Study guide
12.6 Behaviour of Ideal & Real Gases and Equations of State
Coal India Management Trainee CIL MT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: CIL MT Exam Overview & Coal Sector Landscape
1.1 CIL MT Exam Pattern, Marking Scheme & Strategy 1.2 Coal India Limited: Corporate Structure, Maharatna Status & Subsidiaries 1.3 Indian Coal Mining Sector, Energy Mix & Environmental Regulations
2 Chapter 2: Paper-I General Awareness, Polity & Current Affairs
2.1 Indian Constitution, Governance & Statutory Bodies 2.2 Indian Economy, Union Budget & Economic Planning 2.3 Indian Geography, Mineral Belts & Environmental Ecology 2.4 Modern Indian History, Freedom Struggle & Cultural Heritage 2.5 General Science: Physics, Chemistry & Biology Fundamentals 2.6 Inventions, Discoveries & Scientific-Technological Development 2.7 Uses of Internet, Computer Awareness & Digital Governance 2.8 National & International Organisations 2.9 Awards, Honours & Sports 2.10 Books & Authors, Important Monuments & Places of India 2.11 Ports, Power Plants & Infrastructure of India 2.12 Climate Change, SDGs, National Parks & Wildlife Sanctuaries 2.13 Flagship Government Programmes & Current Affairs Method 2.14 World Physical, Social & Economic Geography
3 Chapter 3: Paper-I Reasoning & Logical Ability
3.1 Series Completion, Coding-Decoding & Semantic Analogies 3.2 Syllogisms, Logical Deduction & Venn Diagrams 3.3 Seating Arrangements, Linear/Circular Alignments & Puzzles 3.4 Direction Sense, Blood Relations & Order/Ranking 3.5 Alphabetical & Alphanumeric Series 3.6 Statement & Conclusions, Statement & Arguments 3.7 Clocks & Calendars 3.8 Cubes, Dice & Figure Counting 3.9 Mirror Images, Water Images, Embedded Figures & Non-Verbal Series 3.10 Decision Making & Data Analysis in Reasoning
4 Chapter 4: Paper-I Numerical Ability & Quantitative Aptitude
4.1 Arithmetic Foundations: Percentages, Profit & Loss, Ratio & Proportion 4.2 Averages, Simple/Compound Interest, Alligations & Mixtures 4.3 Time & Work, Pipes & Cisterns, Time, Speed & Distance 4.4 Algebra, Mensuration, Geometry & Data Interpretation (DI) 4.5 Number System, LCM, HCF & Decimal Fractions 4.6 Surds, Indices & Simplification 4.7 Problems on Ages 4.8 Boats & Streams and Problems on Trains 4.9 Permutations & Combinations 4.10 Probability for Quantitative Aptitude
5 Chapter 5: Paper-I General English & Verbal Ability
5.1 English Grammar, Error Spotting & Sentence Correction 5.2 Vocabulary Building: Synonyms, Antonyms, Idioms & Phrases 5.3 Reading Comprehension, Cloze Tests & Para Jumbles 5.4 Fill in the Blanks, Cloze Passages & Sentence Completion 5.5 Jumbled Sentences & Sentence Improvement
6 Chapter 6: Paper-II Engineering Mathematics
6.1 Matrix Algebra, Rank & Systems of Linear Equations 6.2 Eigenvalues, Eigenvectors & the Cayley-Hamilton Theorem 6.3 Limits, Continuity, Differentiability & Mean Value Theorems 6.4 Maxima-Minima, Indeterminate Forms & Taylor Series 6.5 Definite, Improper, Double & Triple Integrals 6.6 Partial Derivatives, Total Derivative & Multivariable Optimisation 6.7 First-Order Differential Equations: Linear & Non-Linear 6.8 Higher-Order Linear Differential Equations & Engineering Applications 6.9 Laplace Transforms & Transfer-Function Methods 6.10 Probability, Conditional Probability & Bayes' Theorem 6.11 Random Variables, Distributions & Descriptive Statistics 6.12 Numerical Methods: Root Finding, Integration & ODE Solvers
