Study guide
15.5 Comparators & Interferometry
Coal India Management Trainee CIL MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape
1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations
2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs
2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography
3 Chapter 3: Paper-I Reasoning & Logical Ability
3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning
4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude
4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude
5 Chapter 5: Paper-I General English & Verbal Ability
5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement
6 Chapter 6: Paper-II Engineering Mathematics
6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers
7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics
7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics
8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity
8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact
9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations
9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects
10 Chapter 10: Paper-II Machine Design & Failure Theories
10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat
11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery
11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy
12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery
12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams
13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning
13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics
14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology
14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation
15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree
15.5 Comparators & Interferometry
Key Takeaways Explain This Topic AI
Comparators and interferometry are named explicitly in the Metrology and Inspection bullet of the CIL Mechanical Paper-II syllabus.
A comparator does not measure absolute size; it measures the deviation of a workpiece from a known standard to which it has first been set.
Mechanical comparators use lever and gear magnification, optical comparators use light beams as weightless levers, and pneumatic comparators infer size from air flow or back pressure.
Interferometry measures length in terms of the wavelength of light, giving the highest accuracy of any dimensional method and forming the basis of the definition of the metre.
Last updated: August 2026
The Comparison Principle
A comparator does not measure absolute dimension. It is first set to a known standard — usually a stack of slip gauges — and thereafter indicates only the deviation of each workpiece from that standard. This distinction is fundamental and frequently examined.
The advantage is decisive in production inspection. Measuring a 50.00 mm shaft to one micrometre absolutely requires an instrument accurate over its whole 50 mm range. Measuring the same shaft as plus 3 micrometres from a 50 mm standard requires accuracy only over a range of a few tens of micrometres, which is enormously easier and cheaper to achieve.
Characteristics of a good comparator
- Requirement Reason
- High magnification Small deviations must be visible
- Linear scale Reading must be proportional to displacement throughout
- Freedom from backlash and friction Repeatability
- Low inertia of moving parts Rapid, undamped response
- Minimal temperature sensitivity Metrology rooms are held at 20 degrees Celsius
- Adequate measuring range around the set point Usable without constant resetting
- Robust and easy to use Production floor environment
Note the inherent trade-off: magnification and range are opposed . A comparator with 10,000 times magnification has a very small usable range, which is why several types exist for different duties.
Mechanical Comparators
Magnification is obtained by levers, gear trains, or a combination.
Dial indicator
The plunger carries a rack that drives a pinion, and a gear train amplifies the rotation to a pointer. Magnification is typically 100 to 1000 times, with readings to 0.01 mm or 0.002 mm. It is the most common shop-floor comparator, used with a stand for bench work and mounted on machines for run-out checking.
Sigma comparator
Uses a knife-edge and a cross-strip hinge in place of a pivot, eliminating friction and backlash. A forked arm and a thin metal band wrapped around a drum give the second stage of magnification. Magnification reaches around 5,000, with readings to 0.0002 mm.
Johansson Mikrokator
A thin twisted metal strip carries a very light glass pointer at its centre. Axial tension applied by the plunger causes the strip to untwist , rotating the pointer. Because the mechanism has almost no mass and no rubbing contact, response is fast and hysteresis is negligible. Magnification reaches about 5,000.
Optical Comparators
Optical systems use a light beam as a weightless lever , which has three advantages: no mass, no friction, and no wear. A small tilt of a mirror produces a large movement of the reflected spot on a distant scale.
A critical geometric fact: rotating a mirror through angle θ \theta θ deviates the reflected ray through 2 θ 2\theta 2 θ , so the optical system contributes a factor of two before any lever ratio is considered.
Zeiss Ultra-optimeter
A plunger tilts a mirror, and the reflected beam is projected onto a graduated screen after multiple reflections. Magnification reaches 10,000 to 15,000 times , among the highest of any comparator.
Optical projector (profile projector)
Rather than magnifying a displacement, this magnifies the whole profile of a small component, projecting its silhouette at 10, 20, 50 or 100 times onto a screen where it is compared against a drawn chart. It is the standard method for inspecting screw thread forms, gear tooth profiles and small complex parts, since it checks form and dimension simultaneously.
Pneumatic Comparators
Air at controlled pressure escapes through the clearance between a gauging jet and the workpiece surface. The clearance controls the flow, and the flow or the resulting back pressure indicates the dimension.
