Study guide

5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging

DG Shipping General Purpose Rating Final Exam India

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction to Shipping, Ship Structure & Organization

1.1 Maritime Trade, Ship Types & Principal Dimensions 1.2 Shipboard Organization, Ranks & Trainee GP Rating Duties 1.3 Hull Structure, Compartments & Watertight Openings 1.4 Computer Operation, Shipboard IT Systems & Digital Basics

2 Chapter 2: Navigation Basics, Bridge Equipment & Watchkeeping

2.1 Bridge Layout, Compass, Helmsman Duties & Steering Orders 2.2 Lookout Duties, Night Vision & STCW Bridge Watchkeeping 2.3 IALA Maritime Buoyage System (Region A) & Basic COLREGs Lights/Shapes

3 Chapter 3: Anchor Work, Mooring Operations & Tug Safety

3.1 Ground Tackle: Anchors, Cables, Windlass & Hawse Pipe 3.2 Mooring Equipment, Lines & Deck Fittings 3.3 Mooring & Unmooring Operations, Snap-Back Zones & Tug Safety

4 Chapter 4: Cargo Handling Gear, Stowage & Hold Maintenance

4.1 Cargo Handling Appliances: Derricks, Cranes & Safe Working Load (SWL) 4.2 Cargo Hold Preparation, Dunnage & Hold Cleaning 4.3 Container Cargo, Bulk Cargoes & IMDG Code Awareness

5 Chapter 5: Seamanship, Ropes, Rigging & Deck Maintenance

5.1 Natural, Synthetic & Wire Ropes: Care, Coiling & Splicing 5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging 5.3 Deck Maintenance: Chipping, Wire-Brushing, Painting & Working Aloft/Overside

6 Chapter 6: Shipboard Safety, Safe Working Practices & Permits

6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard 6.2 Permit to Work Systems & Enclosed Space Entry 6.3 Hot Work Precautions, Electrical Safety on Deck & Gangway Watch

7 Chapter 7: STCW Basic Safety, Firefighting & Life Saving Appliances

7.1 Life-Saving Appliances: Lifejackets, Immersion Suits & Lifebuoys 7.2 Survival Craft: Lifeboats, Liferafts & Launching Appliances 7.3 Basic Firefighting Principles, Fire Triangle & Portable Extinguishers 7.4 Elementary First Aid, CPR, Bleeding Control & Medical Emergency Response

8 Chapter 8: Marine Pollution Prevention & MARPOL Regulations

8.1 MARPOL Overview & Annex I: Oil Pollution Prevention 8.2 MARPOL Annex V: Garbage Management & Shipboard Waste 8.3 Bunkering Procedures, SOPEP & Spill Response

9 Chapter 9: Engine Room Familiarization, Watchkeeping & Safety

9.1 Engine Room Layout, Bilges, Tank Tops & Trainee Ratings Duties 9.2 Engine Room Instrumentation, Alarms & Emergency Escapes 9.3 Quick-Closing Valves, Emergency Stops & Fire Dampers

10 Chapter 10: Marine Diesel Engines: Cycles, Components & Systems

10.1 Two-Stroke & Four-Stroke Marine Diesel Operating Principles 10.2 Main Engine Structural Components & Moving Parts 10.3 Engine Support Systems: Fuel Oil, Lubricating Oil & Starting Air 10.4 Engine Cooling Water Systems & Scavenge Fires

11 Chapter 11: Marine Auxiliary Machinery, Heat Exchangers & Boilers

11.1 Air Compressors, Compressed Air Receivers & Centrifugal Purifiers 11.2 Fresh Water Generators (Evaporators) & Heat Exchangers 11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems 11.4 Domestic Services, Refrigeration, Air Conditioning & Sewage Treatment

12 Chapter 12: Marine Pumps, Piping Systems, Valves & Steering Gear

12.1 Centrifugal & Positive Displacement Marine Pumps 12.2 Valves, Filters, Strainers & Pipeline Identification 12.3 Bilge, Ballast & Oily Water Separator (OWS) Systems 12.4 Steering Gear Systems & Emergency Steering Procedures 12.5 Shipboard Plumbing Repairs, Pipe Clamping & Pipeline Maintenance

