Study guide
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology
Coal India Management Trainee CIL MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape
1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations
2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs
2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography
3 Chapter 3: Paper-I Reasoning & Logical Ability
3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning
4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude
4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude
5 Chapter 5: Paper-I General English & Verbal Ability
5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement
6 Chapter 6: Paper-II Engineering Mathematics
6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers
7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics
7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics
8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity
8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact
9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations
9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects
10 Chapter 10: Paper-II Machine Design & Failure Theories
10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat
11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery
11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy
12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery
12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams
13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning
13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics
14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology
14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation
15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology
Key Takeaways Explain This Topic AI
Fundamental tolerance unit formula is i = 0.45(D^(1/3)) + 0.001D in microns, where D is the geometric mean of diameter steps
The ISO/IS 919 standard specifies 18 tolerance grades (IT01 to IT16) and 25 fundamental deviation letter designations for holes and shafts
Taylor's Principle of Gauge Design mandates that GO gauges inspect Maximum Material Condition (MMC) and full form, whereas NO-GO gauges inspect Least Material Condition (LMC) at a single dimension
Sine bar setup obeys sin(theta) = h/L and is practically restricted to angles below 45 degrees to avoid extreme angular error sensitivity
Theoretical peak-to-valley surface roughness in single-point turning is Rt = f^2 / (8 * R_nose), yielding an arithmetic average Ra = f^2 / (32 * R_nose)
Last updated: August 2026
Limits, Fits, Tolerances, Gauges & Surface Metrology
In heavy engineering and mining machinery manufacturing—such as the massive draglines, continuous miners, and longwall shearers deployed by Coal India Limited—interchangeability of mating components is paramount. Interchangeability ensures that any one component selected at random from a batch will assemble and function correctly with a mating component without custom fitting or secondary machining.
1. Terminology of Limits and Fits (IS 919 / ISO System)
The Indian Standard IS 919 (aligned with ISO 286) establishes a standardized framework for defining linear dimensional limits, tolerances, and mating relationships between cylindrical features (holes and shafts). +-------------------------------------------+ <-- Upper Limit of Hole (ES)
- | |
- | HOLE TOLERANCE (Th) |
- Hole Size | | <-- Lower Limit of Hole (EI)
- +-------------------------------------------+
- ============================================================= <-- ZERO LINE (Basic Size)
- +-------------------------------------------+ <-- Upper Limit of Shaft (es)
- | |
- Shaft Size | SHAFT TOLERANCE (Ts) |
- | | <-- Lower Limit of Shaft (ei)
- +-------------------------------------------+
- Core Definitions
Basic Size ( D D D ): The exact theoretical size from which limits of size are derived by the application of deviations.
Actual Size: The size of a manufactured component obtained by direct measurement.
Limits of Size: The two extreme permissible dimensions between which the actual size must lie:
Upper Limit ( U L UL UL ): Maximum permissible dimension.
Lower Limit ( L L LL LL ): Minimum permissible dimension.
Tolerance ( T T T ): The total permissible variation in a dimension: Tolerance = U L − L L = Upper Deviation − Lower Deviation \text{Tolerance} = UL - LL = \text{Upper Deviation} - \text{Lower Deviation} Tolerance = UL − LL = Upper Deviation − Lower Deviation
Zero Line: A graphical reference line representing the basic size. Positive deviations lie above the zero line; negative deviations lie below it.
Deviations:
Upper Deviation ( E S ES ES for Hole, e s es es for Shaft): Algebraic difference between upper limit and basic size: E S = U L hole − D basic , e s = U L shaft − D basic ES = UL_{\text{hole}} - D_{\text{basic}}, \quad es = UL_{\text{shaft}} - D_{\text{basic}} ES = U L hole − D basic , es = U L shaft − D basic
Lower Deviation ( E I EI E I for Hole, e i ei e i for Shaft): Algebraic difference between lower limit and basic size: E I = L L hole − D basic , e i = L L shaft − D basic EI = LL_{\text{hole}} - D_{\text{basic}}, \quad ei = LL_{\text{shaft}} - D_{\text{basic}} E I = L L hole − D basic , e i = L L shaft − D basic
Fundamental Deviation: The deviation closest to the zero line that defines the position of the tolerance zone relative to the basic size.