7 Chapter 7: Paper-II Engineering Mechanics & Statics-Dynamics
7.1 Force Systems, Coplanar Equilibrium & Lami's Theorem 7.2 Plane Trusses, Friction Mechanics & Screws/Wedges 7.3 Centroids, Center of Gravity & Moment of Inertia 7.4 Kinematics, Kinetics of Particles & Rigid Body Dynamics 7.5 Virtual Work & Lagrange's Equation 7.6 Rolling Friction, Belt-Pulley Drives, Brakes, Clutches & Vehicle Dynamics
8 Chapter 8: Paper-II Mechanics of Materials & Structural Integrity
8.1 Simple Stresses, Strains, Elastic Moduli & Thermal Stresses 8.2 Principal Stresses, Strain Energy & Mohr's Circle 8.3 Shear Force & Bending Moment Diagrams, Beam Bending & Shear Stresses 8.4 Torsion of Circular Shafts, Springs & Column Buckling 8.5 Thin Cylinders, Spheres & Thick-Walled Pressure Vessels 8.6 Deflection of Beams: Double Integration, Macaulay & Moment-Area 8.7 Shear Centre & Unsymmetrical Bending 8.8 Strain Gauges, Rosettes & Experimental Stress Analysis 8.9 Mechanical Testing: Universal Testing Machine, Hardness & Impact
9 Chapter 9: Paper-II Theory of Machines & Mechanical Vibrations
9.1 Simple Mechanisms, Kinematic Inversions & Velocity/Acceleration Diagrams 9.2 Cams & Followers, Toothed Gearing & Epicyclic Gear Trains 9.3 Flywheels, Centrifugal/Inertia Governors & Rotor Balancing 9.4 Free, Damped & Forced Single-Degree-of-Freedom Vibrations 9.5 Gyroscopic Couple & Gyroscopic Effects
10 Chapter 10: Paper-II Machine Design & Failure Theories
10.1 Static Failure Theories & Variable/Fatigue Loading 10.2 Design of Threaded Fasteners, Welded & Riveted Joints 10.3 Design of Shafts, Keys, Couplings & Rolling/Sliding Bearings 10.4 Design of Spur, Helical, Bevel & Worm Gears 10.5 Design of Helical, Leaf & Torsion Springs 10.6 Design of Brakes & Clutches: Energy, Lining Pressure & Heat
11 Chapter 11: Paper-II Fluid Mechanics & Hydraulic Machinery
11.1 Fluid Properties, Hydrostatic Forces & Buoyancy 11.2 Fluid Kinematics, Continuity & Bernoulli's Equation 11.3 Viscous Flow in Pipes, Boundary Layer & Minor Losses 11.4 Hydraulic Turbines, Centrifugal & Reciprocating Pumps 11.5 Dimensional Analysis, Similitude & Model Testing 11.6 Control-Volume Analysis: Continuity, Momentum & Energy
12 Chapter 12: Paper-II Thermodynamics, Thermal Cycles & Turbomachinery
12.1 Fundamental Concepts, First & Second Laws of Thermodynamics 12.2 Entropy, Availability, Exergy & Properties of Pure Substances 12.3 Air-Standard Gas Power Cycles: Otto, Diesel, Dual & Brayton 12.4 Vapour Power Cycles: Ideal, Reheat & Regenerative Rankine Cycles 12.5 Thermodynamic Relations: Maxwell, Clausius-Clapeyron & Joule-Thomson 12.6 Behaviour of Ideal & Real Gases and Equations of State 12.7 Air & Gas Compressors: Reciprocating, Rotary & Multi-Stage 12.8 Steam & Gas Turbines: Impulse, Reaction & Velocity Diagrams
13 Chapter 13: Paper-II Heat Transfer, Refrigeration & Air Conditioning
13.1 Steady & Unsteady Conduction, Extended Surfaces (Fins) 13.2 Forced/Natural Convection, Radiation & Heat Exchanger LMTD/NTU 13.3 Vapour Compression & Vapour Absorption Refrigeration Systems 13.4 Psychrometric Properties, Processes & Air Conditioning Systems 13.5 Gas Refrigeration, Heat Pump Cycles & Cryogenics
14 Chapter 14: Paper-II Materials Science, Metallurgy & Manufacturing Technology