13 Chapter 13: Workshop Tools, Fitting, Hot Work & Electrical Safety

13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement 13.2 Power Tools, Grinding, Drilling & Safe Workshop Operations 13.3 Gas Welding, Electric Arc Welding & Hot Work Safety 13.4 Electrical Safety, Isolation, LOTO & Hazards in Machinery Spaces 13.5 Lathe Machine Operations, Centering & Fabrication 13.6 Shipboard Carpentry, Woodworking & Cement Box Emergency Repairs

14 Chapter 14: Engine Room Firefighting, Fixed Systems & Emergency Response

14.1 Machinery Space Fire Hazards & Flammable Liquids Management 14.2 Fixed Fire-Extinguishing Systems: CO2, Water Mist & Hi-Expansion Foam 14.3 Emergency Procedures: Blackout, Flooding, Abandon Ship & Engine Room Safety Drills

5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging

Key Takeaways Explain This Topic AI

Maritime seamanship classifies rope fastenings into knots (tied within a line), bends (joining two distinct lines), and hitches (fastening a line to a spar, ring, bollard, or another line under load).

The bowline ("king of knots") creates an unshakeable, non-slip temporary loop that will never jam under extreme strain, while the reef knot is strictly forbidden for lifting or safety lines because it capsizes easily.

A rolling hitch grips a rope or spar against axial pull. For mooring transfer, use a compatible stopper: natural fiber on natural fiber, suitable synthetic other than nylon on synthetic; COSWP prefers a double-tail West Country stopper.

Pulley tackles rigged to "advantage" have the hauling part leading from the moving block (pulling in the direction of load motion), giving a mechanical advantage equal to the parts supporting the load ( M A = n MA = n M A = n ), one higher than rigging to "disadvantage".

In practical shipboard rigging calculations, an empirical friction allowance of 10% of the load weight is added for every rotating sheave in the system: Effort ( P ) = W × ( 1 + 0.10 ⋅ n ) MA \text{Effort } (P) = \frac{W \times (1 + 0.10 \cdot n)}{\text{MA}} Effort ( P ) = MA W × ( 1 + 0.10 ⋅ n ) ​ .

Last updated: November 2026

Seamanship Knots, Bends, and Hitches

The ability to tie the correct knot swiftly and securely in darkness, driving rain, or heavy seas is the hallmark of an able seafarer. On board merchant vessels, ropes must be fastened reliably so they hold without slipping under massive dynamic surges, yet can be untied cleanly and rapidly without jamming once tension is eased.

Basic Cordage Terminology

Before examining individual knots, a GP Rating must master basic cordage terms:

Standing Part: The main, long, stationary part of the rope leading from the load or attachment point.

Working End (Bitter End): The free end of the line used to tie the knot, bend, or hitch.

Bight: A curved loop or bend formed in any part of a rope between its ends without crossing the parts.

Loop (Turn): Formed when the working part crosses over or under the standing part.

Round Turn: Passing the rope completely around a post, spar, or ring through a full 360° circle so both parts lead in parallel directions.

Knot Efficiency: Every knot or hitch forces rope fibers into tight radius curves, creating high stress concentrations. Standard knots reduce rope breaking strength by 40% to 55% . For example, a rope with a breaking strength of 10 tonnes will part at roughly 5 to 6 tonnes when tied with a bowline.

Fundamental Categories

Knots: Fastenings tied in a rope itself (e.g., stopper knots or decorative knobs).

Bends: Fastenings used to temporarily join two ropes together (either of equal or unequal diameter).

Hitches: Fastenings used to secure a rope to a solid spar, ring, bollard, stanchion, or another rope under tension.

  • 1. Essential Seamanship Knots & Hitches BOWLINE FIGURE-OF-EIGHT REEF KNOT
  • (Non-slip Eye) (Stopper Knot) (Binding Only)

.---. .---. .---.---.

  • / \ / | \ / / \ \
  • | O | | / \ | | | | |
  • \ | / \ | / \ \ / /
  • ==+=+=+== ===+=+=== '---'---'
  • Comprehensive Master Reference Table

Knot / Bend / Hitch Category Structural Description Primary Shipboard Application Critical Limitations & Safety Warnings

Figure-of-Eight Stopper Knot Crossed loop forming a distinct figure "8" profile Tied in the bitter end of halyards, boat falls, sheets, and gantlines Prevents line running out through a sheave or lead; does not jam and unties easily.

Reef Knot (Square Knot) Binding Knot Two opposing overhand knots formed with ends emerging parallel Tying reef points on canvas, sail covers, hatch tarpaulin lashings NEVER join two lines under load or safety lines! Capsizes into a lethal slip knot under unequal tension.

