to thickness, and lower elastic modulus. Compensation methods:

Over-bending past the required angle by the anticipated recovery.

Bottoming , where the punch compresses the bend zone at the end of the stroke.

Coining , applying very high localised pressure to yield the material through the full thickness.

Stretch forming , applying tension so the whole section yields.

Minimum bend radius

Bending is limited by cracking of the outer fibres. The minimum radius, expressed as a multiple of thickness, correlates with the material's tensile reduction in area r r r : R min ⁡ t = 50 r − 1 \frac{R_{\min}}{t} = \frac{50}{r} - 1 t R m i n ​ ​ = r 50 ​ − 1

A material with 50% reduction in area can be bent to a radius equal to its thickness. Bending across the rolling direction is easier than along it, because the elongated grain structure makes the sheet anisotropic.

Deep Drawing

Deep drawing converts a flat blank into a cup or box. It is not a stretching operation — the material flows inward from the flange to form the wall, which is why the flange must be free to draw in.

The forces at work

  • Zone Stress state
  • Flange Radial tension , circumferential compression
  • Die radius Bending then unbending
  • Cup wall Longitudinal tension
  • Punch radius Bending, with the wall thinning slightly
  • Cup bottom Almost undeformed

The circumferential compression in the flange is what causes wrinkling , the characteristic deep-drawing failure. A blank holder suppresses it by clamping the flange. The blank holder force must be carefully set: too little and the flange wrinkles, too much and the flange cannot draw in, so the wall tears at the punch radius.

Limiting drawing ratio

The drawing ratio is D R = D blank D punch DR = \frac{D_{\text{blank}}}{D_{\text{punch}}} D R = D punch ​ D blank ​ ​

The wall must transmit the entire drawing force, so it fails once that force exceeds the wall's strength. This sets the limiting drawing ratio , theoretically e = 2.72 e = 2.72 e = 2.72 for a frictionless ideal, and practically about 2.0 for a single draw. Deeper cups require redrawing through successive smaller dies, with annealing between stages if cold work accumulates.

The percentage reduction is Reduction = D b − D p D b × 100 \text{Reduction} = \frac{D_b - D_p}{D_b}\times100 Reduction = D b ​ D b ​ − D p ​ ​ × 100

typically limited to about 50% on the first draw, 30% on the second and 16% on the third.

Drawing force F = π D p t σ u t ( D b D p − 0.7 ) F = \pi\,D_p\,t\,\sigma_{ut}\left(\frac{D_b}{D_p} - 0.7\right) F = π D p ​ t σ u t ​ ( D p ​ D b ​ ​ − 0.7 )

The blank holder force is typically about 30 to 40% of the drawing force.

Blank size

For a cylindrical cup of diameter d d d and height h h h , equating surface areas gives D b = d 2 + 4 d h D_b = \sqrt{d^2 + 4dh} D b ​ = d 2 + 4 d h ​

and with a corner radius r r r the expression is adjusted accordingly.

Anisotropy and earing

Rolled sheet has directional properties. The normal anisotropy ratio r ˉ \bar{r} r ˉ compares width strain to thickness strain; a high r ˉ \bar r r ˉ means the sheet resists thinning and draws well, so it raises the limiting drawing ratio. Planar anisotropy causes earing — wavy peaks and troughs around the rim of the drawn cup — which must be trimmed off as scrap. Steel developed specifically for drawing, such as interstitial-free grades, is processed to maximise r ˉ \bar r r ˉ and minimise planar variation.

Defects Summary

  • Defect Cause Remedy
  • Wrinkling in flange Circumferential compression unrestrained Increase blank holder force

Tearing at punch radius Excessive drawing force Reduce blank holder force; increase punch radius; better lubrication

  • Earing Planar anisotropy of the sheet Trim; select sheet with lower planar anisotropy
  • Surface scratching Poor lubrication or rough tooling Improve lubricant and tool finish
  • Excessive burr in shearing Worn tooling or wrong clearance Regrind punch; correct clearance
  • Orange peel Coarse grain size Use finer-grained material
  • Presses and Tooling
  • Press type Application
  • Mechanical (crank, eccentric) High speed, fixed stroke; blanking and piercing
  • Hydraulic Full force through the whole stroke; deep drawing
  • Knuckle joint Very high force near bottom dead centre; coining
  • Press brake Long bends in sheet

Mechanical presses deliver their rated force only near the bottom of the stroke, which suits shearing where the work is done in a short distance. Deep drawing needs force throughout a long stroke, which is why hydraulic presses dominate that application.