Study guide
13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement
DG Shipping General Purpose Rating Final Exam India
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction to Shipping, Ship Structure & Organization
1.1 Maritime Trade, Ship Types & Principal Dimensions 1.2 Shipboard Organization, Ranks & Trainee GP Rating Duties 1.3 Hull Structure, Compartments & Watertight Openings 1.4 Computer Operation, Shipboard IT Systems & Digital Basics
2 Chapter 2: Navigation Basics, Bridge Equipment & Watchkeeping
2.1 Bridge Layout, Compass, Helmsman Duties & Steering Orders 2.2 Lookout Duties, Night Vision & STCW Bridge Watchkeeping 2.3 IALA Maritime Buoyage System (Region A) & Basic COLREGs Lights/Shapes
3 Chapter 3: Anchor Work, Mooring Operations & Tug Safety
3.1 Ground Tackle: Anchors, Cables, Windlass & Hawse Pipe 3.2 Mooring Equipment, Lines & Deck Fittings 3.3 Mooring & Unmooring Operations, Snap-Back Zones & Tug Safety
4 Chapter 4: Cargo Handling Gear, Stowage & Hold Maintenance
4.1 Cargo Handling Appliances: Derricks, Cranes & Safe Working Load (SWL) 4.2 Cargo Hold Preparation, Dunnage & Hold Cleaning 4.3 Container Cargo, Bulk Cargoes & IMDG Code Awareness
5 Chapter 5: Seamanship, Ropes, Rigging & Deck Maintenance
5.1 Natural, Synthetic & Wire Ropes: Care, Coiling & Splicing 5.2 Seamanship Knots, Bends, Hitches & Block/Tackle Rigging 5.3 Deck Maintenance: Chipping, Wire-Brushing, Painting & Working Aloft/Overside
6 Chapter 6: Shipboard Safety, Safe Working Practices & Permits
6.1 Personal Protective Equipment (PPE) & Risk Assessment Onboard 6.2 Permit to Work Systems & Enclosed Space Entry 6.3 Hot Work Precautions, Electrical Safety on Deck & Gangway Watch
7 Chapter 7: STCW Basic Safety, Firefighting & Life Saving Appliances
7.1 Life-Saving Appliances: Lifejackets, Immersion Suits & Lifebuoys 7.2 Survival Craft: Lifeboats, Liferafts & Launching Appliances 7.3 Basic Firefighting Principles, Fire Triangle & Portable Extinguishers 7.4 Elementary First Aid, CPR, Bleeding Control & Medical Emergency Response
8 Chapter 8: Marine Pollution Prevention & MARPOL Regulations
8.1 MARPOL Overview & Annex I: Oil Pollution Prevention 8.2 MARPOL Annex V: Garbage Management & Shipboard Waste 8.3 Bunkering Procedures, SOPEP & Spill Response
9 Chapter 9: Engine Room Familiarization, Watchkeeping & Safety
9.1 Engine Room Layout, Bilges, Tank Tops & Trainee Ratings Duties 9.2 Engine Room Instrumentation, Alarms & Emergency Escapes 9.3 Quick-Closing Valves, Emergency Stops & Fire Dampers
10 Chapter 10: Marine Diesel Engines: Cycles, Components & Systems
10.1 Two-Stroke & Four-Stroke Marine Diesel Operating Principles 10.2 Main Engine Structural Components & Moving Parts 10.3 Engine Support Systems: Fuel Oil, Lubricating Oil & Starting Air 10.4 Engine Cooling Water Systems & Scavenge Fires
11 Chapter 11: Marine Auxiliary Machinery, Heat Exchangers & Boilers
11.1 Air Compressors, Compressed Air Receivers & Centrifugal Purifiers 11.2 Fresh Water Generators (Evaporators) & Heat Exchangers 11.3 Marine Boilers, Exhaust Gas Economizers & Steam Systems 11.4 Domestic Services, Refrigeration, Air Conditioning & Sewage Treatment
12 Chapter 12: Marine Pumps, Piping Systems, Valves & Steering Gear
12.1 Centrifugal & Positive Displacement Marine Pumps 12.2 Valves, Filters, Strainers & Pipeline Identification 12.3 Bilge, Ballast & Oily Water Separator (OWS) Systems 12.4 Steering Gear Systems & Emergency Steering Procedures 12.5 Shipboard Plumbing Repairs, Pipe Clamping & Pipeline Maintenance
13 Chapter 13: Workshop Tools, Fitting, Hot Work & Electrical Safety
13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement 13.2 Power Tools, Grinding, Drilling & Safe Workshop Operations 13.3 Gas Welding, Electric Arc Welding & Hot Work Safety 13.4 Electrical Safety, Isolation, LOTO & Hazards in Machinery Spaces 13.5 Lathe Machine Operations, Centering & Fabrication 13.6 Shipboard Carpentry, Woodworking & Cement Box Emergency Repairs
14 Chapter 14: Engine Room Firefighting, Fixed Systems & Emergency Response
14.1 Machinery Space Fire Hazards & Flammable Liquids Management 14.2 Fixed Fire-Extinguishing Systems: CO2, Water Mist & Hi-Expansion Foam 14.3 Emergency Procedures: Blackout, Flooding, Abandon Ship & Engine Room Safety Drills
13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement
Key Takeaways Explain This Topic AI
Soft vice jaws made of brass, copper, lead, or aluminum must always be fitted over bench vice serrated steel jaws when clamping finished, polished, or soft non-ferrous components to prevent surface scoring.
