Study guide

6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard

DG Shipping General Purpose Rating Final Exam India

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction to Shipping, Ship Structure & Organization

1.1 Maritime Trade, Ship Types & Principal Dimensions 1.2 Shipboard Organization, Ranks & Trainee GP Rating Duties 1.3 Hull Structure, Compartments & Watertight Openings 1.4 Computer Operation, Shipboard IT Systems & Digital Basics

2 Chapter 2: Navigation Basics, Bridge Equipment & Watchkeeping

2.1 Bridge Layout, Compass, Helmsman Duties & Steering Orders 2.2 Lookout Duties, Night Vision & STCW Bridge Watchkeeping 2.3 IALA Maritime Buoyage System (Region A) & Basic COLREGs Lights/Shapes

3 Chapter 3: Anchor Work, Mooring Operations & Tug Safety

3.1 Ground Tackle: Anchors, Cables, Windlass & Hawse Pipe 3.2 Mooring Equipment, Lines & Deck Fittings 3.3 Mooring & Unmooring Operations, Snap-Back Zones & Tug Safety

4 Chapter 4: Cargo Handling Gear, Stowage & Hold Maintenance

4.1 Cargo Handling Appliances: Derricks, Cranes & Safe Working Load (SWL) 4.2 Cargo Hold Preparation, Dunnage & Hold Cleaning 4.3 Container Cargo, Bulk Cargoes & IMDG Code Awareness

5 Chapter 5: Seamanship, Ropes, Rigging & Deck Maintenance

5.1 Natural, Synthetic & Wire Ropes: Care, Coiling & Splicing 5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging 5.3 Deck Maintenance: Chipping, Wire-Brushing, Painting & Working Aloft/Overside

6 Chapter 6: Shipboard Safety, Safe Working Practices & Permits

6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard 6.2 Permit to Work Systems & Enclosed Space Entry 6.3 Hot Work Precautions, Electrical Safety on Deck & Gangway Watch

7 Chapter 7: STCW Basic Safety, Firefighting & Life Saving Appliances

7.1 Life-Saving Appliances: Lifejackets, Immersion Suits & Lifebuoys 7.2 Survival Craft: Lifeboats, Liferafts & Launching Appliances 7.3 Basic Firefighting Principles, Fire Triangle & Portable Extinguishers 7.4 Elementary First Aid, CPR, Bleeding Control & Medical Emergency Response

8 Chapter 8: Marine Pollution Prevention & MARPOL Regulations

8.1 MARPOL Overview & Annex I: Oil Pollution Prevention 8.2 MARPOL Annex V: Garbage Management & Shipboard Waste 8.3 Bunkering Procedures, SOPEP & Spill Response

9 Chapter 9: Engine Room Familiarization, Watchkeeping & Safety

9.1 Engine Room Layout, Bilges, Tank Tops & Trainee Ratings Duties 9.2 Engine Room Instrumentation, Alarms & Emergency Escapes 9.3 Quick-Closing Valves, Emergency Stops & Fire Dampers

10 Chapter 10: Marine Diesel Engines: Cycles, Components & Systems

10.1 Two-Stroke & Four-Stroke Marine Diesel Operating Principles 10.2 Main Engine Structural Components & Moving Parts 10.3 Engine Support Systems: Fuel Oil, Lubricating Oil & Starting Air 10.4 Engine Cooling Water Systems & Scavenge Fires

11 Chapter 11: Marine Auxiliary Machinery, Heat Exchangers & Boilers

11.1 Air Compressors, Compressed Air Receivers & Centrifugal Purifiers 11.2 Fresh Water Generators (Evaporators) & Heat Exchangers 11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems 11.4 Domestic Services, Refrigeration, Air Conditioning & Sewage Treatment

12 Chapter 12: Marine Pumps, Piping Systems, Valves & Steering Gear

12.1 Centrifugal & Positive Displacement Marine Pumps 12.2 Valves, Filters, Strainers & Pipeline Identification 12.3 Bilge, Ballast & Oily Water Separator (OWS) Systems 12.4 Steering Gear Systems & Emergency Steering Procedures 12.5 Shipboard Plumbing Repairs, Pipe Clamping & Pipeline Maintenance