14.1 Crystal Structures, Phase Diagrams & Iron-Iron Carbide Equilibrium 14.2 Heat Treatment Processes & Engineering Alloy Steels 14.3 Casting Processes, Metal Forming & Welding Metallurgy 14.4 Metal Cutting Mechanics, Tool Life & Machine Tools 14.5 Plastic Deformation, Yield Criteria & Load Estimation in Bulk Forming 14.6 Sheet Metal Forming: Shearing, Bending & Deep Drawing 14.7 Powder Metallurgy 14.8 Brazing, Soldering & Adhesive Bonding 14.9 Non-Traditional Machining: EDM, ECM, USM, AJM, LBM & EBM 14.10 Abrasive Machining, Grinding & Superfinishing 14.11 Principles of Work Holding, Jigs & Fixtures 14.12 Economics of Machining & Tool Life Optimisation
15 Chapter 15: Paper-II Metrology, Quality Control & Industrial Engineering / OR
15.1 Limits, Fits, Tolerances, Gauges & Surface Metrology 15.2 Production Planning, Forecasting & Inventory Control Models 15.3 Operations Research: Linear Programming & Transportation/Assignment 15.4 Project Management: CPM, PERT, Network Analysis & Crashing 15.5 Comparators & Interferometry 15.6 Coordinate Measuring Machines & Machine Tool Alignment Testing 15.7 Computer Integrated Manufacturing: CAD/CAM & Integration Tools 15.8 NC/CNC Machines & CNC Part Programming 15.9 Material Requirements Planning, Scheduling & Sequencing 15.10 Queuing Theory & Simple Queuing Models 15.11 Network Flow Models: Shortest Route, Maximal Flow & Spanning Tree
12.6 Behaviour of Ideal & Real Gases and Equations of State
Key Takeaways Explain This Topic AI
Behaviour of ideal and real gases is named explicitly in the Thermodynamics bullet of the CIL Mechanical Paper-II syllabus.
The compressibility factor Z equals pv divided by RT and is exactly one for an ideal gas, with departure from unity measuring real-gas behaviour.
The van der Waals equation adds a term a over v squared for intermolecular attraction and subtracts b from the volume for finite molecular size.
The principle of corresponding states holds that all gases have approximately the same compressibility factor when compared at the same reduced pressure and reduced temperature.
Last updated: August 2026
- When the Ideal Gas Law Fails
- The ideal gas equation p v = R T pv = RT p v = RT
assumes molecules are point masses with no intermolecular forces. Both assumptions fail when molecules are pressed close together or move slowly, that is at high pressure or low temperature , and especially near the saturation line .
For a Management Trainee this is not academic. Compressed air receivers at 10 bar, refrigerants throughout the vapour-compression cycle, and coal-bed methane stored at pressure all depart measurably from ideal behaviour.
The rule of thumb is that the ideal gas law is acceptable when the pressure is well below the critical pressure and the temperature is well above the critical temperature, typically taken as T > 2 T c T > 2T_c T > 2 T c or p < 0.1 p c p < 0.1 p_c p < 0.1 p c .
The Compressibility Factor
The departure is quantified by a single dimensionless correction: Z = p v R T \boxed{Z = \frac{pv}{RT}} Z = RT p v
- Z Z Z Interpretation
- Z = 1 Z = 1 Z = 1 Ideal behaviour
- Z < 1 Z < 1 Z < 1 Attractive forces dominate; actual volume smaller than ideal
- Z > 1 Z > 1 Z > 1 Repulsive forces and finite molecular volume dominate; actual volume larger
At moderate pressures Z Z Z is typically less than one, because attraction pulls molecules together. At very high pressures the finite size of the molecules dominates and Z Z Z exceeds one. For hydrogen and helium, whose intermolecular attraction is very weak, Z Z Z exceeds one over almost the whole practical range.