Hacksaw blades must be installed with teeth pointing forward (away from the handle); cutting pressure is applied strictly on the forward stroke and released on the backward return stroke, selecting 14, 18, 24, or 32 TPI based on stock thickness to maintain at least 2 to 3 teeth in contact.
Files must NEVER be operated without a securely fitted handle to prevent palm puncture wounds; teeth clogged with pinned metal chips must be cleaned using a file card, and cold chisels with mushroomed heads must be removed from use and correctly dressed by a competent person before reuse.
Precision measurement requires selecting the correct instrument: Vernier calipers resolve to 0.02 mm 0.02\text{ mm} 0.02 mm , outside micrometers measure down to 0.01 mm 0.01\text{ mm} 0.01 mm with uniform pressure ensured by a ratchet stop, feeler gauges measure narrow clearance gaps, and dial test indicators (DTI) measure shaft runout and crankshaft web deflection.
Last updated: November 2026
13.1 Workshop Hand Tools, Fitting Practices & Precision Measurement
In a merchant ship's engine room workshop, the General Purpose (GP) Rating is routinely tasked with bench fitting, fabricating replacement brackets, overhauling valve seats, dressing machine parts, and taking precision measurements of engine clearances. Working thousands of nautical miles from shore workshops, seafarers must execute bench work with extreme precision, metallurgical discipline, and unwavering attention to safety.
1. Workshop Hand Tools & Bench Fitting Practices
Bench fitting involves cutting, shaping, and finishing metal components to exact blueprint tolerances using manual hand tools. Safe and effective fitting demands correct tool selection, appropriate cutting lubricants, and strict adherence to safety protocols. BENCH VICE & SOFT JAWS PROTECTION
- +-------------------------------------------------------+
- | Fixed Cast Iron Body |
- | [Hardened Steel Serrated Jaws] |
- | +----------------------------+ |
- | | \\\\ Soft Copper/Brass \\\\ | <--- Sacrificial |
- |======| \\\\ Soft Vice Jaws \\\\ | Protection |
- | +----------------------------+ |
- | [ Machined Workpiece ] |
- | +----------------------------+ |
- | | \\\\ Soft Copper/Brass \\\\ | |
- | +----------------------------+ |
- | [Hardened Steel Serrated Jaws] |
- | Movable Slide & Screw |
- +-------------------------------------------------------+
- The Bench Vice
The bench vice is bolted securely to the workshop bench at elbow height (approximately 1.0 to 1.05 meters 1.0\text{ to }1.05\text{ meters} 1.0 to 1.05 meters above deck level) to provide optimal filing and sawing posture. The vice body is manufactured from heavy cast iron or cast steel, housing a square-thread spindle and replaceable hardened steel jaw plates featuring criss-cross serrated teeth for maximum grip.
Soft Vice Jaws (False Jaws) : When clamping finished, polished, threaded, or soft non-ferrous workpieces (such as brass valve spindles, copper pipes, or aluminum fittings), the hardened serrated steel jaws will permanently crush, indent, and score the component. Trainee ratings must fit soft vice jaws manufactured from copper, brass, lead, aluminum, or fiber over the steel jaws. These softer sacrificial materials cushion the clamping force without indenting precision-machined surfaces.
