Study guide

8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

Key Takeaways Explain This Topic AI

Testing of materials with a universal testing machine and testing of hardness and impact strength are named explicitly in the CIL Mechanical Paper-II syllabus.

Brinell hardness uses a ball indenter and reports load divided by the curved surface area of the indentation, while Vickers and Rockwell use diamond indenters with different measurement bases.

Vickers hardness uses a 136 degree square-based diamond pyramid and gives a single continuous scale valid across soft and hard materials alike.

The Charpy test uses a horizontal simply supported specimen struck behind a notch, while the Izod test uses a vertical cantilever specimen struck above the notch on the notch side.

Last updated: August 2026

The Universal Testing Machine

A universal testing machine applies a controlled axial load and records the resulting deformation. The adjective universal reflects its ability to run tension, compression, bending and shear tests by changing fixtures.

  • Element Function
  • Load frame Two or four columns and a moving crosshead
  • Actuator Hydraulic or electromechanical (screw-driven)
  • Load cell Measures force, usually via a strain-gauged full bridge
  • Extensometer Measures gauge-length extension accurately
  • Grips and fixtures Wedge grips for tension, platens for compression, rollers for bending

Crosshead movement includes machine compliance and grip slip, so strain must be taken from the extensometer , not from crosshead travel, if the elastic modulus is to be measured correctly. This is a standard examination point and a real source of laboratory error.

Standard tensile specimens have a gauge length related to the cross-section so that results are comparable. For a round bar, the common proportional relation is L 0 = 5.65 A 0 L_0 = 5.65\sqrt{A_0} L 0 ​ = 5.65 A 0 ​ ​

Properties Read from a Tensile Test

  • Property How obtained
  • Young's modulus E E E Slope of the initial straight portion
  • Proportional limit Where the curve first departs from linearity
  • Yield strength Upper and lower yield points for mild steel; otherwise 0.2% offset proof stress
  • Ultimate tensile strength Maximum load divided by original area
  • Breaking strength Load at fracture divided by original area
  • Percentage elongation L f − L 0 L 0 × 100 \dfrac{L_f - L_0}{L_0}\times100 L 0 ​ L f ​ − L 0 ​ ​ × 100
  • Percentage reduction in area A 0 − A f A 0 × 100 \dfrac{A_0 - A_f}{A_0}\times100 A 0 ​ A 0 ​ − A f ​ ​ × 100
  • Toughness Total area under the stress-strain curve
  • Resilience Area up to the elastic limit; modulus of resilience is σ y 2 / 2 E \sigma_y^2/2E σ y 2 ​ /2 E

Ductile materials such as mild steel show necking and a cup-and-cone fracture; brittle materials such as grey cast iron fracture with little elongation on a plane roughly perpendicular to the load. Percentage elongation and reduction in area are the two standard ductility measures, and a material is conventionally regarded as ductile above about 5% elongation.

Hardness Testing

Hardness is resistance to localised plastic deformation. It is quick, effectively non-destructive, and correlates usefully with tensile strength — for steels, roughly UTS (MPa) ≈ 3.5 × BHN \text{UTS (MPa)} \approx 3.5 \times \text{BHN} UTS (MPa) ≈ 3.5 × BHN .

Brinell

A hardened steel or tungsten carbide ball of diameter D D D is pressed with load P P P for a set dwell time, and the indentation diameter d d d is measured optically. BHN = 2 P π D ( D − D 2 − d 2 ) \text{BHN} = \frac{2P}{\pi D\left(D - \sqrt{D^2 - d^2}\right)} BHN = π D ( D − D 2 − d 2 ​ ) 2 P ​

The denominator is the curved surface area of the impression, not its projected area. Brinell suits coarse-grained and heterogeneous materials such as castings because the large impression averages over the microstructure. It is unsuitable for very hard materials, where the ball itself deforms, and for thin sections.

Vickers

A square-based diamond pyramid with a face angle of 136 degrees is used, and the mean diagonal d d d of the impression is measured. VHN = 1.854 P d 2 \text{VHN} = \frac{1.854\,P}{d^2} VHN = d 2 1.854 P ​

Because the indenter is geometrically similar at all loads, the Vickers number is independent of load and gives one continuous scale from soft metals to hardened tool steel. This makes it the most versatile method, at the cost of requiring a well-polished surface and optical measurement.