2. Standard Tolerance Grades and Fundamental Tolerance Unit ( i i i )
The ISO/IS system specifies 18 standard tolerance grades : IT01 , IT0 , IT1 , IT2 , … , IT16 \text{IT01}, \text{IT0}, \text{IT1}, \text{IT2}, \dots, \text{IT16} IT01 , IT0 , IT1 , IT2 , … , IT16 .
Grades IT01 \text{IT01} IT01 to IT4 \text{IT4} IT4 are for high-precision master gauges.
Grades IT5 \text{IT5} IT5 to IT7 \text{IT7} IT7 are for precision fits and fine manufacturing (grinding, broaching, reaming).
Grades IT8 \text{IT8} IT8 to IT11 \text{IT11} IT11 are for general engineering production (turning, milling, drilling).
Grades IT12 \text{IT12} IT12 to IT16 \text{IT16} IT16 are for coarse processes (casting, forging, stamping).
Mathematical Formulation of Tolerance Unit ( i i i )
For basic sizes up to 500 mm 500\text{ mm} 500 mm , the standard tolerance unit i i i (in micrometers, μ m \mu\text{m} μ m ) is given by: ∋ = 0.45 D 3 + 0.001 D \ni = 0.45\sqrt[3]{D} + 0.001 D ∋= 0.45 3 D + 0.001 D
where:
D D D is the geometric mean diameter (in mm \text{mm} mm ) of the diameter step boundaries D 1 D_1 D 1 and D 2 D_2 D 2 : D = D 1 ⋅ D 2 D = \sqrt{D_1 \cdot D_2} D = D 1 ⋅ D 2
Note: The term 0.45 D 3 0.45\sqrt[3]{D} 0.45 3 D accounts for machining errors, while 0.001 D 0.001 D 0.001 D accounts for measuring and thermal errors.
Values of Standard Tolerance Grades
For basic tolerance grades IT5 \text{IT5} IT5 through IT16 \text{IT16} IT16 , the tolerance magnitude is a fixed multiple of i i i :
- Tolerance Grade Multiplier of i i i Numerical Value ( μ m \mu\text{m} μ m )
- IT5 \text{IT5} IT5 7 i 7i 7 i 7 i 7i 7 i
- IT6 \text{IT6} IT6 10 i 10i 10 i 10 i 10i 10 i
- IT7 \text{IT7} IT7 16 i 16i 16 i 16 i 16i 16 i
- IT8 \text{IT8} IT8 25 i 25i 25 i 25 i 25i 25 i
- IT9 \text{IT9} IT9 40 i 40i 40 i 40 i 40i 40 i
- IT10 \text{IT10} IT10 64 i 64i 64 i 64 i 64i 64 i
- IT11 \text{IT11} IT11 100 i 100i 100 i 100 i 100i 100 i
- IT12 \text{IT12} IT12 160 i 160i 160 i 160 i 160i 160 i
- IT13 \text{IT13} IT13 250 i 250i 250 i 250 i 250i 250 i
- IT14 \text{IT14} IT14 400 i 400i 400 i 400 i 400i 400 i
- IT15 \text{IT15} IT15 640 i 640i 640 i 640 i 640i 640 i
- IT16 \text{IT16} IT16 1000 i 1000i 1000 i 1000 i 1000i 1000 i
Notice that tolerance values increase in geometric progression with a common ratio r = 10 5 ≈ 1.585 r = \sqrt[5]{10} \approx 1.585 r = 5 10 ≈ 1.585 , meaning the tolerance increases by a factor of 10 every 5 grades (e.g., IT11 = 10 × IT6 \text{IT11} = 10 \times \text{IT6} IT11 = 10 × IT6 ). For sizes between 500 mm 500\text{ mm} 500 mm and 3150 mm 3150\text{ mm} 3150 mm , the measuring unit is I = 0.004 D + 2.1 I = 0.004 D + 2.1 I = 0.004 D + 2.1 .