The Hacksaw: Frame, Blade Selection & Cutting Technique
A workshop hacksaw consists of a tubular steel C-frame (fixed or adjustable) fitted with a pistol grip or straight handle, a threaded wing-nut tensioning stud, and two mounting pins holding a flexible or all-hard high-speed steel (HSS) blade.
Blade Installation : The hacksaw blade must always be installed with its teeth pointing forward (away from the handle) . Hacksaw blades are designed to cut strictly in the pushing direction. The wing nut must be tightened until the blade produces a clear, high-pitched metallic ping when plucked lightly; a slack blade buckles, twists, and snaps, whereas an overtightened blade tears out at the pinholes.
Blade Pitch (Teeth Per Inch - TPI) : Hacksaw blades are classified by the number of teeth per inch ( 25.4 mm 25.4\text{ mm} 25.4 mm ):
Pitch (TPI) Tooth Spacing Recommended Applications & Materials
14 TPI Coarse ( 1.8 mm 1.8\text{ mm} 1.8 mm ) Large cross-sections ( > 25 mm > 25\text{ mm} > 25 mm ), soft solid metals, aluminum, copper, brass, phosphor bronze. Provides large gullets for chip clearance.
18 TPI Medium ( 1.4 mm 1.4\text{ mm} 1.4 mm ) General workshop utility: mild steel solids, cast iron, tool steel bar stock ( 12 to 25 mm 12\text{ to }25\text{ mm} 12 to 25 mm thick). The standard engine room blade.
24 TPI Fine ( 1.0 mm 1.0\text{ mm} 1.0 mm ) Angle iron, steel tubing, pipe walls, structural conduit ( 3 to 6 mm 3\text{ to }6\text{ mm} 3 to 6 mm wall thickness).
32 TPI Extra Fine ( 0.8 mm 0.8\text{ mm} 0.8 mm ) Thin sheet metal, thin-walled tubing, conduit under 3 mm 3\text{ mm} 3 mm thickness, electrical cable casing.
Important
The Golden Rule of Sawing : At least two to three consecutive teeth must be in continuous contact with the workpiece cross-section at all times. If the blade pitch is too coarse for thin metal, the edge of the sheet slips into the tooth gullet, causing the teeth to straddle the edge and shear off instantly.
Correct Sawing Technique : Stand in an athletic, balanced stance with the left foot forward (for a right-handed fitter). Apply steady, moderate downward pressure only on the forward stroke . On the backward return stroke, completely relieve all downward pressure , allowing the teeth to slide lightly across the metal. Dragging a hacksaw blade backward under pressure rapidly dulls and fractures the delicate cutting edges. Maintain a steady cadence of 40 to 50 strokes per minute ; excessive speed generates friction heat that anneals the hardened steel teeth, destroying the blade.
Files: Classification, Techniques & Safety
Files are multi-tooth cutting tools made of high-carbon steel, through-hardened and tempered. The file consists of the tang (the pointed spike inserted into the handle), heel (un-toothed zone near the tang), face (main cutting surface), edge , and point (tip). ANATOMY OF AN ENGINEER'S FILE
- Point Face (Cutting Teeth) Heel Tang
- +-----+------------------------------------------+----+ +------------+
- | | \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ | | | Wooden/ |
- | > | ////////////////////////////////////// | |==| Plastic |
- | | \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ | | | Handle |
- +-----+------------------------------------------+----+ +------------+
- (NEVER USE
- WITHOUT HANDLE!)
Classification by Cross-Sectional Shape :
Flat File : Rectangular cross-section, tapered toward the point; general flat surface work.
Hand File : Rectangular cross-section of uniform width throughout its length; features one safe edge (an edge with no teeth). The safe edge allows filing flat against an internal 90 ∘ 90^\circ 9 0 ∘ shoulder without cutting into or damaging the adjoining vertical face.
Square File : Square cross-section; for filing rectangular slots, keyways, and square holes.
Round File (Rat-Tail) : Circular cross-section; for enlarging circular holes and filing concave radiused fillets.
Half-Round File : Flat on one face and curved convex on the other; versatile for curved contours and flat faces.
