Study guide
11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems
DG Shipping General Purpose Rating Final Exam India
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction to Shipping, Ship Structure & Organization
1.1 Maritime Trade, Ship Types & Principal Dimensions 1.2 Shipboard Organization, Ranks & Trainee GP Rating Duties 1.3 Hull Structure, Compartments & Watertight Openings 1.4 Computer Operation, Shipboard IT Systems & Digital Basics
2 Chapter 2: Navigation Basics, Bridge Equipment & Watchkeeping
2.1 Bridge Layout, Compass, Helmsman Duties & Steering Orders 2.2 Lookout Duties, Night Vision & STCW Bridge Watchkeeping 2.3 IALA Maritime Buoyage System (Region A) & Basic COLREGs Lights/Shapes
3 Chapter 3: Anchor Work, Mooring Operations & Tug Safety
3.1 Ground Tackle: Anchors, Cables, Windlass & Hawse Pipe 3.2 Mooring Equipment, Lines & Deck Fittings 3.3 Mooring & Unmooring Operations, Snap-Back Zones & Tug Safety
4 Chapter 4: Cargo Handling Gear, Stowage & Hold Maintenance
4.1 Cargo Handling Appliances: Derricks, Cranes & Safe Working Load (SWL) 4.2 Cargo Hold Preparation, Dunnage & Hold Cleaning 4.3 Container Cargo, Bulk Cargoes & IMDG Code Awareness
5 Chapter 5: Seamanship, Ropes, Rigging & Deck Maintenance
5.1 Natural, Synthetic & Wire Ropes: Care, Coiling & Splicing 5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging 5.3 Deck Maintenance: Chipping, Wire-Brushing, Painting & Working Aloft/Overside
6 Chapter 6: Shipboard Safety, Safe Working Practices & Permits
6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard 6.2 Permit to Work Systems & Enclosed Space Entry 6.3 Hot Work Precautions, Electrical Safety on Deck & Gangway Watch
7 Chapter 7: STCW Basic Safety, Firefighting & Life Saving Appliances
7.1 Life-Saving Appliances: Lifejackets, Immersion Suits & Lifebuoys 7.2 Survival Craft: Lifeboats, Liferafts & Launching Appliances 7.3 Basic Firefighting Principles, Fire Triangle & Portable Extinguishers 7.4 Elementary First Aid, CPR, Bleeding Control & Medical Emergency Response
8 Chapter 8: Marine Pollution Prevention & MARPOL Regulations
8.1 MARPOL Overview & Annex I: Oil Pollution Prevention 8.2 MARPOL Annex V: Garbage Management & Shipboard Waste 8.3 Bunkering Procedures, SOPEP & Spill Response
9 Chapter 9: Engine Room Familiarization, Watchkeeping & Safety
9.1 Engine Room Layout, Bilges, Tank Tops & Trainee Ratings Duties 9.2 Engine Room Instrumentation, Alarms & Emergency Escapes 9.3 Quick-Closing Valves, Emergency Stops & Fire Dampers
10 Chapter 10: Marine Diesel Engines: Cycles, Components & Systems
10.1 Two-Stroke & Four-Stroke Marine Diesel Operating Principles 10.2 Main Engine Structural Components & Moving Parts 10.3 Engine Support Systems: Fuel Oil, Lubricating Oil & Starting Air 10.4 Engine Cooling Water Systems & Scavenge Fires
11 Chapter 11: Marine Auxiliary Machinery, Heat Exchangers & Boilers
11.1 Air Compressors, Compressed Air Receivers & Centrifugal Purifiers 11.2 Fresh Water Generators (Evaporators) & Heat Exchangers 11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems 11.4 Domestic Services, Refrigeration, Air Conditioning & Sewage Treatment
12 Chapter 12: Marine Pumps, Piping Systems, Valves & Steering Gear
12.1 Centrifugal & Positive Displacement Marine Pumps 12.2 Valves, Filters, Strainers & Pipeline Identification 12.3 Bilge, Ballast & Oily Water Separator (OWS) Systems 12.4 Steering Gear Systems & Emergency Steering Procedures 12.5 Shipboard Plumbing Repairs, Pipe Clamping & Pipeline Maintenance
13 Chapter 13: Workshop Tools, Fitting, Hot Work & Electrical Safety
13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement 13.2 Power Tools, Grinding, Drilling & Safe Workshop Operations 13.3 Gas Welding, Electric Arc Welding & Hot Work Safety 13.4 Electrical Safety, Isolation, LOTO & Hazards in Machinery Spaces 13.5 Lathe Machine Operations, Centering & Fabrication 13.6 Shipboard Carpentry, Woodworking & Cement Box Emergency Repairs
14 Chapter 14: Engine Room Firefighting, Fixed Systems & Emergency Response
14.1 Machinery Space Fire Hazards & Flammable Liquids Management 14.2 Fixed Fire-Extinguishing Systems: CO2, Water Mist & Hi-Expansion Foam 14.3 Emergency Procedures: Blackout, Flooding, Abandon Ship & Engine Room Safety Drills
11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems
Key Takeaways Explain This Topic AI
Marine auxiliary boilers provide essential steam (6-16 bar) for fuel tank heating, heavy fuel purifiers, cargo heating, and domestic hot water, utilizing water-tube, fire-tube, or composite configurations.