13 Chapter 13: Workshop Tools, Fitting, Hot Work & Electrical Safety

13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement 13.2 Power Tools, Grinding, Drilling & Safe Workshop Operations 13.3 Gas Welding, Electric Arc Welding & Hot Work Safety 13.4 Electrical Safety, Isolation, LOTO & Hazards in Machinery Spaces 13.5 Lathe Machine Operations, Centering & Fabrication 13.6 Shipboard Carpentry, Woodworking & Cement Box Emergency Repairs

14 Chapter 14: Engine Room Firefighting, Fixed Systems & Emergency Response

14.1 Machinery Space Fire Hazards & Flammable Liquids Management 14.2 Fixed Fire-Extinguishing Systems: CO2, Water Mist & Hi-Expansion Foam 14.3 Emergency Procedures: Blackout, Flooding, Abandon Ship & Engine Room Safety Drills

6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard

Key Takeaways Explain This Topic AI

India’s Maritime Labour Rules, 2026, and MLC Standard A4.3 provide the occupational-safety framework. COSWP supplies practical UK guidance; a ship with five or more seafarers needs a safety committee with seafarer representation.

Personal Protective Equipment (PPE) is the final line of defense in the hierarchy of hazard controls, requiring certified gear such as 200-Joule impact-resistant safety footwear, optical welding filters (shades 10–12 for arc, 4–6 for gas), and fall-arrest harnesses.

Hearing protection (ear plugs or earmuffs with NRR 25–30 dB) is strictly mandatory in any shipboard area with continuous noise exceeding 85 dB(A), with dual protection advised above 100 dB(A).

Every seafarer, including a trainee rating, should stop unsafe work, warn others and report the hazard under the ship’s SMS. Resume only after the supervisor reassesses the risk and confirms effective controls.

Assess the load, person, task and ship’s motion before lifting. Bend the knees and hips, preserve the back’s natural curve, keep the load close and lift smoothly with the legs; use help or mechanical aids when needed.

Last updated: November 2026

6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard

Merchant shipping operates within an inherently hazardous environment where heavy steel machinery, extreme marine weather, high-voltage electrical circuits, and hazardous chemical cargoes create constant operational risks. The Directorate General of Shipping (DG Shipping), Ministry of Ports, Shipping and Waterways, Government of India, places paramount importance on occupational safety training for General Purpose (GP) Ratings. Trainee seafarers must thoroughly master the Code of Safe Working Practices for Merchant Seafarers (COSWP), the technical specifications and maintenance of Personal Protective Equipment (PPE), structured risk assessment procedures, the conduction of Toolbox Talks (TBT), and ergonomic manual handling techniques.

1. Code of Safe Working Practices for Merchant Seafarers (COSWP)

The Code of Safe Working Practices for Merchant Seafarers (COSWP) is published by the UK Maritime and Coastguard Agency (MCA), primarily for UK-registered merchant ships. It explains UK duties and practical safe working methods. For applicable Indian ships, rule 20 of the Merchant Shipping (Maritime Labour) Rules, 2026 , implements occupational health and safety protection in accordance with MLC Standard A4.3 . Apply the ship’s flag-state requirements and Safety Management System (SMS).

Legal Status and Accessibility

Onboard Access : UK rules require carriage of COSWP on applicable UK ships and ready access for seafarers. On other flags, follow the administration’s requirements and keep the ship’s safety instructions accessible.

Duty of Compliance : Shipowners must provide safe working arrangements; seafarers must follow safety instructions and use safeguards correctly. Report hazards and defective equipment through the SMS.

The Shipboard Safety Committee

Under MLC Standard A4.3 , ships with five or more seafarers must have a Shipboard Safety Committee . Seafarer safety representatives participate in its work. The following is a typical arrangement, with the Master as chairman as described in COSWP: +------------------------------+

  • | MASTER (CHAIRMAN) |
  • | - Ultimate safety authority |
  • +--------------+---------------+
  • |
  • +--------------------------+--------------------------+
  • | |
  • +-------+----------------------+ +-----------------+-----------------------+
  • | SAFETY OFFICER | | ELECTED SAFETY REPRESENTATIVES |
  • | (Chief Officer / 2nd Engr) | | - Deck Rating Representative |
  • | - Daily safety inspections | | - Engine Rating Representative |
  • | - Accident investigations | | - Catering Rating Representative |
  • | - Risk assessments & permits | | - Direct voice for crew safety concerns |
  • +------------------------------+ +-----------------------------------------+

The Master (Chairman) :

Holds overall statutory command and ultimate responsibility for health, safety, and environmental protection onboard.