3. Fundamental Deviations and Classification of Fits
There are 25 fundamental deviations represented by letters:
Capital letters ( A , B , C , C D , D , E , E F , F , F G , G , H , J , J S , K , M , N , P , R , S , T , U , V , X , Y , Z A, B, C, CD, D, E, EF, F, FG, G, H, J, JS, K, M, N, P, R, S, T, U, V, X, Y, Z A , B , C , C D , D , E , EF , F , FG , G , H , J , J S , K , M , N , P , R , S , T , U , V , X , Y , Z ) for holes .
Small letters ( a , b , c , c d , d , e , e f , f , f g , g , h , j , j s , k , m , n , p , r , s , t , u , v , x , y , z a, b, c, cd, d, e, ef, f, fg, g, h, j, js, k, m, n, p, r, s, t, u, v, x, y, z a , b , c , c d , d , e , e f , f , f g , g , h , j , j s , k , m , n , p , r , s , t , u , v , x , y , z ) for shafts .
Systems of Fits
Hole-Basis System ( H H H -hole): The basic size is the lower limit of the hole. Lower deviation E I = 0 EI = 0 E I = 0 . This is universally preferred in industrial practice because standardized fixed-size tools (drills, reamers, broaches) can be used to produce the hole, and shafts can be turned/ground to suit the desired fit.
Shaft-Basis System ( h h h -shaft): The basic size is the upper limit of the shaft. Upper deviation e s = 0 es = 0 es = 0 . Used where a single continuous shaft diameter accommodates multiple components requiring different fits. FIT CLASSIFICATION
- |
- +---------------------------------+---------------------------------+
- | | |
- CLEARANCE FIT TRANSITION FIT INTERFERENCE FIT
- Hole > Shaft Hole ~ Shaft Shaft > Hole
- (e.g., H7/g6, H7/f7) (e.g., H7/k6, H7/n6) (e.g., H7/p6, H7/u6)
- Quantitative Conditions for Fits
Clearance Fit: The tolerance zone of the hole is entirely above that of the shaft. Minimum Clearance = L L hole − U L shaft = E I − e s > 0 \text{Minimum Clearance} = LL_{\text{hole}} - UL_{\text{shaft}} = EI - es > 0 Minimum Clearance = L L hole − U L shaft = E I − es > 0 Maximum Clearance = U L hole − L L shaft = E S − e i \text{Maximum Clearance} = UL_{\text{hole}} - LL_{\text{shaft}} = ES - ei Maximum Clearance = U L hole − L L shaft = ES − e i
Interference Fit: The tolerance zone of the shaft is entirely above that of the hole. Minimum Interference = L L shaft − U L hole = e i − E S > 0 \text{Minimum Interference} = LL_{\text{shaft}} - UL_{\text{hole}} = ei - ES > 0 Minimum Interference = L L shaft − U L hole = e i − ES > 0 Maximum Interference = U L shaft − L L hole = e s − E I \text{Maximum Interference} = UL_{\text{shaft}} - LL_{\text{hole}} = es - EI Maximum Interference = U L shaft − L L hole = es − E I
Transition Fit: The tolerance zones of the hole and shaft overlap. Depending on actual assembly sizes, either clearance or interference may result. Maximum Clearance = U L hole − L L shaft = E S − e i > 0 \text{Maximum Clearance} = UL_{\text{hole}} - LL_{\text{shaft}} = ES - ei > 0 Maximum Clearance = U L hole − L L shaft = ES − e i > 0 Maximum Interference = U L shaft − L L hole = e s − E I > 0 \text{Maximum Interference} = UL_{\text{shaft}} - LL_{\text{hole}} = es - EI > 0 Maximum Interference = U L shaft − L L hole = es − E I > 0