Three-Square (Triangular) File : Equilateral triangle cross-section ( 60 ∘ 60^\circ 6 0 ∘ angles); for cleaning acute corners, dovetail slides, and sharpening saw teeth.
Classification by Cut & Spacing :
Cut Pattern : Single-cut files have single rows of parallel teeth cut across the face at 60 ∘ 60^\circ 6 0 ∘ to the center line, producing a smooth, shearing cut ideal for soft metals (brass, bronze, aluminum) and draw filing. Double-cut files have two intersecting rows of teeth (overcut at 70 ∘ 70^\circ 7 0 ∘ and upcut at 51 ∘ 51^\circ 5 1 ∘ ) that break chips into small rhombic diamonds for rapid stock removal on hard steel.
Grade of Coarseness : Classified from coarsest to finest: Rough , Bastard , Second-cut , Smooth , and Dead-Smooth . In marine bench work, the bastard file is used for rapid rough material removal, the second-cut file brings the workpiece close to final dimensions, and the smooth/dead-smooth file delivers precision sizing and surface finish.
Filing Techniques :
Cross Filing : The file is pushed diagonally across the workpiece from corner to corner, alternating diagonal strokes. This technique rapidly establishes a flat plane because crossing stroke patterns visually expose high spots and low hollows.
Draw Filing : The file is gripped with both hands on the blade face, perpendicular to the stroke, and pushed and pulled longitudinally along the length of the workpiece. Draw filing removes file marks left by cross filing, producing an exceptionally fine, satin-smooth finish.
File Maintenance & Pinning : Soft metal filings (especially aluminum, copper, and lead) lodge tightly between the teeth—a defect known as pinning . Pinned particles act as gouging chisels, scratching deep gouges into the workpiece. Trainee ratings must regularly clean the file face using a file card (a wooden paddle faced with stiff wire bristles and fitted with a brass pick) brushed strictly parallel to the rows of teeth.
Mandatory Safety Rule : NEVER use a file without a securely fitted wooden or heavy plastic handle! The pointed steel tang can easily pierce the palm or wrist if the file catches on the work, severing tendons and blood vessels.
Cold Chisels & Hammer Dressing
Cold chisels are forged from high-carbon or chrome-vanadium tool steel with a hardened and tempered cutting edge, used for cutting, chipping, and parting heavy sheet or seized fasteners without applying heat.
Types of Cold Chisels :
Flat Chisel : Broad straight cutting edge for general chipping, trimming sheet metal, and cutting off rusted bolt heads.
Cross-Cut (Cape) Chisel : Narrow cutting edge wider than the blade shank to prevent jamming; used for cutting keyways, grooves, and rectangular channels.
Diamond-Point Chisel : V-shaped nose terminating in a sharp point; used for clearing out sharp 90 ∘ 90^\circ 9 0 ∘ square corners, chipping corner cracks, and drilling lead center holes.
Round-Nose Chisel : Semicircular cutting edge; used for cutting oil grooves in bronze journal bearing shells and chipping internal radiused fillets.
Cutting Angles : For general chipping of mild steel, the chisel cutting edge is ground to an included angle of 60 ∘ 60^\circ 6 0 ∘ . For softer metals like brass and copper, grind to 55 ∘ 55^\circ 5 5 ∘ ; for hard cast iron, grind to 70 ∘ 70^\circ 7 0 ∘ to reinforce the cutting edge.
Mushroom Head Hazard : Repeated hammer blows can spread the striking head into thin, ragged edges. These can break off and cause serious eye or skin injuries. Remove a mushroomed or damaged chisel from use. A competent person should dress off the spread metal and restore the correct striking-head profile without overheating it. Wear suitable eye protection when chipping or dressing tools. COLD CHISEL STRIKING HEAD SAFETY
- DANGEROUS MUSHROOM HEAD DRESSED & CHAMFERED HEAD
- (Flying Shrapnel Hazard) (Safe to Strike)
- /-------\ /-------\
- <| *** |> / \
- <<| ******* |>> <--- Brittle +-----------+
- | | Shards | |
- | Shank | | Shank |
- Scrapers & Surface Plate Alignment
Scrapers are hardened tool steel hand tools used to remove microscopic high spots from flat or curved machine surfaces (such as white-metal crankshaft journal bearings, crosshead slippers, and valve chests) where machine tool grinding is impossible.