Reviews and endorses safety committee recommendations, allocating vessel resources for hazard rectification.

The Safety Officer :

Appointed under the applicable flag-state rules and company procedures. COSWP places appointment with the company ; an appropriately trained officer, such as the Chief Officer, may perform the role, with assistance from other departments.

Key Duties : Conducts daily safety inspections of working areas; investigates accidents, injuries, and near-miss occurrences; maintains statutory safety records; verifies Permit to Work (PTW) documentation; promotes occupational safety awareness among junior ratings.

Safety Representatives :

Chosen to represent seafarers under the flag-state arrangements; departmental representation helps include deck, engine and catering concerns.

Under UK rules described in COSWP, representatives need two years’ consecutive sea service after age 18; a tanker representative also needs at least six months on tankers.

Key Duties : Represent ratings' views at committee meetings; inspect work locations following safety complaints; accompany the Safety Officer during hazard inspections; encourage fellow ratings to adopt safe working practices without fear of management reprisal.

Safety Committee Meetings :

Convened at regular intervals, typically once every month , or immediately following a serious accident, high-potential near-miss, or major operational change.

Record decisions, corrective actions and follow-up in the minutes. Make them available to the crew and relevant shore managers according to the company’s SMS.

2. Personal Protective Equipment (PPE): Standards, Inspection & Maintenance

Personal Protective Equipment (PPE) comprises specialized garments and equipment designed to shield seafarers from physical, chemical, electrical, or biological hazards. It is vital to remember that PPE does not eliminate the hazard ; it serves solely as the final barrier between the worker and injury.

PPE Category Equipment Type Technical Standard / Specification Key Inspection & Shipboard Maintenance Criteria

Head Protection Industrial Safety Helmet (Hard Hat) EN 397 / IS 2925; rigid HDPE or polycarbonate shell with internal 6-point cradle harness Inspect shell for cracks, chips, and UV chalking; ensure internal harness webbing is intact; mandatory adjustable chin strap when working aloft, overside, or on windy open decks; discard after heavy impact or 3–5 years service life

Eye & Face Protection Safety Glasses, Impact Goggles, Face Shield EN 166; polycarbonate scratch-resistant lenses with side shields; indirect-vent chemical splash goggles Discard scratched or pitted lenses that impair vision; clean with fresh water and microfiber cloth; use full face shield during grinding, needle gunning, and handling corrosive battery acid

Hot Work Optical Filters Welding Helmets & Gas-Cutting Goggles EN 169 / EN 175; mineral glass filter lenses with designated shade numbers Shade 10–12 for Shielded Metal Arc Welding (SMAW/stick) and MIG welding; Shade 4–6 for oxy-acetylene flame cutting and brazing; never strike an arc with bare eyes (causes photokeratitis / 'arc eye')

Hearing Protection Expandable Foam Ear Plugs & Ear Defenders (Muffs) EN 352 / IS 9167; Noise Reduction Rating (NRR) of 25–30 dB Mandatory in all areas exceeding 85 dB(A) 85\text{ dB(A)} 85 dB(A) (engine room, purifier room, compressor flat, paint chipping); dual protection (plugs + muffs) recommended near running diesel generators ( > 100 dB(A) > 100\text{ dB(A)} > 100 dB(A) )

Hand Protection Leather Riggers, Chemical Gauntlets, Welding Gloves EN 388 (mechanical), EN 374 (chemical), EN 407 (thermal), EN 60903 (dielectric) Chrome leather riggers for wire ropes, cargo lashing, and anchor gear; nitrile/PVC gauntlets for fuels, oils, solvents, and bilge acids; split-cowhide gauntlets for hot work; rubber dielectric gloves selected for voltage: Class 00 up to 500 V AC; Class 0 up to 1,000 V AC; inspect for damage and pinholes