Exhaust gas economizers harness main engine exhaust heat (280-350°C) at sea to produce steam without burning fuel, requiring regular daily soot blowing to prevent soot fires.
Statutory SOLAS boiler mountings include normally two safety valves, two water-level indications (at least one direct gauge glass), blow-down valves, and automatic low-water fuel shut-off trips.
Boiler water treatment relies on chemical alkalinity control (pH 9.5-11.0), oxygen scavenging (sodium sulfite or hydrazine), and phosphate treatment to prevent scale and corrosion.
Surface blowdown removes floating oil and scum, while bottom blowdown expels precipitated sludge and manages Total Dissolved Solids (TDS) to prevent foaming and water carryover.
Last updated: November 2026
11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems
Steam systems are indispensable on motor merchant ships. Although primary propulsion is provided by large diesel engines, thermal energy in the form of low- and medium-pressure steam (typically 6 – 16 bar 6\text{--}16\text{ bar} 6 – 16 bar ) is constantly required to heat Heavy Fuel Oil (HFO) bunker tanks, settling tanks, and service tanks so the fuel remains fluid enough to be pumped. Steam is also required to preheat fuel prior to purifiers and main engine fuel injectors, heat liquid cargoes on product/chemical tankers, warm accommodation blocks in cold climates, and supply galley and domestic hot water.
1. Marine Auxiliary Boilers and Exhaust Gas Economizers +-----------------------------------------------------------------------------------------+
- | MARINE AUXILIARY BOILER TYPES |
- +-------------------+--------------------------------+------------------------------------+
- | Boiler Type | Water / Gas Configuration | Key Operational Characteristics |
- +-------------------+--------------------------------+------------------------------------+
- | **Auxiliary | Water and steam circulate | - Rapid steam raising (15-30 min) |
- | Water-Tube | inside high-pressure tubes; | - Handles high pressures (>16 bar) |
- | Boiler** | hot combustion gas surrounds | - Low water volume; highly sensitive|
- | | tube exteriors. | to feed water quality & scale. |
- +-------------------+--------------------------------+------------------------------------+
- | **Smoke-Tube / | Hot combustion gas passes | - Large water volume; excellent |
- | Fire-Tube | inside tubes; water completely | thermal buffer capacity. |
- | Boiler** | surrounds tubes in outer shell.| - Moderate pressure (6-10 bar). |
- | (e.g. Cochran) | | - Robust, tolerant of minor scale. |
- +-------------------+--------------------------------+------------------------------------+
- | **Composite | Combines oil-fired combustion | - Highly versatile for general cargo|
- | Boiler** | chamber and separate exhaust | - Uses main engine exhaust at sea; |
- | | gas tube bank in one shell. | burns oil in port/maneuvering. |
- +-------------------+--------------------------------+------------------------------------+
- Exhaust Gas Economizers (Waste Heat Recovery)
When a ship's main diesel engine runs at normal sea speed, exhaust gases entering the economizer after the turbocharger may typically be between 280 ∘ C 280^\circ\text{C} 28 0 ∘ C and 350 ∘ C 350^\circ\text{C} 35 0 ∘ C . Discharging these gases directly into the atmosphere represents immense wasted thermal energy.
An Exhaust Gas Economizer (often referred to as an exhaust gas boiler) is installed in the engine exhaust gas funnel casing. It consists of multiple banks of steel tubes (often fitted with external spiral steel fins or pins to increase surface area) connected to the auxiliary boiler steam-and-water circulation system:
Boiler water is continuously circulated by a boiler circulating pump from the auxiliary boiler steam drum through the economizer tube banks and returned as a steam-water mixture.
While steaming at sea, the economizer generates sufficient steam ( 7 – 8 bar 7\text{--}8\text{ bar} 7 – 8 bar ) to satisfy all shipboard heating demands without burning any fuel in the oil-fired auxiliary boiler burner. EXHAUST GAS ECONOMIZER SYSTEM
- GAS PATH: Main engine -> Turbocharger -> Economizer gas casing -> Funnel
- (Hot gas outside tubes)
- |
- Heat transferred
- v
- WATER PATH: Auxiliary boiler drum -> Circulating pump -> Economizer tubes
- ^ |
- +------- Steam-water mixture return ----+
- |
- Steam to ship's services
Gas and boiler water remain separated by the tube walls.