4. Worked Calculation: Limits and Fits
Problem: A clearance fit is designated as 50 mm H 7 / g 6 50\text{ mm } H7/g6 50 mm H 7/ g 6 . The diameter step is 30 mm 30\text{ mm} 30 mm to 50 mm 50\text{ mm} 50 mm . The fundamental deviation for shaft g g g is − 2.5 D 0.34 μ m -2.5 D^{0.34}\;\mu\text{m} − 2.5 D 0.34 μ m . Calculate:
- Fundamental tolerance unit i i i
- Tolerances for hole and shaft
- Limits of hole and shaft
- Maximum and minimum clearances
Solution:
Mean diameter D D D : D = 30 × 50 = 1500 ≈ 38.7298 mm D = \sqrt{30 \times 50} = \sqrt{1500} \approx 38.7298\text{ mm} D = 30 × 50 = 1500 ≈ 38.7298 mm
Fundamental tolerance unit i i i : i = 0.45 38.7298 3 + 0.001 ( 38.7298 ) = 0.45 ( 3.3833 ) + 0.0387 = 1.5225 + 0.0387 = 1.5612 μ m i = 0.45\sqrt[3]{38.7298} + 0.001(38.7298) = 0.45(3.3833) + 0.0387 = 1.5225 + 0.0387 = 1.5612\;\mu\text{m} i = 0.45 3 38.7298 + 0.001 ( 38.7298 ) = 0.45 ( 3.3833 ) + 0.0387 = 1.5225 + 0.0387 = 1.5612 μ m
Hole Tolerance ( I T 7 IT7 I T 7 ) and Limits: I T 7 = 16 i = 16 × 1.5612 = 24.98 μ m ≈ 0.025 mm IT7 = 16i = 16 \times 1.5612 = 24.98\;\mu\text{m} \approx 0.025\text{ mm} I T 7 = 16 i = 16 × 1.5612 = 24.98 μ m ≈ 0.025 mm
For H H H -hole, fundamental deviation E I = 0 EI = 0 E I = 0 . Therefore: L L hole = 50.000 mm LL_{\text{hole}} = 50.000\text{ mm} L L hole = 50.000 mm U L hole = 50.000 + 0.025 = 50.025 mm UL_{\text{hole}} = 50.000 + 0.025 = 50.025\text{ mm} U L hole = 50.000 + 0.025 = 50.025 mm
Shaft Tolerance ( I T 6 IT6 I T 6 ), Fundamental Deviation, and Limits: I T 6 = 10 i = 10 × 1.5612 = 15.61 μ m ≈ 0.016 mm IT6 = 10i = 10 \times 1.5612 = 15.61\;\mu\text{m} \approx 0.016\text{ mm} I T 6 = 10 i = 10 × 1.5612 = 15.61 μ m ≈ 0.016 mm
Fundamental deviation for shaft g g g ( e s es es ): e s = − 2.5 ( 38.7298 ) 0.34 = − 2.5 ( 3.468 ) = − 8.67 μ m ≈ − 0.009 mm es = -2.5(38.7298)^{0.34} = -2.5(3.468) = -8.67\;\mu\text{m} \approx -0.009\text{ mm} es = − 2.5 ( 38.7298 ) 0.34 = − 2.5 ( 3.468 ) = − 8.67 μ m ≈ − 0.009 mm U L shaft = 50.000 + e s = 50.000 − 0.009 = 49.991 mm UL_{\text{shaft}} = 50.000 + es = 50.000 - 0.009 = 49.991\text{ mm} U L shaft = 50.000 + es = 50.000 − 0.009 = 49.991 mm L L shaft = U L shaft − I T 6 = 49.991 − 0.016 = 49.975 mm LL_{\text{shaft}} = UL_{\text{shaft}} - IT6 = 49.991 - 0.016 = 49.975\text{ mm} L L shaft = U L shaft − I T 6 = 49.991 − 0.016 = 49.975 mm
Clearance Calculations: Minimum Clearance = L L hole − U L shaft = 50.000 − 49.991 = + 0.009 mm = 9 μ m \text{Minimum Clearance} = LL_{\text{hole}} - UL_{\text{shaft}} = 50.000 - 49.991 = +0.009\text{ mm} = 9\;\mu\text{m} Minimum Clearance = L L hole − U L shaft = 50.000 − 49.991 = + 0.009 mm = 9 μ m Maximum Clearance = U L hole − L L shaft = 50.025 − 49.975 = + 0.050 mm = 50 μ m \text{Maximum Clearance} = UL_{\text{hole}} - LL_{\text{shaft}} = 50.025 - 49.975 = +0.050\text{ mm} = 50\;\mu\text{m} Maximum Clearance = U L hole − L L shaft = 50.025 − 49.975 = + 0.050 mm = 50 μ m
