Study guide
14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming
Coal India Management Trainee CIL MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape
1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations
2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs
2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography
3 Chapter 3: Paper-I Reasoning & Logical Ability
3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning
4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude
4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude
5 Chapter 5: Paper-I General English & Verbal Ability
5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement
6 Chapter 6: Paper-II Engineering Mathematics
6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers
7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics
7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics
8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity
8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact
9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations
9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects
10 Chapter 10: Paper-II Machine Design & Failure Theories
10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat
11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery
11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy
12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery
12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams
13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning
13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics
14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology
14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation
15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree
14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming
Key Takeaways Explain This Topic AI
Plastic deformation and yield criteria, and load estimation for bulk forming, are named explicitly in the Casting, Forming and Joining bullet of the CIL Mechanical Paper-II syllabus.
The Tresca criterion predicts yielding when the maximum shear stress reaches half the uniaxial yield stress, while the von Mises criterion uses distortion energy and is generally more accurate for ductile metals.
In pure shear, Tresca gives the shear yield strength as half the tensile yield strength whereas von Mises gives it as the tensile yield divided by root three, so von Mises is the less conservative of the two.
Hot working above the recrystallisation temperature needs far lower forces and produces no strain hardening, while cold working strengthens the metal but requires much higher loads.
Last updated: August 2026
Plastic Deformation
Metal forming works because metals deform plastically without fracture. The mechanism is slip — the movement of dislocations along close-packed planes in close-packed directions. Face-centred cubic metals such as aluminium and copper have many available slip systems and are highly formable; hexagonal close-packed metals such as magnesium and zinc have few and are difficult to form cold.
A critical property of plastic deformation is that it occurs at constant volume . Since the volume is unchanged, ϵ 1 + ϵ 2 + ϵ 3 = 0 \epsilon_1 + \epsilon_2 + \epsilon_3 = 0 ϵ 1 + ϵ 2 + ϵ 3 = 0
in terms of true strains. This is why the Poisson's ratio of a metal in the fully plastic region is effectively 0.5 , against about 0.3 in the elastic region.
True strain is the appropriate measure for large deformation: ϵ = ln L L 0 = ln A 0 A \epsilon = \ln\frac{L}{L_0} = \ln\frac{A_0}{A} ϵ = ln L 0 L = ln A A 0
and unlike engineering strain, true strains are additive across successive passes.
Strain hardening is described by the power law σ = K ϵ n \sigma = K\epsilon^{n} σ = K ϵ n
where K K K is the strength coefficient and n n n the strain hardening exponent . A high n n n distributes deformation uniformly and delays necking; indeed, in a tensile test, necking begins when ϵ = n \epsilon = n ϵ = n .
Yield Criteria
A uniaxial tensile test gives one number, the yield stress σ y \sigma_y σ y . Forming processes impose complex three-dimensional stress states, so a criterion is needed to predict when yielding begins.
Tresca (maximum shear stress) criterion
Yielding occurs when the maximum shear stress reaches the value it has at yield in simple tension: σ 1 − σ 3 = σ y or τ max = σ y 2 \sigma_1 - \sigma_3 = \sigma_y \quad\text{or}\quad \tau_{\max} = \frac{\sigma_y}{2} σ 1 − σ 3 = σ y or τ m a x = 2 σ y
where σ 1 \sigma_1 σ 1 and σ 3 \sigma_3 σ 3 are the largest and smallest principal stresses. The intermediate principal stress plays no part, which is both the criterion's simplicity and its limitation.
Von Mises (distortion energy) criterion
Yielding occurs when the distortion energy per unit volume reaches its value at uniaxial yield: ( σ 1 − σ 2 ) 2 + ( σ 2 − σ 3 ) 2 + ( σ 3 − σ 1 ) 2 = 2 σ y 2 \left(\sigma_1-\sigma_2\right)^2 + \left(\sigma_2-\sigma_3\right)^2 + \left(\sigma_3-\sigma_1\right)^2 = 2\sigma_y^2 ( σ 1 − σ 2 ) 2 + ( σ 2 − σ 3 ) 2 + ( σ 3 − σ 1 ) 2 = 2 σ y 2
All three principal stresses participate. The criterion recognises that hydrostatic stress does not cause yielding — pure pressure changes volume, not shape — which is physically correct and confirmed experimentally: metals do not yield under uniform hydrostatic pressure however large.
Comparison
- Criterion Shear yield strength Relative prediction
- Tresca k = 0.5 σ y k = 0.5\,\sigma_y k = 0.5 σ y More conservative (predicts yield sooner)
Von Mises k = σ y 3 = 0.577 σ y k = \dfrac{\sigma_y}{\sqrt3} = 0.577\,\sigma_y k = 3 σ y = 0.577 σ y More accurate for ductile metals
The two criteria coincide in uniaxial tension and in balanced biaxial tension, and diverge most in pure shear , where they differ by about 15%. Plotted in principal stress space, the Tresca hexagon is inscribed within the von Mises ellipse.
For forming calculations the plane strain condition is common, and there the constrained yield stress rises: σ y ′ = 2 3 σ y = 1.155 σ y \sigma_y' = \frac{2}{\sqrt3}\sigma_y = 1.155\,\sigma_y σ y ′ = 3 2 σ y = 1.155 σ y
This factor of 1.155 appears throughout rolling and forging load calculations.