Bowline Eye Knot Non-slip temporary eye formed by an overhand loop and round turn Mooring hawser eyes, rescue lines, gantlines, securing heaving lines "King of Knots." Will not slip, tighten, or jam under immense load; readily untied after strain is released.

Running Bowline Running Eye / Noose Bowline tied around its own standing part Retrieving floating spars, retrieving overboard cargo, retrieving boat painter Forms a running noose that cinches tightly around distant or floating objects under load.

Bowline on a Bight Double Eye Knot Tied in the bight of a line without access to the ends Hoisting an unconscious or injured crew member; emergency bosun's seat Creates two secure, non-collapsing loops: one loop fits under thighs, the second around the chest.

Clove Hitch Hitch Two opposing half hitches around a cylinder Securing ratlines to rigging shrouds; temporary mooring of small workboats Holds reliably only under constant, two-way perpendicular strain; slips if strain is slackened or pulled along the spar.

Timber Hitch & Killick Towing / Lifting Hitch Half turn with 3 or more dogging wraps tucked back against the lay Towing, hoisting, or dragging cylindrical wooden spars, planks, and timber Must be kept under continuous tension; Killick hitch adds an extra half-hitch forward to lead the spar straight.

Rolling Hitch Friction Hitch Two round turns toward the direction of strain plus one half-hitch Basic rope-stopper hitch; securing a line to a spar under axial tension. Mooring transfer requires a compatible stopper and approved method Specifically engineered NOT to slip in the direction of pull along another rope or cylindrical spar.

Single Sheet Bend Bend Working end passed through a bight and under its own standing part Joining two dry ropes of slightly unequal diameters Working ends must finish on the same side of the bend; slips if ropes are wet, slick, or synthetic.

Double Sheet Bend Bend Two round turns around the bight before tucking working end Joining ropes of significantly unequal thickness, or synthetic lines Extra round turn provides gripping friction, preventing thin or synthetic lines from spilling out.

Round Turn & Two Half Hitches Hitch Full 360° turn around ring/spar followed by two half hitches Securing boat painters, heavy mooring hawsers, and fenders to ringbolts Exceptional holding power. Will not jam under immense strain and can be cast off safely even while line is under tension!

Sheepshank Shortening Knot Two opposing half hitches thrown over folded bights Temporarily shortening a long line without cutting; taking strain off a chafed section Unstable! Holds only while maintained under continuous, uninterrupted tension; spills instantly when slackened.

Fisherman's Bend (Anchor Bend) Hitch Two round turns through ring, with first half-hitch passed inside turns Securing rope cable to an anchor ring, mooring buoy, or heavy shackle Highly resistant to cyclic chafing, wave motion, and surging; can be seized to standing part for permanent security.

Operational Deep Dive: The Rolling Hitch & Rope Stopper

Transferring a mooring hawser from a warping drum to bitts requires a suitable stopper and a coordinated team. A rolling hitch illustrates axial grip, but it is not the mandatory method for every mooring rope. COSWP prefers the double-tail West Country stopper for fiber moorings.

Select a stopper suitable for the line and load. Use natural fiber on natural-fiber moorings, and a compatible synthetic stopper on synthetic moorings; do not use polyamide (nylon) as the synthetic stopper . Check its condition and secure attachment.

Apply the stopper by the ship's approved method. With a double-tail West Country stopper, alternate the two tails around the hawser in the prescribed opposing pattern. The responsible supervisor checks the rig before load transfer.

Keep everyone clear of bights and recoil paths. Agree clear signals with the winch operator; ease the drum only when the stopper is ready to take the strain.

Transfer the line onto the bitts using the approved lead and securing pattern; single turns or figures of eight may be used. Keep hands clear of trapping points.

Ease and remove the stopper only after the line is secure on the bitts and the supervisor confirms the transfer is complete.

Caution

A stopper is temporary. Incorrect material, poor rigging or uncontrolled load transfer can release the hawser. Stop and report any slipping or damage; never try to catch a running line by hand.