Soot Blowers and Economizer Fires
Main engine exhaust gas contains unburned carbon, lubricating oil residues, and sulfur compounds that deposit on economizer finned tubes as sticky soot . Soot insulates the tubes, reducing heat transfer and steam production; increasing deposits also increase the fire risk.
More critically, accumulated soot represents a severe fire hazard:
Soot Blowers : Motorized or manual rotating lances fitted with high-pressure steam nozzles (or compressed air nozzles) are installed within the tube banks. GP Ratings or watch engineers operate soot blowers daily or twice daily while the engine is running at steady sea load. High-pressure steam jets sweep across the tubes, dislodging soot deposits into the exhaust gas stream.
Soot Fires : If soot blowing is neglected, a high engine load or scavenge fire can ignite the dry soot deposit, causing an economizer soot fire . If temperatures exceed 1000 ∘ C 1000^\circ\text{C} 100 0 ∘ C , the steel tubes themselves can react with steam or water in an autocatalytic iron-water reaction ( 3 F e + 4 H 2 O → F e 3 O 4 + 4 H 2 3Fe + 4H_2O \to Fe_3O_4 + 4H_2 3 F e + 4 H 2 O → F e 3 O 4 + 4 H 2 ), producing explosive hydrogen gas and completely incinerating the economizer bundle.
Warning
Action in Event of Economizer Fire : Raise the alarm and inform the bridge so the main engine can be stopped and gas flow cut off. For an initial soot fire with intact tubes, maintain boiler-water circulation to cool them. Do not use steam or air soot blowers to fight the fire. Operate installed firefighting or water-washing equipment as directed by the maker. If tubes fail or a high-temperature iron fire develops, the Chief Engineer must follow the specific isolation, draining and firefighting procedure; do not improvise hose application or continue feeding leaking tubes.
2. Statutory Boiler Mountings and Safety Systems
Marine steam boilers require protective mountings under SOLAS and class rules. The following drawing shows a typical auxiliary boiler arrangement: TYPICAL AUXILIARY BOILER MOUNTINGS
- [Air Vent Valve] [Dual Safety Valves]
- | |
- +----------+---------+
- |
- =============================+=============================
- / STEAM DRUM / STEAM SPACE \
- | |
- | [Main Steam Stop Valve] [Pressure Gauge & Cock] |
- | (SDNR Valve to Steam Manifold) |
- | |
- | [Surface Blowdown Valve] [Two Independent Water] |
- | (Scum Valve for Oil/Foam) [Level Gauge Glasses ] |
- | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [With Remote Blowdowns] |
- | NORMAL WATER LEVEL |
- | =============================== |
- | |
- | [Feed Check Valves] [Low Water Level Alarm &] |
- | (Main & Auxiliary SDNR) [Burner Cut-Out Sensors ] |
- \ /
- =============================+=============================
- |
- [Bottom Blowdown Valve]
- (Drains Sludge & Sediment)
- Mandatory Boiler Mountings
Safety Valves (Dual Independent) :
SOLAS normally requires at least two safety valves of adequate capacity ; the Administration may approve one where adequate overpressure protection is provided. Valves connect directly to the steam space without intervening shut-off valves. Their combined capacity must discharge the maximum steam output within the approved accumulation limit.
Adjustment is protected by locked or sealed covers to prevent unauthorized changes to the spring setting.
External easing gear allows controlled lifting from a safe position. Test it at the pressure and interval specified by the maker and planned maintenance system; a weekly shipboard routine is not itself a SOLAS interval.
Water Level Indication :
For a boiler essential to ship safety that maintains a specified water level, SOLAS requires two means of level indication, at least one a direct-reading gauge glass . Two separate glasses are a common arrangement.
Protected by toughened plate glass shields to protect watchkeepers if a tubular glass bursts.
Fitted with upper steam isolation cock, lower water isolation cock, and a bottom drain cock.
Main Steam Stop Valve :
Heavy-duty screw-down non-return (SDNR) globe valve isolating the boiler from the ship's steam distribution header.
Feed Check Valves (Main and Auxiliary) :
Two independent feed water supply lines, each terminating in a screw-down non-return valve mounted on the boiler shell below the water line. The non-return valve prevents hot pressurized boiler water from surging back into feed pumps if a pump fails.
Surface Blowdown Valve (Scum Valve) :
Connected to an internal scum pan mounted just below the normal working water level. Opened periodically to skim off floating lubricating oil, foam, and suspended organic matter.
Bottom Blowdown Valve :
Connected to the lowest point of the boiler shell/water drum. Opened to purge heavy accumulated sludge, precipitated scale salts, and lower boiler water Total Dissolved Solids (TDS).