Types : Flat scrapers (for flat guide surfaces), half-round scrapers (for concave bearing shells), and three-square (bearing) scrapers.
Prussian Blue Technique : Spread a very thin film of marking blue on the reference surface. Check a flat workpiece against a surface plate ; check a curved bearing against its matching journal or suitable curved master . Move the surfaces lightly together and inspect the transferred high spots. Where hand scraping is specified, a trained fitter removes small amounts from those spots and repeats the check until the required contact pattern and clearance are obtained. Do not scrape a precision bearing lining unless its repair procedure permits it.
Hammers: Ball Peen & Soft Mallets
Ball Peen Hammer : The universal engineer's hammer, classified by head weight ( 0.25 kg 0.25\text{ kg} 0.25 kg to 1.0 kg 1.0\text{ kg} 1.0 kg ). Features a flat striking face with bevelled edges for general striking, and a hemispherical ball peen used for riveting, expanding core plugs, and tapping out paper/Klingerite gaskets against metal flange edges.
Soft-Faced Mallets : Copper, brass, rawhide or nylon faces reduce marking when a permitted light blow is needed on a fitted bolt or machined housing. For bearings, follow the specified press, heating or fitting-tool method. If an impact method is permitted, use the correct sleeve or impact ring against the ring being fitted; do not strike the bearing directly or transmit mounting force through its rolling elements.
Taps, Dies & Thread Cutting Practices
Thread cutting by hand requires taps for internal female threads and dies for external male threads. SET OF THREE HAND TAPS (INTERNAL THREADS)
- 1st Tap: TAPER TAP 2nd Tap: INTERMEDIATE 3rd Tap: BOTTOMING
- (8-10 Threads Chamfered) (3-5 Threads Chamfered) (1-2 Threads Chamfered)
- +---------------------+ +---------------------+ +---------------------+
- | \\\\\\\\\\\\\\\\\ | | ||||||||||||||||| | | ||||||||||||||||| |
- | \\\\\\\\\\\\\\ | | ||||||||||||||| | | ||||||||||||||||| |
- | \\\\\\\\\ | | ||||||||||||| | | ||||||||||||||||| |
- +---------------------+ +---------------------+ +---------------------+
- Long lead starts thread Shorter lead approaches Short lead finishes near
- and can finish a through a blind-hole bottom the blind-hole bottom
- hole (allow lead/chip space)
Set of Three Hand Taps :
First (Taper) Tap : Chamfered over the first 8 to 10 threads at an angle of roughly 4 ∘ 4^\circ 4 ∘ . Starts the thread square to the hole face with a gentle, progressive cut. Behind its lead it can produce the full thread in a suitable through hole.
Second (Intermediate or Plug) Tap : Chamfered over 3 to 5 threads at an angle of roughly 10 ∘ 10^\circ 1 0 ∘ . Its shorter lead allows the full thread to approach closer to the bottom of a blind hole.
Third (Bottoming or Finishing) Tap : Chamfered only over 1 to 2 threads at an angle of 20 ∘ 20^\circ 2 0 ∘ . Finishes the thread nearer the bottom of a blind hole. Allow extra drilled depth for the remaining lead and chips; do not force the tap against the bottom.
Tap Drill Size (TDS) Calculation : If a hole is drilled too small, the tap will bind and snap inside the hole (an engineering nightmare requiring spark erosion or specialized extraction). If drilled too large, the resulting thread depth will be shallow and strip under load. For standard Metric threads: TDS = D − P \text{TDS} = D - P TDS = D − P where TDS \text{TDS} TDS is the tap drill diameter in millimeters, D D D is the nominal major diameter of the thread (e.g., 10 mm 10\text{ mm} 10 mm for an M10 bolt), and P P P is the thread pitch in millimeters ( 1.5 mm 1.5\text{ mm} 1.5 mm for standard M10 coarse). Therefore, TDS = 10 − 1.5 = 8.5 mm \text{TDS} = 10 - 1.5 = 8.5\text{ mm} TDS = 10 − 1.5 = 8.5 mm .
Tapping Technique : Fit the tap into an adjustable bar tap wrench. Verify with an engineer's square that the tap is perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) to the metal face in two planes. Apply appropriate cutting lubricant. Rotate the tap forward by half a turn, then reverse it by a quarter turn . This backward motion snaps off the curled metal chips, clearing the tap flutes and preventing the tap from jamming.