2. Anatomy and Types of Pulley Blocks

A pulley block (or maritime block) is a portable or fixed mechanical device housing one or more grooved wheels (sheaves). Blocks change the lead of a line, minimize frictional wear, and compound lifting force into mechanical advantage. ANATOMY OF A PULLEY BLOCK

  • [Head Fitting] (Eye / Hook / Shackle)
  • |
  • +----+----+
  • | [Cheek] |
  • [Swallow] (SHEAVE) [Swallow]
  • | | |
  • | [Pin] |
  • +----+----+
  • |
  • [Becket] (Bottom Eye)
  • Components of a Block

Shell: The outer frame or housing that encases the sheaves. Manufactured from cast steel, drop-forged alloy, galvanized mild steel, or seasoned hardwood (elm or ash).

Sheave: The grooved wheel over which the rope or wire passes. Fabricated from cast iron, phosphor bronze, or cast steel. The sheave groove must match the rope diameter: if the groove is too narrow, it pinches and crushes the rope; if too wide, the rope flattens under load.

Pin (Axle): The central hardened steel bolt passing through the cheeks and sheave hub. Equipped with an internal grease duct or Zerk grease nipple for lubrication.

Cheek: The solid side plates of the shell enclosing the sheave.

Strap: A continuous internal or external forged steel band that binds the shell, carrying tensile load between the head fitting, pin, and becket.

Swallow: The open throat between the cheeks above the sheave where the rope enters and exits.

Becket: A small forged eye, thimble, or lug at the base of the block used to anchor the standing part of the rope.

Block Classifications

By Number of Sheaves:

Single Sheave Block: Houses 1 sheave.

Double Sheave Block: Houses 2 sheaves rotating independently on a common central pin.

Treble Sheave Block: Houses 3 sheaves rotating independently on a common central pin.

The Snatch Block:

A heavy-duty single-sheave block featuring a hinged cheek or gate that swings open on one side.

Seamanship Advantage : Allows the bight of a rope or wire to be inserted directly into the sheave without threading the bitter end through the swallow. Once the bight is seated, the hinged cheek is closed and locked with a spring-loaded toggle or safety pin.

Widely used on deck for altering the lead of mooring lines, warping wires, and cargo runners.

3. Mechanical Advantage and Tackle Purchases

A tackle (pronounced "tay-kle" in maritime parlance) is an assembly of ropes (falls) reeved through one or more blocks to gain mechanical advantage (MA) , multiplying the hauling effort of the crew or winch.

Tackle Terminology

Falls: The entire rope reeved through the blocks of a tackle.

Standing Part: The end of the falls permanently secured to the becket of a block.

Hauling Part: The free end of the falls upon which the crew or winch pulls.

Running Parts: The moving intermediate lengths of rope passing between the sheaves.

Fixed Block: The block anchored to a static overhead structure (deckhead, derrick head, or mast).

Moving Block: The block attached directly to the load, moving with it.

Rigged to Advantage versus Rigged to Disadvantage

A purchase can be rigged in two opposite configurations, altering its pulling power: RIGGED TO DISADVANTAGE RIGGED TO ADVANTAGE

  • Hauling Part from Fixed Block Hauling Part from Moving Block
  • [FIXED BLOCK] [FIXED BLOCK]
  • / | \ | \
  • (Haul) | \ | \
  • v | \ | \
  • | \ | \
  • [MOVING BLOCK] [MOVING BLOCK]
  • | / |
  • [LOAD] (Haul) |
  • ^ [LOAD]

Effort pulls opposite to load. Effort pulls in direction of load.

MA = All supporting parts. MA = All supporting parts,

INCLUDING the hauling part once.

Inverting the SAME tackle adds one supporting part; do not count it twice.

Rigged to Disadvantage:

The hauling part leads away from the fixed block .

The crew pulls in the opposite direction to the load movement (e.g., pulling downward to raise a load upward).

Theoretical MA \text{MA} MA equals the number of parts of rope supporting the moving block: MA disadvantage = parts supporting load \text{MA}_{\text{disadvantage}} = \text{parts supporting load} MA disadvantage ​ = parts supporting load

Rigged to Advantage:

The hauling part leads away from the moving block .

The crew pulls in the same direction as the load moves (e.g., pulling upward to raise a load upward).