5. Taylor's Principle of Limit Gauge Design
Fixed limit gauges (plug gauges for holes, snap/ring gauges for shafts) provide fast, Go/No-Go inspection on the assembly floor without reading scales. TAYLOR'S GAUGE PRINCIPLE
- -----------------------
- GO GAUGE NO-GO GAUGE
- Checks Maximum Material - Checks Least Material
- Condition (MMC) Condition (LMC)
- Checks Form & Assembly - Checks Individual
- (Full contour/length) Dimension (Point/Line)
- Material Conditions
Maximum Material Condition (MMC): The condition where a feature contains the maximum volume of material:
For a Hole : MMC = Minimum Hole Size ( L L hole ) \text{MMC} = \text{Minimum Hole Size} (LL_{\text{hole}}) MMC = Minimum Hole Size ( L L hole )
For a Shaft : MMC = Maximum Shaft Size ( U L shaft ) \text{MMC} = \text{Maximum Shaft Size} (UL_{\text{shaft}}) MMC = Maximum Shaft Size ( U L shaft )
Least Material Condition (LMC): The condition where a feature contains the minimum volume of material:
For a Hole : LMC = Maximum Hole Size ( U L hole ) \text{LMC} = \text{Maximum Hole Size} (UL_{\text{hole}}) LMC = Maximum Hole Size ( U L hole )
For a Shaft : LMC = Minimum Shaft Size ( L L shaft ) \text{LMC} = \text{Minimum Shaft Size} (LL_{\text{shaft}}) LMC = Minimum Shaft Size ( L L shaft )
Taylor's Golden Rules
The GO Gauge: Must be designed to check the feature at its Maximum Material Condition (MMC) and check as many dimensions (full length, roundness, straightness) simultaneously as possible. It must enter the hole or pass over the shaft freely.
The NO-GO Gauge: Must be designed to check the feature at its Least Material Condition (LMC) and check only a single dimension (e.g., pin point contact or narrow blades) to prevent false acceptance due to out-of-roundness. It must not enter the hole or pass over the shaft.
Gauge Tolerances and Wear Allowance
Gauge Maker's Tolerance: Allocated as 10 % 10\% 10% of the work tolerance ( 0.10 × T work 0.10 \times T_{\text{work}} 0.10 × T work ).
Wear Allowance: Applied only to the GO gauge (as it rubs against every inspected component). A wear allowance of 5 % 5\% 5% to 10 % 10\% 10% of gauge tolerance is placed on the GO gauge within the work tolerance zone in the direction of wear.
- 6. Linear and Angular Metrology Instruments
- Linear Metrology
Vernier Calipers: Least Count ( L C LC L C ) is given by: L C = 1 Main Scale Division (MSD) − 1 Vernier Scale Division (VSD) = 1 MSD n LC = 1\text{ Main Scale Division (MSD)} - 1\text{ Vernier Scale Division (VSD)} = \frac{1\text{ MSD}}{n} L C = 1 Main Scale Division (MSD) − 1 Vernier Scale Division (VSD) = n 1 MSD For standard metric calipers with 1 MSD = 1 mm 1\text{ MSD} = 1\text{ mm} 1 MSD = 1 mm and 50 divisions on the vernier scale: L C = 1 / 50 = 0.02 mm LC = 1/50 = 0.02\text{ mm} L C = 1/50 = 0.02 mm .