- Type Principle
- Flow (Solex) type A float rises in a tapered glass tube according to the air flow rate
- Back pressure type Pressure between a control orifice and the measuring jet is read on a gauge
- Why pneumatic gauging matters in production
No physical contact , so soft, thin or highly finished surfaces are not marked.
Magnification of 1,000 to 30,000 times is readily achieved.
Bores are measured directly , including deep, blind and interrupted bores that a mechanical instrument cannot reach.
The gauging head is remote from the display, so measurement is possible in awkward positions and inside machines.
The air flow blows swarf and coolant away from the measuring zone, which is a genuine advantage on a production line.
Several jets can measure taper, ovality and bell-mouth in one operation.
The limitation is that the workpiece surface must be reasonably smooth, since roughness affects the escaping air flow, and each gauge is dedicated to one nominal size.
Electrical and Electronic Comparators
A displacement is converted into an electrical signal, most commonly by an LVDT — Linear Variable Differential Transformer — in which a moving ferrite core alters the coupling between a primary and two opposed secondary coils. The output is linear over the working range, frictionless, and has effectively infinite resolution.
Advantages that matter industrially: the signal can be amplified electronically to any magnification , recorded and logged automatically , used for statistical process control , and fed to automatic sorting or in-process gauging that stops a grinding machine at size. Multiple transducers can be combined arithmetically, so a single readout can display, for example, the difference between two measurements.
Comparator Comparison
- Type Typical magnification Contact Key advantage
- Dial indicator 100 - 1,000 Yes Cheap, robust, universal
- Sigma / Mikrokator up to 5,000 Yes Frictionless mechanism, high repeatability
- Optical (Zeiss) 10,000 - 15,000 Yes Very high magnification, no moving mass
- Pneumatic 1,000 - 30,000 No Bores, delicate surfaces, self-cleaning
- Electrical (LVDT) Electronically variable Yes Recording, automation, in-process gauging
- Interferometry
Interferometry measures length in terms of the wavelength of light , which is why it sits at the apex of the accuracy hierarchy. Since 1983 the metre has been defined in terms of the speed of light, and practical realisation of that definition is by interferometry using stabilised lasers.
The optical flat
An optical flat is a disc of glass or fused quartz with faces flat to a fraction of a wavelength. Placed on a workpiece surface, it forms a thin wedge of air. Light reflected from the underside of the flat interferes with light reflected from the workpiece, producing alternating dark and light bands called interference fringes.
The governing relation is that consecutive dark fringes correspond to an air gap change of half a wavelength : Δ h = λ 2 \Delta h = \frac{\lambda}{2} Δ h = 2 λ
For the helium 587.6 nm line commonly used, each fringe represents about 0.294 micrometres . Height difference over a surface is therefore h = n λ 2 h = n\,\frac{\lambda}{2} h = n 2 λ
where n n n is the number of fringes counted.
Reading fringe patterns
The pattern is a contour map of the surface:
- Fringe appearance Surface condition
- Straight, parallel, evenly spaced Flat
- Curved Convex or concave
- Closely spaced Steep wedge or large error
- Widely spaced Nearly parallel surfaces
- Irregular, broken Local high or low spots
Distinguishing convex from concave requires pressing lightly at one edge of the flat and observing which way the fringes move — a practical technique rather than a purely optical deduction.
Worked example
An optical flat placed on a gauge block face shows 8 fringes across a 20 mm length, using light of wavelength 0.5 micrometres. The height variation is h = 8 × 0.5 2 = 2 micrometres h = 8\times\frac{0.5}{2} = 2 \text{ micrometres} h = 8 × 2 0.5 = 2 micrometres
Slip gauge interferometers
The NPL flatness interferometer and the Pitter-NPL gauge interferometer are used to calibrate slip gauges against the wavelength of light. The gauge is wrung to a base plate, illuminated with monochromatic light, and the fractional fringe displacement between gauge face and base plate gives the deviation from nominal length. Using several wavelengths together resolves the ambiguity of whole fringe counts — the method of exact fractions.
Laser interferometry
A stabilised helium-neon laser at 632.8 nm, with a beam splitter and retroreflectors, measures displacement to a resolution of nanometres over distances of tens of metres. It is the standard method for calibrating machine tool axes and coordinate measuring machines , and for checking positional accuracy, repeatability and backlash of CNC slides. Environmental compensation for air temperature, pressure and humidity is essential, because these alter the refractive index of air and hence the effective wavelength.