Foot Protection Safety Boots / Shoes EN ISO 20345 / IS 15298; Class S3 with steel or composite toe-cap Steel toe-cap must withstand 200 Joules impact and 15 kN crushing force; oil-resistant, acid-resistant, non-slip cleated polyurethane soles; stainless steel puncture-resistant midsoles; inspect soles for worn tread or embedded steel turnings

Body Protection High-Visibility Cotton Boiler Suit (Coverall) 100% heavy cotton or flame-retardant fabric; retro-reflective tape on shoulders, arms, and legs Snug fit; sleeves buttoned at wrists; loose belts or flapping cloth strictly prohibited around rotating shafts, lathes, and winches; wash regularly to prevent oil-soaked fabric from catching fire

Respiratory Protection Dust Masks, Cartridge Respirators, SCBA EN 149 (particulate), EN 14387 (chemical cartridges), EN 137 (SCBA) Select particulate filters for the assessed dust and suitable vapour cartridges within their use limits; ensure correct face fit. Use appropriate breathing apparatus for firefighting or authorized entry into unsafe atmospheres; filtering masks do not supply oxygen

Fall Protection Full-Body Safety Harness & Energy-Absorbing Lanyard EN 361 / IS 3521; dorsal/sternal D-rings, rip-stitch energy absorber, inertia reel lifeline Single waist belts are strictly prohibited for fall arrest; inspect stitching, webbing cuts, and D-ring corrosion before every use; snap hooks must be double-action self-locking; anchor only to certified structural pad eyes

Warning

Single waist belts (body belts) must never be used as fall-arrest equipment! In a fall, a body belt concentrates arresting forces across the seafarer's abdomen and lumbar spine, causing fatal internal hemorrhaging or asphyxiation. Only certified full-body safety harnesses with energy-absorbing lanyards or inertia reels are permitted for working aloft or overside.

3. Risk Assessment and The Toolbox Talk (TBT)

Every operational task performed on a merchant vessel—whether routine paint chipping, mooring line handling, or overhauling a purifier—carries inherent hazards. Modern maritime safety culture relies on proactive risk assessment to identify hazards before work commences.

The Hierarchy of Hazard Controls

When evaluating risks, the shipboard team must apply controls in a strict descending hierarchy. Controls at the top of the pyramid are fundamentally more reliable than those at the bottom. +-------------------------------------------------------------+

  • | 1. ELIMINATION (Physically remove the hazard) | Most Effective
  • +-------------------------------------------------------------+
  • | 2. SUBSTITUTION (Replace hazard with safer alternative)| ^
  • +-------------------------------------------------------------+ |
  • | 3. ENGINEERING (Isolate people from the hazard) | |
  • +-------------------------------------------------------------+ |
  • | 4. ADMINISTRATIVE (Change the way people work) | |
  • +-------------------------------------------------------------+ v
  • | 5. PPE (Protect worker with personal gear) | Least Effective
  • +-------------------------------------------------------------+

Elimination : Completely remove the hazard from the workplace. For example, instead of sending a rating overside on a stage to paint the vessel's flare at sea, the job is deferred to drydock where shore scaffolding is erected.

Substitution : Replace a hazardous material or tool with a less hazardous one. For example, substituting toxic, highly volatile solvent-based paint strippers with biodegradable, water-based degreasing agents.

Engineering Controls : Implement physical engineering measures that isolate crew members from the danger. Examples include installing fixed protective machinery guards around rotating winch drums and lathe chucks, fitting acoustic enclosures over diesel generators, or installing mechanical explosion-proof extraction fans in paint lockers.

Administrative Controls : Establish procedures, policies, and training to regulate work practices. Examples include issuing Permits to Work (PTW), implementing Lockout/Tagout (LOTO) protocols, scheduling mandatory rest periods under STCW to combat fatigue, and posting warning signs.

Personal Protective Equipment (PPE) : The final line of defense. Used only when hazards cannot be engineered out completely. Relies entirely on individual human compliance and equipment condition.