Micrometer: Works on the principle of a precision nut and screw: L C = Pitch of Spindle Screw Total Number of Thimble Divisions = 0.5 mm 50 = 0.01 mm LC = \frac{\text{Pitch of Spindle Screw}}{\text{Total Number of Thimble Divisions}} = \frac{0.5\text{ mm}}{50} = 0.01\text{ mm} L C = Total Number of Thimble Divisions Pitch of Spindle Screw = 50 0.5 mm = 0.01 mm
Slip Gauges (Johannsen Gauges): Ultra-precision hardened steel or tungsten carbide blocks with mirror-finish parallel faces. Adhesion occurs via the wringing phenomenon (molecular attraction combined with a micro-thin oil layer). Calibration grades follow ISO 3650: Grade 00 (Reference master), Grade 0 (Calibration), Grade I (Inspection), Grade II (Workshop).
Angular Metrology: Sine Bar
A sine bar consists of a high-grade steel bar with two precision cylindrical rollers of equal diameter d d d set at an exact center distance L L L (typically 100 mm , 200 mm , 100\text{ mm}, 200\text{ mm}, 100 mm , 200 mm , or 300 mm 300\text{ mm} 300 mm ). Setting a stack of slip gauges of height h h h under one roller establishes an angle θ \theta θ : sin θ = h L ⟹ θ = arcsin ( h L ) \sin\theta = \frac{h}{L} \implies \theta = \arcsin\left(\frac{h}{L}\right) sin θ = L h ⟹ θ = arcsin ( L h ) +-----------------------+ <-- Workpiece Top Face (Horizontal)
- / /
- / SINE BAR /
- (O)===+=======================+===(O)
- | |
- Height |
- (h) Datum
- | Surface
- +-------+
- | Slip |
- | Gauges|
- +-------+-----------------------------------
- Sensitivity and Error Analysis of Sine Bar
Differentiating sin θ = h / L \sin\theta = h/L sin θ = h / L with respect to θ \theta θ : cos θ d θ = d h L = d h h / sin θ ⟹ d θ = tan θ ( d h h ) \cos\theta\,d\theta = \frac{dh}{L} = \frac{dh}{h/\sin\theta} \implies d\theta = \tan\theta\left(\frac{dh}{h}\right) cos θ d θ = L d h = h / sin θ d h ⟹ d θ = tan θ ( h d h )
For angles θ > 45 ∘ \theta > 45^{\circ} θ > 4 5 ∘ , tan θ > 1 \tan\theta > 1 tan θ > 1 and increases asymptotically toward infinity as θ → 90 ∘ \theta \to 90^{\circ} θ → 9 0 ∘ . A minute error in slip gauge height d h dh d h produces a massive angular error d θ d\theta d θ .
Hence, sine bars are strictly limited to angles ≤ 45 ∘ \le 45^{\circ} ≤ 4 5 ∘ in precision metrology .
Autocollimator and Clinometer
Autocollimator: An optical instrument that projects a parallel beam of collimated light onto a plane reflector and measures the angular tilt of the reflected beam via an eyepiece micrometer or CCD sensor. Used to check straightness, flatness of machine beds, and small angular deflections with resolution down to 0.1 arc-second 0.1\text{ arc-second} 0.1 arc-second .
Clinometer: An instrument utilizing a precision circular scale coupled to a spirit level or pendulum to measure absolute inclination angles of inclined surfaces over 0 ∘ 0^{\circ} 0 ∘ to 360 ∘ 360^{\circ} 36 0 ∘ .