Air Vent Cock :
Mounted at the highest point of the steam space. Opened when filling boiler with water, opened when raising steam (to allow displaced air to escape until pure steam blows free), and opened when taking boiler out of service (to prevent vacuum collapse when cooling).
Low-Water Level Fuel Shut-Off (Burner Management System) :
Dual independent float-switch or electrode-type sensors. If water drops to the lowest permissible water level ( L W L LWL L W L ) , the burner management system shuts the fuel oil supply solenoid valve and sounds an alarm. The burner control system follows its approved shutdown sequence.
The Gauge Glass Blow-Through Procedure
Verifying true water level is the most vital watchkeeping duty for GP Ratings in the engine room. Blocked steam or water passages cause false water level indications, leading to disastrous dry boiler tube burnout. The statutory blow-through procedure is carried out as follows: GAUGE GLASS BLOW-THROUGH TESTING PROCEDURE
Step 1: Close water cock, open drain cock. Steam blows violently through.
(PROVES STEAM COCK & STEAM PASSAGE ARE CLEAR)
Step 2: Close steam cock, open water cock. Water blows violently through drain.
(PROVES WATER COCK & WATER PASSAGE ARE CLEAR)
Step 3: Close drain cock, open steam cock.
- (Water rushes rapidly back into glass and stabilizes at true level)
- 3. Boiler Feed Water Treatment & Chemistry Control
Water inside a marine boiler is subject to extreme temperatures and pressures that accelerate chemical reactions. Using raw seawater, shore tap water, or unconditioned distillate will rapidly destroy a marine boiler through three mechanisms:
Scale Formation : Dissolved calcium and magnesium salts precipitate onto hot furnace and tube surfaces, forming insulating rock-hard scale. A 1 mm 1\text{ mm} 1 mm layer of scale causes local tube overheating, blistering, and explosive rupture.
Corrosion and Oxygen Pitting : Dissolved oxygen ( O 2 O_2 O 2 ) and carbon dioxide ( C O 2 CO_2 C O 2 ) in feed water cause rapid localized pitting corrosion, drilling pinholes through steel tubes in weeks.
Caustic Embrittlement and Priming : Excessive alkalinity makes steel brittle along crystalline grain boundaries. High dissolved solids or oil contamination causes violent surface foaming, carrying liquid water over into steam lines (priming/carryover) and causing destructive hydraulic hammer in steam machinery.
Treatment Objective Conditioning Chemical Used Target Chemical Mechanism & Safe Limit
Alkalinity Control Sodium Hydroxide ( N a O H NaOH N a O H ) or Sodium Carbonate ( N a 2 C O 3 Na_2CO_3 N a 2 C O 3 ) Neutralizes acidic carbon dioxide; maintains boiler water pH between 9.5 9.5 9.5 and 11.0 11.0 11.0 . Passivates steel with a protective magnetite ( F e 3 O 4 Fe_3O_4 F e 3 O 4 ) layer.
Oxygen Scavenging Sodium Sulfite ( N a 2 S O 3 Na_2SO_3 N a 2 S O 3 ) or Hydrazine ( N 2 H 4 N_2H_4 N 2 H 4 ) Reacts chemically with dissolved oxygen: 2 N a 2 S O 3 + O 2 → 2 N a 2 S O 4 2Na_2SO_3 + O_2 \to 2Na_2SO_4 2 N a 2 S O 3 + O 2 → 2 N a 2 S O 4 . Eliminates oxygen pitting throughout tubes and economizers.
Hardness Precipitation Sodium Phosphate ( N a 3 P O 4 Na_3PO_4 N a 3 P O 4 ) Precipitates calcium as calcium phosphate. Adequate alkalinity controls magnesium, which forms hydroxide or silicate sludge. Conditioning keeps solids removable by blowdown instead of allowing deposits on heating surfaces.
Salinity / TDS Management Surface & Bottom Blowdown Blowdown discharges concentrated boiler water containing high Total Dissolved Solids (TDS) and replaces it with fresh feed distillate. Control chloride and TDS within the boiler maker and treatment programme limits.
Condensate Line Protection Neutralizing Amines Volatile chemicals that vaporize with steam and condense in piping to neutralize acidic C O 2 CO_2 C O 2 return lines.
Important
Daily Water Testing by Engine Watch : Engine ratings assist watch engineers in collecting daily boiler water samples from cooler sampling cocks. Testing tests for pH value, Phosphate reserve ( 20 – 40 ppm 20\text{--}40\text{ ppm} 20 – 40 ppm ), Sulfite reserve ( 30 – 50 ppm 30\text{--}50\text{ ppm} 30 – 50 ppm ), and Chloride content . Adjust doses to the approved test limits. Use the specified metering pump or bypass dosing pot; continuous dosing is preferred for suitable products, while a pot supplies measured batches. Avoid uncontrolled large additions.