Study guide

8.8 Strain Gauges, Rosettes & Experimental Stress Analysis

Coal India Management Trainee CIL MT

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape

1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations

2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs

2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography

3 Chapter 3: Paper-I Reasoning & Logical Ability

3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning

4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude

4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude

5 Chapter 5: Paper-I General English & Verbal Ability

5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement

6 Chapter 6: Paper-II Engineering Mathematics

6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers

7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics

7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics

8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity

8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact

9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations

9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects

10 Chapter 10: Paper-II Machine Design & Failure Theories

10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat

11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery

11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy

12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery

12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams

13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning

13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics

14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology

14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation

15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR

15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree

8.8 Strain Gauges, Rosettes & Experimental Stress Analysis

Key Takeaways Explain This Topic AI

Strain gauges and rosettes are named explicitly in the Mechanics of Materials bullet of the CIL Mechanical Paper-II syllabus.

A bonded electrical resistance strain gauge works because its resistance changes in proportion to strain, quantified by the gauge factor.

The gauge factor of a common metallic foil gauge is about 2, whereas semiconductor gauges reach 100 or more at the cost of poorer temperature stability.

A rosette of three gauges is required to determine a general plane strain state, because three independent quantities must be found and one gauge measures only one direction.

Last updated: August 2026

Why Measure Strain Rather Than Stress

Stress cannot be measured directly. What an instrument can detect is deformation , and stress is then inferred through the constitutive law. Every experimental stress analysis technique therefore measures strain and computes stress from it.

This matters practically in a coal operation: dragline booms, shovel dipper handles, conveyor gantries and haul-truck chassis are all validated by strain gauging under service load, because their real loading is far more complex than any design idealisation.

The Electrical Resistance Strain Gauge

A thin metal foil grid is bonded to the surface so that it deforms with it. Stretching the foil makes it longer and thinner, both of which raise its electrical resistance. For a conductor of resistivity ρ \rho ρ , length L L L and area A A A : R = ρ L A R = \frac{\rho L}{A} R = A ρ L ​

Differentiating and collecting terms gives Δ R R = ( 1 + 2 μ ) ϵ + Δ ρ ρ \frac{\Delta R}{R} = (1 + 2\mu)\epsilon + \frac{\Delta\rho}{\rho} R Δ R ​ = ( 1 + 2 μ ) ϵ + ρ Δ ρ ​

The bracketed term comes from the geometry change and the last from the piezoresistive effect. Collecting everything into a single constant defines the gauge factor : G f = Δ R / R ϵ \boxed{G_f = \frac{\Delta R/R}{\epsilon}} G f ​ = ϵ Δ R / R ​ ​

  • Gauge type Typical gauge factor Comment
  • Metallic foil (constantan) ~2.0 Standard; stable, linear, temperature-tolerant
  • Nichrome, Karma 2.0 - 2.2 Better fatigue and temperature performance
  • Platinum alloys 4 - 6 High temperature service
  • Semiconductor (silicon) 100 - 200 Very sensitive but non-linear and temperature-sensitive

The number to remember is that a common foil gauge has G f ≈ 2 G_f \approx 2 G f ​ ≈ 2 .

The magnitude problem

Typical elastic strains are of the order of 1000 μ ϵ 1000\,\mu\epsilon 1000 μ ϵ , that is 10 − 3 10^{-3} 1 0 − 3 . With G f = 2 G_f = 2 G f ​ = 2 , the fractional resistance change is only 2 × 10 − 3 2\times10^{-3} 2 × 1 0 − 3 — for a 120 ohm gauge, a change of 0.24 ohm. Detecting that reliably requires a bridge circuit, not a plain ohmmeter.

The Wheatstone Bridge

The gauge forms one arm of a Wheatstone bridge. At balance the output is zero; a small resistance change unbalances it and produces a measurable voltage.

  • Configuration Active gauges Benefit
  • Quarter bridge 1 Simplest; needs separate temperature compensation
  • Half bridge 2 Doubles output; provides temperature compensation automatically
  • Full bridge 4 Quadruples output; best compensation and linearity
  • Temperature compensation

Temperature affects a gauge in two ways: the foil's resistivity changes, and differential thermal expansion between gauge and specimen produces apparent strain. Both are indistinguishable from real strain in a single gauge.