Cutting Lubricants : Use neat cutting oil or sulfurized soluble oil for mild steel; kerosene or tallow for aluminum; operate strictly dry (no lubricant) for cast iron , because cast iron contains free graphite that acts as a dry lubricant, and adding oil creates an abrasive grinding paste that accelerates tool wear.
2. Precision Measuring Instruments
Marine engineering tolerances are measured in hundredths or thousandths of a millimeter. Trainee ratings must master four fundamental precision instruments: Vernier calipers, outside micrometers, feeler gauges, and dial test indicators. VERNIER READING EXAMPLE (SCHEMATIC)
Main scale: 1 mm per division
Vernier zero lies between 34 mm and 35 mm.
The 18th vernier division aligns with a main-scale line.
- 50 vernier divisions span 49 mm: 49 / 50 = 0.98 mm each
- Least count: 1.00 - 0.98 = 0.02 mm
- Reading: 34 + (18 x 0.02) = 34.36 mm
- The Vernier Caliper
The Vernier caliper is a versatile sliding instrument capable of taking three types of dimensions: outside diameters (using lower external jaws), inside diameters (using upper internal jaws/nibs), and hole depths (using the sliding depth gauge bar extending from the beam).
Reading Principle : The main scale is graduated in whole millimeters. The sliding vernier scale divides 49 mm 49\text{ mm} 49 mm into 50 equal divisions. Therefore, the difference between one main scale division ( 1.0 mm 1.0\text{ mm} 1.0 mm ) and one vernier scale division ( 49 / 50 = 0.98 mm 49/50 = 0.98\text{ mm} 49/50 = 0.98 mm ) represents the instrument's least count (resolution) : Least Count = 1.0 mm − 0.98 mm = 0.02 mm ( 1 50 mm ) \text{Least Count} = 1.0\text{ mm} - 0.98\text{ mm} = 0.02\text{ mm} \quad \left(\frac{1}{50}\text{ mm}\right) Least Count = 1.0 mm − 0.98 mm = 0.02 mm ( 50 1 mm )
Reading Procedure :
Read whole millimeters on the main scale immediately to the left of the vernier zero mark.
Scan along the vernier scale until you locate the single graduation line that aligns perfectly coincident with a main scale line.
Multiply that vernier line number by 0.02 mm 0.02\text{ mm} 0.02 mm and add it to the main scale reading. Example: Main scale reads 34 mm 34\text{ mm} 34 mm , vernier line 18 aligns coincidentally: Measurement = 34 + ( 18 × 0.02 ) = 34.36 mm \text{Measurement} = 34 + (18 \times 0.02) = 34.36\text{ mm} Measurement = 34 + ( 18 × 0.02 ) = 34.36 mm .
The Outside Micrometer
Where tolerances demand extreme precision ( 0.01 mm 0.01\text{ mm} 0.01 mm ), the outside micrometer is used. It features a rigid U-shaped cast steel frame, a fixed tungsten-carbide anvil, a movable threaded spindle, a graduated barrel (sleeve), a rotating thimble, and an end ratchet stop. OUTSIDE MICROMETER ANATOMY
- Anvil Spindle Sleeve/Barrel Thimble Ratchet Stop
- +-----+ +---------+ +--------------+ +-------+ +-----+
- | | | | | 0 5 10 | | 25 | | *** |
- +----+ +--+ +======|====|===|=====|--|---20--|----+ *** |
- | | | | | 15 | +-----+
- | Rigid Frame +--------------+ +-------+ (Uniform Force
- +--------------------------------------------------------+ Slip Clutch)
Operating Principle : The micrometer spindle has an internal precision screw thread with a pitch of 0.5 mm 0.5\text{ mm} 0.5 mm —meaning one complete 360 ∘ 360^\circ 36 0 ∘ rotation of the thimble advances or retracts the spindle by exactly 0.5 mm 0.5\text{ mm} 0.5 mm .
Graduations :
The sleeve (barrel) datum line has upper marks indicating whole millimeters ( 1.0 mm 1.0\text{ mm} 1.0 mm ) and lower offset marks indicating half millimeters ( 0.5 mm 0.5\text{ mm} 0.5 mm ).