Hot Working Versus Cold Working
The dividing line is the recrystallisation temperature , roughly 0.4 T m 0.4\,T_m 0.4 T m on the absolute scale.
- Feature Hot working (above T r T_r T r ) Cold working (below T r T_r T r )
- Force required Low High
- Strain hardening None; recrystallisation removes it continuously Significant; metal strengthens as it deforms
- Achievable deformation Very large Limited before annealing needed
- Surface finish Poor; oxide scale forms Good
- Dimensional accuracy Poor Good
- Grain structure Refined, equiaxed Elongated, directional
- Residual stress Negligible Significant
Typical processes Rolling of slabs, forging of billets, extrusion of steel Cold rolling of sheet, wire drawing, coining
Note that hot working is defined relative to the recrystallisation temperature, not in absolute terms . Lead recrystallises below room temperature, so working lead at 20 degrees Celsius is hot working; tungsten worked at 1000 degrees Celsius is still cold working. This is a classic objective item.
Load Estimation: Forging
For open-die upset forging of a cylindrical billet of diameter d d d and height h h h between flat dies, friction at the die faces produces the characteristic friction hill — pressure rises from the edge towards the centre. The average forging pressure is approximately p avg = σ y ( 1 + 2 μ d 3 h ) p_{\text{avg}} = \sigma_y\left(1 + \frac{2\mu d}{3h}\right) p avg = σ y ( 1 + 3 h 2 μ d )
and the forging load is F = p avg × π d 2 4 F = p_{\text{avg}}\times\dfrac{\pi d^2}{4} F = p avg × 4 π d 2 .
The implication is important: as the workpiece is flattened, d d d grows and h h h shrinks, so d / h d/h d / h rises sharply and the required load escalates rapidly in the final stages. This is why forging presses are rated by the final thin section, not the starting billet.
Barrelling — the outward bulging of the sides — is caused by this same die friction restraining the ends. Good lubrication reduces both barrelling and load.
Load Estimation: Rolling
In flat rolling, the strip is drawn between rolls by friction. The maximum draft achievable in one pass is limited by the bite condition: Δ h max = μ 2 R \Delta h_{\max} = \mu^2 R Δ h m a x = μ 2 R
where R R R is the roll radius. Two immediate consequences:
Larger rolls take a bigger bite , which is why roughing mills use large rolls.
Higher friction takes a bigger bite , which is why hot rolling is done dry or with minimal lubricant while cold rolling is heavily lubricated to reduce load, accepting smaller drafts.
The roll force is approximately F = σ ˉ w L p , L p = R Δ h F = \bar{\sigma}\,w\,L_p, \qquad L_p = \sqrt{R\,\Delta h} F = σ ˉ w L p , L p = R Δ h
where w w w is strip width, L p L_p L p the projected contact length and σ ˉ \bar\sigma σ ˉ the mean flow stress in plane strain. The torque per roll is roughly F L p / 2 F L_p/2 F L p /2 , and the power for two rolls is 2 π N F L p / 60 2\pi N F L_p/60 2 π NF L p /60 .
The neutral point is where roll and strip surfaces move at the same speed. Before it the strip moves slower than the roll surface; after it, faster. The exit strip speed therefore exceeds the roll surface speed, an effect called forward slip .
Load Estimation: Extrusion
The extrusion ratio is R e = A 0 / A f R_e = A_0/A_f R e = A 0 / A f , and the ideal work per unit volume for homogeneous deformation is σ ˉ ln R e \bar\sigma\ln R_e σ ˉ ln R e . Including friction and redundant work empirically, p = k σ ˉ ln R e p = k\,\bar{\sigma}\ln R_e p = k σ ˉ ln R e
with k k k typically 1.2 to 2.0.
Type Description
Direct (forward) Ram and product move in the same direction; billet slides along the container, so friction is high and force falls as the billet shortens
Indirect (backward) Die moves into a stationary billet; no relative sliding along the container, so force is lower and nearly constant
- Hydrostatic Billet surrounded by pressurised fluid; almost no container friction
- Impact High-speed cold extrusion of soft metals such as toothpaste tubes
- Load Estimation: Wire Drawing
Unlike extrusion, drawing pulls the material through the die, so the drawing stress cannot exceed the yield strength of the emerging wire, or it will simply stretch and break. This sets a hard limit: σ d = σ ˉ ln A 0 A f < σ y \sigma_d = \bar\sigma\ln\frac{A_0}{A_f} \;<\; \sigma_y σ d = σ ˉ ln A f A 0 < σ y
For ideal frictionless drawing this gives ln ( A 0 / A f ) < 1 \ln(A_0/A_f) < 1 ln ( A 0 / A f ) < 1 , so the maximum reduction in one pass is 1 − 1 / e = 63 % 1 - 1/e = 63\% 1 − 1/ e = 63% in theory. With friction and redundant work included, practical single-pass reductions are 20 to 30%, which is why wire is drawn through a series of progressively smaller dies with intermediate annealing.
That theoretical 63% limit is one of the most-asked single numbers in bulk forming.