Because the hauling part itself directly helps support the load, the theoretical mechanical advantage increases by 1: MA advantage = MA disadvantage + 1 = total parts supporting/moving load \text{MA}_{\text{advantage}} = \text{MA}_{\text{disadvantage}} + 1 = \text{total parts supporting/moving load} MA advantage ​ = MA disadvantage ​ + 1 = total parts supporting/moving load

Master Tackle Reference Table

Tackle Purchase Blocks Used Total Sheaves ( n n n ) Theoretical MA (Disadvantage) Theoretical MA (Advantage) Primary Shipboard Application

Single Whip 1 Single (Fixed) 1 1 (No advantage) N/A Changing direction of pull; hoisting light paint pots or tools

  • Runner 1 Single (Moving) 1 N/A 2 Cargo crane hoist whip, mooring fairlead lead
  • Gun Tackle 2 Single Blocks 2 2 3 Gangway hoisting, light boat purchase, awning halyards
  • Luff Tackle 1 Double + 1 Single 3 3 4 General heavy deck lifting, life raft davits, mooring stoppers
  • Two-Fold Purchase 2 Double Blocks 4 4 5 Accommodation ladder purchases, lifeboat falls, cargo gear
  • Three-Fold Purchase 2 Treble Blocks 6 6 7 Heavy lift derricks (up to 50+ MT), heavy spar hoisting
  • 4. Tackle Friction Calculations: The 10% Seamanship Rule

In real-world seamanship, theoretical mechanical advantage overestimates lifting capacity because friction in sheave bearings and bending resistance of the rope consume significant energy.

The Standard Seamanship Friction Formula

The international maritime standard rule of thumb accounts for friction by adding 10% (one-tenth) of the original load weight for every rotating sheave in the purchase:

Friction Allowance = n × 0.10 × W \text{Friction Allowance} = n \times 0.10 \times W Friction Allowance = n × 0.10 × W

where:

W W W = weight of the load to be hoisted.

n n n = total number of rotating sheaves in the entire tackle system.

The Total Effective Load ( W eff W_{\text{eff}} W eff ​ ) including friction is:

W eff = W + ( n × 0.10 × W ) = W × ( 1 + 0.10 ⋅ n ) W_{\text{eff}} = W + (n \times 0.10 \times W) = W \times (1 + 0.10 \cdot n) W eff ​ = W + ( n × 0.10 × W ) = W × ( 1 + 0.10 ⋅ n )

The Hauling Effort ( P P P ) required on the hauling part is:

P = W eff MA = W × ( 1 + 0.10 ⋅ n ) MA P = \frac{W_{\text{eff}}}{\text{MA}} = \frac{W \times (1 + 0.10 \cdot n)}{\text{MA}} P = MA W eff ​ ​ = MA W × ( 1 + 0.10 ⋅ n ) ​

where MA \text{MA} MA is the theoretical mechanical advantage (determined by whether the tackle is rigged to advantage or disadvantage).

Worked Calculation Example

Problem: A deck maintenance crew must lift a spare lubricating oil pump casing weighing 800 kg through an engine room skylight. They rig a Two-Fold Purchase (consisting of two double blocks, totaling n = 4 n = 4 n = 4 sheaves). The purchase is rigged to advantage (hauling part leads from the moving block, so MA = 5 \text{MA} = 5 MA = 5 ). Calculate the required pulling force on the hauling part.

Step 1: Calculate the friction allowance Friction = 4 × 0.10 × 800 kg = 0.40 × 800 kg = 320 kg \text{Friction} = 4 \times 0.10 \times 800\text{ kg} = 0.40 \times 800\text{ kg} = 320\text{ kg} Friction = 4 × 0.10 × 800 kg = 0.40 × 800 kg = 320 kg

Step 2: Calculate total effective load ( W eff W_{\text{eff}} W eff ​ ) W eff = 800 kg + 320 kg = 1 , 120 kg W_{\text{eff}} = 800\text{ kg} + 320\text{ kg} = 1,120\text{ kg} W eff ​ = 800 kg + 320 kg = 1 , 120 kg

Step 3: Calculate required effort ( P P P ) P = W eff MA = 1 , 120 kg 5 = 224 kg P = \frac{W_{\text{eff}}}{\text{MA}} = \frac{1,120\text{ kg}}{5} = 224\text{ kg} P = MA W eff ​ ​ = 5 1 , 120 kg ​ = 224 kg

Analysis : In a frictionless theoretical system, the required effort would be 800 / 5 = 160 kg 800 / 5 = 160\text{ kg} 800/5 = 160 kg . Sheave friction adds 64 kg 64\text{ kg} 64 kg of resistance, requiring an actual hauling force of 224 kg 224\text{ kg} 224 kg .