The standard remedy is a dummy gauge : an identical gauge bonded to an unstressed piece of the same material, kept at the same temperature, and placed in the adjacent bridge arm. Both gauges see the same thermal effect, which therefore cancels in the bridge output, while only the active gauge sees mechanical strain.

In a bending application, mounting one gauge on the tension face and one on the compression face in adjacent arms doubles the output and compensates temperature simultaneously — the reason half-bridge arrangements are standard in load cells and torque transducers.

Strain Rosettes

A single gauge measures normal strain in one direction only . A general plane strain state has three independent components — ϵ x \epsilon_x ϵ x ​ , ϵ y \epsilon_y ϵ y ​ and γ x y \gamma_{xy} γ x y ​ — so three gauge readings at known angles are required. That cluster is a rosette .

The general transformation for a gauge at angle θ \theta θ from the reference axis is ϵ θ = ϵ x + ϵ y 2 + ϵ x − ϵ y 2 cos ⁡ 2 θ + γ x y 2 sin ⁡ 2 θ \epsilon_\theta = \frac{\epsilon_x + \epsilon_y}{2} + \frac{\epsilon_x - \epsilon_y}{2}\cos2\theta + \frac{\gamma_{xy}}{2}\sin2\theta ϵ θ ​ = 2 ϵ x ​ + ϵ y ​ ​ + 2 ϵ x ​ − ϵ y ​ ​ cos 2 θ + 2 γ x y ​ ​ sin 2 θ

which is the strain analogue of the stress transformation used in Mohr's circle.

Rectangular (45-degree) rosette

Gauges at 0, 45 and 90 degrees, giving readings ϵ a \epsilon_a ϵ a ​ , ϵ b \epsilon_b ϵ b ​ and ϵ c \epsilon_c ϵ c ​ : ϵ x = ϵ a , ϵ y = ϵ c , γ x y = 2 ϵ b − ( ϵ a + ϵ c ) \epsilon_x = \epsilon_a, \qquad \epsilon_y = \epsilon_c, \qquad \gamma_{xy} = 2\epsilon_b - (\epsilon_a + \epsilon_c) ϵ x ​ = ϵ a ​ , ϵ y ​ = ϵ c ​ , γ x y ​ = 2 ϵ b ​ − ( ϵ a ​ + ϵ c ​ )

The principal strains follow: ϵ 1 , 2 = ϵ a + ϵ c 2 ± 1 2 ( ϵ a − ϵ b ) 2 + ( ϵ b − ϵ c ) 2 \epsilon_{1,2} = \frac{\epsilon_a + \epsilon_c}{2} \pm \frac{1}{\sqrt2}\sqrt{(\epsilon_a - \epsilon_b)^2 + (\epsilon_b - \epsilon_c)^2} ϵ 1 , 2 ​ = 2 ϵ a ​ + ϵ c ​ ​ ± 2 ​ 1 ​ ( ϵ a ​ − ϵ b ​ ) 2 + ( ϵ b ​ − ϵ c ​ ) 2 ​

and the principal direction from tan ⁡ 2 θ p = 2 ϵ b − ϵ a − ϵ c ϵ a − ϵ c \tan2\theta_p = \frac{2\epsilon_b - \epsilon_a - \epsilon_c}{\epsilon_a - \epsilon_c} tan 2 θ p ​ = ϵ a ​ − ϵ c ​ 2 ϵ b ​ − ϵ a ​ − ϵ c ​ ​

Delta (60-degree) rosette

Gauges at 0, 60 and 120 degrees: ϵ 1 , 2 = ϵ a + ϵ b + ϵ c 3 ± 2 3 ( ϵ a − ϵ b ) 2 + ( ϵ b − ϵ c ) 2 + ( ϵ c − ϵ a ) 2 \epsilon_{1,2} = \frac{\epsilon_a+\epsilon_b+\epsilon_c}{3} \pm \frac{\sqrt2}{3}\sqrt{(\epsilon_a-\epsilon_b)^2 + (\epsilon_b-\epsilon_c)^2 + (\epsilon_c-\epsilon_a)^2} ϵ 1 , 2 ​ = 3 ϵ a ​ + ϵ b ​ + ϵ c ​ ​ ± 3 2 ​ ​ ( ϵ a ​ − ϵ b ​ ) 2 + ( ϵ b ​ − ϵ c ​ ) 2 + ( ϵ c ​ − ϵ a ​ ) 2 ​

The delta rosette distributes the gauges more evenly and is slightly less sensitive to any single reading error, but the rectangular rosette is easier to align and far more common.