The van der Waals Equation
The first and most-examined real-gas equation modifies both terms of the ideal law: ( p + a v 2 ) ( v − b ) = R T \boxed{\left(p + \frac{a}{v^2}\right)\left(v - b\right) = RT} ( p + v 2 a ) ( v − b ) = RT
Term Corrects for Reasoning
a / v 2 a/v^2 a / v 2 added to pressure Intermolecular attraction Molecules near the wall are pulled inward, so the measured pressure is less than the ideal kinetic pressure
b b b subtracted from volume Finite molecular volume The molecules themselves occupy space, reducing the free volume available
The constant b b b is called the co-volume and is roughly four times the actual volume of the molecules.
Critical-point constants
At the critical point the isotherm has a point of inflection with a horizontal tangent, so ( ∂ p ∂ v ) T c = 0 and ( ∂ 2 p ∂ v 2 ) T c = 0 \left(\frac{\partial p}{\partial v}\right)_{T_c} = 0 \quad\text{and}\quad \left(\frac{\partial^2 p}{\partial v^2}\right)_{T_c} = 0 ( ∂ v ∂ p ) T c = 0 and ( ∂ v 2 ∂ 2 p ) T c = 0
Applying both conditions to the van der Waals equation yields v c = 3 b , T c = 8 a 27 R b , p c = a 27 b 2 v_c = 3b, \qquad T_c = \frac{8a}{27Rb}, \qquad p_c = \frac{a}{27b^2} v c = 3 b , T c = 27 R b 8 a , p c = 27 b 2 a
and inverting, a = 27 R 2 T c 2 64 p c , b = R T c 8 p c a = \frac{27R^2T_c^2}{64p_c}, \qquad b = \frac{RT_c}{8p_c} a = 64 p c 27 R 2 T c 2 , b = 8 p c R T c
The most striking consequence is the critical compressibility factor : Z c = p c v c R T c = 3 8 = 0.375 Z_c = \frac{p_c v_c}{RT_c} = \frac{3}{8} = 0.375 Z c = R T c p c v c = 8 3 = 0.375
This is a universal constant for all van der Waals gases, independent of a a a and b b b . Real substances give values between about 0.23 and 0.31, so the van der Waals equation overestimates Z c Z_c Z c — accurate qualitatively but not quantitatively. That combination of conceptual correctness and quantitative imprecision is exactly why it survives in teaching but not in design.
Other Equations of State
Equation Form Comment
Redlich-Kwong p = R T v − b − a T 1 / 2 v ( v + b ) p = \dfrac{RT}{v-b} - \dfrac{a}{T^{1/2}v(v+b)} p = v − b RT − T 1/2 v ( v + b ) a Better accuracy than van der Waals; two constants
Berthelot ( p + a T v 2 ) ( v − b ) = R T \left(p + \dfrac{a}{Tv^2}\right)(v-b) = RT ( p + T v 2 a ) ( v − b ) = RT Temperature-dependent attraction term
Dieterici p ( v − b ) = R T e − a / R T v p(v-b) = RT\,e^{-a/RTv} p ( v − b ) = RT e − a / RT v Good near the critical point
Virial p v R T = 1 + B v + C v 2 + ⋯ \dfrac{pv}{RT} = 1 + \dfrac{B}{v} + \dfrac{C}{v^2} + \cdots RT p v = 1 + v B + v 2 C + ⋯ Series expansion with theoretical foundation
- Beattie-Bridgeman Five constants Accurate to about 0.8 times critical density
- Benedict-Webb-Rubin Eight constants Accurate to about 2.5 times critical density
The virial equation deserves note because its coefficients have a statistical-mechanical meaning: the second virial coefficient B B B describes two-molecule interactions, C C C three-molecule interactions, and so on. Truncating after B B B is adequate at moderate pressures.