The beveled circumference of the thimble is divided into 50 equal divisions. Rotating the thimble by one graduation advances the spindle by: Least Count = 0.5 mm 50 = 0.01 mm \text{Least Count} = \frac{0.5\text{ mm}}{50} = 0.01\text{ mm} Least Count = 50 0.5 mm = 0.01 mm
The Ratchet Stop : On the illustrated conventional micrometer, a spring-loaded ratchet limits measuring force, commonly about 5 to 10 N 5\text{ to }10\text{ N} 5 to 10 N . Bring the faces gently into contact and use the ratchet as instructed to obtain consistent force. Do not force the spindle against the work by tightening the thimble. The ratchet reduces force-related errors; clean faces, correct alignment, temperature and reference setting still matter.
Zero or Reference Check : Clean the anvil, spindle and any setting standard. For a 0–25 mm micrometer , close the faces gently using the ratchet and check zero. For a larger-range micrometer , use the correct setting standard or gauge block and check that reference size. If adjustment is needed, follow the instrument's sleeve-setting procedure and recheck it; do not mistake a reference check for a complete calibration.
Feeler Gauges
Feeler gauges consist of a folding set of precision-ground, tempered spring-steel blades stamped with their calibrated thickness (ranging from 0.03 mm 0.03\text{ mm} 0.03 mm to 1.00 mm 1.00\text{ mm} 1.00 mm ).
Shipboard Applications : Used for measuring narrow clearance gaps between flat or curved surfaces:
Main engine bearing clearances (crankpin, crosshead, and main bearings).
Cylinder head inlet and exhaust valve tappet clearances.
Piston ring butt gaps (end clearances inside cylinder liner).
Centrifugal pump impeller casing wear-ring running clearances ( 0.2 to 0.4 mm 0.2\text{ to }0.4\text{ mm} 0.2 to 0.4 mm ).
Usage Discipline : Blades must be wiped clean with a lint-free cloth. Never force a thick blade into a gap; combine two thin blades if an intermediate dimension is required. A correct measurement gives a light, smooth sliding drag ("feel").
Dial Test Indicator (DTI) & Crankshaft Web Deflection
A Dial Test Indicator (DTI) converts small linear axial movements of a spring-loaded stylus or contact plunger into rotary motion of a pointer across a circular graduated dial, magnifying movements through a precision rack-and-pinion or lever gear train. The dial face is graduated in 0.01 mm 0.01\text{ mm} 0.01 mm divisions, with a rotatable bezel for zeroing.
Applications : Mounted on an articulated arm attached to a magnetic base to measure shaft runout, flywheel trueness, pump-to-motor shaft misalignment, and disc brake warping.
Crankshaft Web Deflection Checks : A primary responsibility of marine engineers and ratings during main engine drydocking or scheduled maintenance. As a ship's hull flexes in seaways, or as engine bedplate foundation chocks settle and main bearing white metal wears down, the crankshaft center line loses straightness. Web deflection measurements monitor this condition. CRANKSHAFT WEB DEFLECTION DIAL GAUGE SETUP
- +----------------------+
- | Crankpin |
- +----------+-----------+
- / \
- / \
- +------------------+ +------------------+
- | Crank Web A | | Crank Web B |
- | | | |
- | (-> [ DTI Gauge ] <-) | <--- Gauge placed
- | | | | between webs
- +------------------+ +------------------+
- | |
- v v
- Main Journal Main Journal
- Bearing No. 1 Bearing No. 2
Web Deflection Procedure :
Under the responsible engineer's control, secure the engine against starting and follow the maker's turning-gear and personnel-clearance procedure. Fit the correct deflection gauge between the specified marks on the crank webs, opposite the crankpin. Record the engine temperature, vessel condition and gauge sign convention.
Where the connecting rod obstructs an exact bottom reading, use five positions : the first near-bottom position B1 , one side, T at the top, the opposite side, and the second near-bottom position B2 . Turn in the prescribed direction and stop before the gauge can foul the rod. Record every reading without disturbing the gauge; follow the maker's names, angles and calculation method.
Changes in web opening and closing indicate crankshaft bending and help assess alignment. Compare the calculated deflections with the engine maker's limits and previous readings under comparable conditions. A non-zero result is not automatically a defect, and an excessive result requires investigation of bearings, supports and alignment rather than an unsupported diagnosis of a cracked shaft.