7. Surface Metrology and Roughness Parameters
Machined surfaces consist of two distinct deviations from the nominal geometry:
Waviness (Secondary Texture): Long-wavelength periodic irregularities caused by machine vibrations, chatter, or workpiece deflection.
Roughness (Primary Texture): Short-wavelength irregularities caused by the cutting tool feed marks, built-up edge fragmentation, and shear fracture. Peak ^ Roughness Profile y(x)
- | /\ /\ /\
- |------/--\--------/--\------/--\---- Center Line (Mean Line)
- | / \ /\ / \ / \
- |____/______\/__\/______\__/______\__
- Valley Sampling Length (L)
- Mathematical Definitions of Roughness Parameters
Arithmetical Mean Deviation ( R a R_a R a / CLA - Center Line Average): R a = 1 L ∫ 0 L ∣ y ( x ) ∣ d x ≈ ∑ i = 1 n ∣ y i ∣ n R_a = \frac{1}{L} \int_0^L |y(x)|\,dx \approx \frac{\sum_{i=1}^n |y_i|}{n} R a = L 1 ∫ 0 L ∣ y ( x ) ∣ d x ≈ n ∑ i = 1 n ∣ y i ∣
Root Mean Square Roughness ( R q R_q R q / RMS): R q = 1 L ∫ 0 L y 2 ( x ) d x ≈ ∑ i = 1 n y i 2 n R_q = \sqrt{\frac{1}{L}\int_0^L y^2(x)\,dx} \approx \sqrt{\frac{\sum_{i=1}^n y_i^2}{n}} R q = L 1 ∫ 0 L y 2 ( x ) d x ≈ n ∑ i = 1 n y i 2 For a pure sinusoidal roughness profile, R q = π 2 2 R a ≈ 1.11 R a R_q = \frac{\pi}{2\sqrt{2}} R_a \approx 1.11 R_a R q = 2 2 π R a ≈ 1.11 R a .
Ten-Point Height of Irregularities ( R z R_z R z ): The average difference between the 5 highest peaks and 5 deepest valleys within the sampling length: R z = ( y p 1 + y p 2 + y p 3 + y p 4 + y p 5 ) − ( y v 1 + y v 2 + y v 3 + y v 4 + y v 5 ) 5 R_z = \frac{(y_{p1} + y_{p2} + y_{p3} + y_{p4} + y_{p5}) - (y_{v1} + y_{v2} + y_{v3} + y_{v4} + y_{v5})}{5} R z = 5 ( y p 1 + y p 2 + y p 3 + y p 4 + y p 5 ) − ( y v 1 + y v 2 + y v 3 + y v 4 + y v 5 )
Maximum Peak-to-Valley Height ( R t R_t R t or h max h_{\max} h m a x ): The vertical distance between the highest peak crest and lowest valley trough.
Theoretical Surface Roughness in Machining
For a Single-Point Turning Tool with Nose Radius R nose R_{\text{nose}} R nose and Feed f f f : R t = f 2 8 R nose R_t = \frac{f^2}{8 R_{\text{nose}}} R t = 8 R nose f 2 The corresponding theoretical center-line average roughness is: R a ≈ R t 4 = f 2 32 R nose R_a \approx \frac{R_t}{4} = \frac{f^2}{32 R_{\text{nose}}} R a ≈ 4 R t = 32 R nose f 2 (where f f f is in mm/rev \text{mm/rev} mm/rev and R nose R_{\text{nose}} R nose is in mm \text{mm} mm ) .
For a Sharp Tool (Zero Nose Radius, Side Cutting Edge Angle C s C_s C s , End Cutting Edge Angle C e C_e C e ): R t = f tan C s + cot C e R_t = \frac{f}{\tan C_s + \cot C_e} R t = tan C s + cot C e f R a = R t 4 = f 4 ( tan C s + cot C e ) R_a = \frac{R_t}{4} = \frac{f}{4(\tan C_s + \cot C_e)} R a = 4 R t = 4 ( tan C s + cot C e ) f