Rockwell

Rockwell measures the depth of penetration under a major load beyond that under a preliminary minor load, and displays the result directly on a dial with no optical measurement.

  • Scale Indenter Major load Typical use
  • B 1/16 inch steel ball 100 kgf Soft steels, brass, aluminium
  • C Diamond cone (brale), 120 degrees 150 kgf Hardened steels
  • A Diamond cone 60 kgf Thin hard sheet, cemented carbides

The minor load of 10 kgf seats the indenter and eliminates surface irregularities from the reading. Rockwell is the fastest method and dominates production inspection; its disadvantage is that the scales are not directly comparable with one another.

Comparison

  • Test Indenter Measured Best for
  • Brinell Ball Impression diameter Castings, forgings, coarse structures
  • Vickers 136-degree diamond pyramid Impression diagonal All materials; one scale
  • Rockwell Ball or diamond cone Depth Fast production testing
  • Knoop Elongated diamond pyramid Long diagonal Microhardness, brittle materials, coatings
  • Shore scleroscope Rebound of a diamond-tipped hammer Rebound height Large parts, in situ

Impact Testing

A tensile test loads slowly; many service failures happen fast. Impact testing measures the energy absorbed in fracturing a notched specimen under a sudden blow, and is the standard route to assessing notch toughness .

Both standard tests use a swinging pendulum. The energy absorbed is the difference between the initial and final potential energy of the hammer: U = W l ( cos ⁡ β − cos ⁡ α ) U = W\,l\left(\cos\beta - \cos\alpha\right) U = W l ( cos β − cos α )

where α \alpha α is the release angle and β \beta β the swing-through angle.

Charpy versus Izod

This comparison is examined more often than anything else in the topic.

  • Feature Charpy Izod
  • Specimen orientation Horizontal Vertical
  • Support condition Simply supported at both ends Cantilever , clamped at the lower end
  • Notch faces Away from the hammer Towards the hammer
  • Struck Behind the notch, at mid-span Above the notch, on the notch side
  • Standard notch V-notch or keyhole, 2 mm deep V-notch, 2 mm deep
  • Common specimen 10 x 10 x 55 mm 10 x 10 x 75 mm
  • Prevalence International standard; used for low-temperature testing More common in some polymer standards

The memory hook: Charpy is a simply supported beam struck opposite the notch; Izod is a cantilever struck on the notch side.

The ductile-brittle transition

Body-centred cubic metals — notably plain carbon and low-alloy structural steels — show a sharp drop in absorbed energy as temperature falls, through a ductile-brittle transition temperature . Above it, fracture surfaces are fibrous and dull with large energy absorption; below it, they are bright and crystalline with very little.

Face-centred cubic metals such as austenitic stainless steel, aluminium and copper show no such transition and remain tough at low temperature. This is why austenitic stainless steel is specified for cryogenic vessels.

The engineering significance is severe and historical: brittle fracture of ship hulls and pressure vessels in cold service traces directly to operating below the transition temperature. For mining equipment in northern Indian winters, or for imported plant designed for warmer service, the transition temperature is a genuine specification issue rather than an academic one.

Factors that raise the transition temperature, and therefore make brittle failure more likely, are increased carbon content, coarse grain size, higher strain rate, sharper notches and greater section thickness. Grain refinement and nickel additions lower it.

Notch sensitivity

The notch is not incidental. It creates a triaxial stress state that suppresses plastic flow, so the notched specimen may fail brittly under conditions where an unnotched one would not. Impact energy figures are therefore always quoted with the notch geometry, and results from V-notch and keyhole specimens are not interchangeable.

Other Tests in Brief

  • Test Measures
  • Fatigue (rotating beam) Endurance limit and the S-N curve
  • Creep Time-dependent strain under constant load at elevated temperature
  • Compression Behaviour of brittle materials such as concrete and cast iron
  • Torsion Shear modulus and shear strength
  • Fracture toughness Critical stress intensity factor for a cracked body

Together with the tensile, hardness and impact tests above, these form the acceptance-testing framework referred to throughout the machine design and materials chapters of Paper-II.