Conducting a Toolbox Talk (TBT)

A Toolbox Talk (TBT) is an informal yet structured safety briefing conducted at the physical job site immediately prior to commencing any work. It bridges the gap between written safety procedures and real-time execution.

Leadership : Led by the job supervisor (e.g., Bosun on deck, Fitter or Second Engineer in the workshop).

Attendees : All crew members assigned to the work party, including trainee GP ratings.

Core Elements Covered :

Task Brief : Clear explanation of what needs to be done, sequence of steps, and expected completion time.

Hazard Identification : Specific hazards associated with the job (e.g., ship roll, wet decks, pressurized lines, overhead crane movements, toxic fumes).

Individual Role Allocation : Assigning precise duties to each crew member according to skill level.

PPE and Tool Verification : Confirming that correct tools (e.g., insulated hand tools, non-sparking brass hammers) and PPE are staged, inspected, and properly worn.

Emergency Procedures & Stop Signals : Establishing clear verbal commands or hand signals to pause or abort the operation in an emergency.

Stop-Work Authority (SWA)

Important

Stop-Work Authority (SWA) is implemented through the company’s safety policy and SMS. Every crew member, including a trainee GP rating, should stop unsafe work, warn those exposed and notify the supervisor. Examples include a missing guard, damaged equipment, uncontrolled load or sudden deterioration in sea conditions. The supervisor must reassess the task, establish effective controls and brief the team before authorizing work to resume.

4. Safe Manual Handling & Kinetic Lifting Principles

Unsafe manual handling can cause musculoskeletal injuries, including back sprains and disc injuries, among deck and engine ratings. Moving heavy machinery spares, grease drums, paint cans, and mooring lines aboard a rolling, pitching vessel requires strict adherence to kinetic lifting techniques .

The Kinetic Lifting Technique (Step-by-Step) 1. FEET POSITION 2. SQUAT POSTURE 3. SMOOTH DRIVE

  • [ O ] [ O ] [ O ]
  • | | | Load held
  • /----+----\ /----+----\ /----+----\ close
  • / | \ / | \ / [===] \ to chest
  • / \ / \ / \
  • / \ / \ / \ Drive with
  • _/ \_ _/__ __\_ _/ \_ leg muscles
  • Feet shoulder-width apart, Knees bent, back straight, Push up with powerful
  • one foot slightly forward firm palm grip on load quadriceps, do NOT twist

Stop and Assess :

Check the load's weight, dimensions, and center of gravity.

Inspect for sharp edges, slippery grease, protruding wire snags, or hot surfaces.

Verify that the path of travel is completely free of trip hazards, lashing eyes, oil slicks, and open deck manholes.

Adopt a Stable Base :

Stand with feet hip- to shoulder-width apart.

Place one foot slightly forward beside the load to maintain balance against ship rolling motions.

Bend the Knees, Not the Back :

Lower the body by bending the knees and hips into a squat.

Maintain the spine's natural straight posture (head held upright, chin tucked, chest thrust forward).

Avoid bending forward with locked knees ; holding a load away from the body increases its lever arm and the load on the lower back.

Secure a Full Palm Grip :

Grasp the load using the entire palm and roots of the fingers, not just the fingertips.

Use gloves with non-slip grips.

Lift Smoothly with Leg Muscles :

Keep the load close to the body throughout the lift, with its heavier side nearest the trunk.

Straighten the legs smoothly, driving upward with the powerful quadriceps and gluteal muscles.

Avoid jerky, abrupt upward thrusts.

Never Twist While Carrying :

Never twist the waist or torso while holding or lifting a heavy object.

To change direction, pause and turn the entire body by moving the feet.

Safe Weight Limits Onboard

Assess Each Lift : There is no single weight that is safe for every seafarer or task. Consider the load’s weight and grip, lifting height, reach, frequency, route, individual capability and deck conditions. Weight guidelines are screening aids, not guaranteed safe limits.

Vessel Motion : Rolling and pitching impair balance and can increase handling forces. Reassess the operation; postpone it if necessary. Use suitable mechanical aids or a planned team lift , with enough people of similar height lifting together on one person’s command. Do not assume that halving a nominal limit makes heavy-weather lifting safe.