From strain to stress

Once principal strains are known, principal stresses follow from the two-dimensional Hooke's law: σ 1 = E 1 − μ 2 ( ϵ 1 + μ ϵ 2 ) , σ 2 = E 1 − μ 2 ( ϵ 2 + μ ϵ 1 ) \sigma_1 = \frac{E}{1-\mu^2}\left(\epsilon_1 + \mu\epsilon_2\right), \qquad \sigma_2 = \frac{E}{1-\mu^2}\left(\epsilon_2 + \mu\epsilon_1\right) σ 1 ​ = 1 − μ 2 E ​ ( ϵ 1 ​ + μ ϵ 2 ​ ) , σ 2 ​ = 1 − μ 2 E ​ ( ϵ 2 ​ + μ ϵ 1 ​ )

The factor 1 / ( 1 − μ 2 ) 1/(1-\mu^2) 1/ ( 1 − μ 2 ) is essential. Computing σ = E ϵ \sigma = E\epsilon σ = E ϵ from a rosette reading is a frequent and serious error, because it ignores the transverse stress entirely.

Worked example

A rectangular rosette on a dragline boom reads ϵ a = 600 μ ϵ \epsilon_a = 600\,\mu\epsilon ϵ a ​ = 600 μ ϵ , ϵ b = 200 μ ϵ \epsilon_b = 200\,\mu\epsilon ϵ b ​ = 200 μ ϵ , ϵ c = − 200 μ ϵ \epsilon_c = -200\,\mu\epsilon ϵ c ​ = − 200 μ ϵ . Find the principal strains. ϵ 1 , 2 = 600 − 200 2 ± 1 2 ( 600 − 200 ) 2 + ( 200 + 200 ) 2 \epsilon_{1,2} = \frac{600 - 200}{2} \pm \frac{1}{\sqrt2}\sqrt{(600-200)^2 + (200+200)^2} ϵ 1 , 2 ​ = 2 600 − 200 ​ ± 2 ​ 1 ​ ( 600 − 200 ) 2 + ( 200 + 200 ) 2 ​ = 200 ± 1 2 160000 + 160000 = 200 ± 565.7 1.414 = 200 ± 400 = 200 \pm \frac{1}{\sqrt2}\sqrt{160000 + 160000} = 200 \pm \frac{565.7}{1.414} = 200 \pm 400 = 200 ± 2 ​ 1 ​ 160000 + 160000 ​ = 200 ± 1.414 565.7 ​ = 200 ± 400

So ϵ 1 = 600 μ ϵ \epsilon_1 = 600\,\mu\epsilon ϵ 1 ​ = 600 μ ϵ and ϵ 2 = − 200 μ ϵ \epsilon_2 = -200\,\mu\epsilon ϵ 2 ​ = − 200 μ ϵ . With E = 200 E = 200 E = 200 GPa and μ = 0.3 \mu = 0.3 μ = 0.3 : σ 1 = 200000 1 − 0.09 ( 600 + 0.3 ( − 200 ) ) × 10 − 6 = 200000 0.91 × 540 × 10 − 6 = 118.7 MPa \sigma_1 = \frac{200000}{1-0.09}\left(600 + 0.3(-200)\right)\times10^{-6} = \frac{200000}{0.91}\times540\times10^{-6} = 118.7 \text{ MPa} σ 1 ​ = 1 − 0.09 200000 ​ ( 600 + 0.3 ( − 200 ) ) × 1 0 − 6 = 0.91 200000 ​ × 540 × 1 0 − 6 = 118.7 MPa

Other Experimental Methods

Method Principle Best for

Photoelasticity Transparent model under load becomes birefringent; fringe order gives the difference of principal stresses Whole-field visualisation; stress concentration at fillets and holes

Brittle coating A lacquer cracks perpendicular to maximum principal tensile strain Quick location of highly stressed zones and their directions before gauging

Moire fringe Interference between reference and deformed gratings Whole-field displacement

Digital image correlation Tracking a speckle pattern between images Full-field strain without surface preparation for gauges

The practical workflow in industry combines them: a brittle coating or photoelastic model first identifies where the peak stress is and in what direction , and strain gauges or rosettes are then bonded there to measure it accurately.