The Principle of Corresponding States
Define reduced properties by dividing each by its critical value: p r = p p c , T r = T T c , v r = v v c p_r = \frac{p}{p_c}, \qquad T_r = \frac{T}{T_c}, \qquad v_r = \frac{v}{v_c} p r = p c p , T r = T c T , v r = v c v
Substituting into the van der Waals equation eliminates a a a and b b b entirely and gives ( p r + 3 v r 2 ) ( 3 v r − 1 ) = 8 T r \left(p_r + \frac{3}{v_r^2}\right)\left(3v_r - 1\right) = 8T_r ( p r + v r 2 3 ) ( 3 v r − 1 ) = 8 T r
No substance-specific constants remain. This is the mathematical statement of the principle of corresponding states :
All gases, when compared at the same reduced pressure and reduced temperature, have approximately the same compressibility factor.
The generalised compressibility chart
The practical consequence is a single chart of Z Z Z against p r p_r p r with T r T_r T r as parameter, usable for any gas. The procedure is:
Look up p c p_c p c and T c T_c T c for the gas.
Compute p r p_r p r and T r T_r T r .
Read Z Z Z from the chart.
Use p v = Z R T pv = ZRT p v = ZRT .
When the volume is known but not the pressure, the pseudo-reduced specific volume is used instead: v r ′ = v p c R T c v_r' = \frac{v\,p_c}{R\,T_c} v r ′ = R T c v p c
Worked example
Find the specific volume of carbon dioxide at 8 MPa and 320 K. For carbon dioxide, p c = 7.39 p_c = 7.39 p c = 7.39 MPa, T c = 304.2 T_c = 304.2 T c = 304.2 K and R = 0.1889 R = 0.1889 R = 0.1889 kJ/kg K. p r = 8 7.39 = 1.08 , T r = 320 304.2 = 1.05 p_r = \frac{8}{7.39} = 1.08, \qquad T_r = \frac{320}{304.2} = 1.05 p r = 7.39 8 = 1.08 , T r = 304.2 320 = 1.05
From the generalised chart at these reduced conditions, Z ≈ 0.30 Z \approx 0.30 Z ≈ 0.30 . Then v = Z R T p = 0.30 × 0.1889 × 320 8000 = 2.27 × 10 − 3 m 3 / kg v = \frac{ZRT}{p} = \frac{0.30\times0.1889\times320}{8000} = 2.27\times10^{-3} \text{ m}^3/\text{kg} v = p ZRT = 8000 0.30 × 0.1889 × 320 = 2.27 × 1 0 − 3 m 3 / kg
The ideal gas law would have given 7.56 × 10 − 3 7.56\times10^{-3} 7.56 × 1 0 − 3 m 3 ^3 3 /kg — an error of more than 230% . This is exactly the region, just above the critical point, where ideal-gas assumptions are least defensible, and it is the operating region of supercritical carbon dioxide systems.
Behaviour Near Saturation
A useful qualitative picture of Z Z Z against p r p_r p r :
At very low pressure ( p r → 0 p_r \to 0 p r → 0 ), Z → 1 Z \to 1 Z → 1 for all gases and all temperatures. Ideal behaviour is always recovered as pressure falls.
At high temperature ( T r > 2 T_r > 2 T r > 2 ), Z Z Z stays near unity across a wide pressure range.
Near T r ≈ 1 T_r \approx 1 T r ≈ 1 , Z Z Z dips sharply, reaching values as low as 0.2 to 0.3 near the critical pressure. This is the worst region for the ideal gas assumption.
At very high p r p_r p r , Z Z Z rises above unity as repulsion dominates.
Practical Note
For design work, tabulated property data — steam tables, refrigerant tables, software libraries — are always preferred to any equation of state, because they are fitted directly to measurement. Equations of state are used where tables do not exist, in computational work where a closed form is needed, and in examination questions where the compressibility chart is the intended route.