Study guide

9.2 Nozzle Types, Spray Patterns & Droplet Sizing

Indiana Commercial Pesticide Applicator Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Indiana & Federal Regulatory Framework

1.1 Indiana Pesticide Applicator Certification & License Types 1.2 Federal Pesticide Laws & Worker Protection 1.3 Indiana Recordkeeping, Insurance & Enforcement 1.4 Professionalism, Chemical Security & Supervising Others 1.5 How to Study for the Indiana Core Exam

2 Chapter 2: Pest Biology & Integrated Pest Management

2.1 Pest Identification, Life Cycles & Plant Pathology 2.2 Principles & Thresholds of Integrated Pest Management 2.3 Pest Control Tactics & Resistance Management

3 Chapter 3: Pesticide Formulations & Adjuvants

3.1 Liquid Pesticide Formulations 3.2 Dry Formulations, Baits & Fumigants 3.3 Adjuvants, Compatibility & Tank Mixing

4 Chapter 4: Pesticide Label Comprehension & Safety Data Sheets

4.1 Mandatory Label Components & Regulatory Authority 4.2 Signal Words, Precautionary Statements & Hazards 4.3 Directions for Use, REI, PHI & Safety Data Sheets

5 Chapter 5: Human Toxicity, Health Hazards & First Aid

5.1 Toxicity, Hazard & Exposure Routes 5.2 Pesticide Poisoning Symptoms & Cholinesterase Inhibition 5.3 First Aid & Emergency Medical Response Protocols

6 Chapter 6: Personal Protective Equipment & Worker Protection

6.1 Selecting & Using Chemical-Resistant PPE 6.2 Respiratory Protection & Respirator Maintenance 6.3 PPE Care, Laundering & Worker Protection Standard Requirements

7 Chapter 7: Pesticides in the Environment & Drift Management

7.1 Environmental Fate & Water Quality Protection 7.2 Spray Drift Dynamics & Prevention Strategies 7.3 Protecting Non-Target Organisms, Pollinators & Sensitive Sites

8 Chapter 8: Safe Handling, Storage, Transportation & Spill Response

8.1 Safe Transportation & Storage Facility Design 8.2 Mixing, Loading & Container Disposal Procedures 8.3 Pesticide Spill Management: The Three C's & Emergency Reporting

9 Chapter 9: Application Equipment, Nozzle Technology & Calibration Calculations

9.1 Application Equipment Types & Maintenance 9.2 Nozzle Types, Spray Patterns & Droplet Sizing 9.3 Liquid Sprayer Calibration & Mathematical Formulas 9.4 Area Calculations & Tank Mix Math

9.2 Nozzle Types, Spray Patterns & Droplet Sizing

Key Takeaways Explain This Topic AI

Spray nozzles perform three functions: metering flow rate (GPM), atomizing fluid into droplets, and dispersing spray into specific patterns.

Standard flat fans require 30–50% boom overlap, while even flat fans (E/EVE) produce uniform bands and must NEVER be used on broadcast booms.

Air-induction (AI) venturi nozzles generate coarse, air-filled droplets that minimize driftable fines for systemic herbicides, whereas cone nozzles produce fine mists for contact insecticides.

Nozzle material wear resistance follows: Ceramic/Tungsten Carbide > Hardened Stainless > Stainless Steel > Polymer > Brass (fastest wear); replace tips when output exceeds new rating by >10%.

Nozzle nomenclature encodes design, angle, and flow (e.g., XR8004 = Extended Range, 80° fan, 0.40 GPM at 40 PSI); ASABE S572.1 standardizes droplet sizes from Extra Fine to Ultra Coarse.

Last updated: September 2026

9.2 Nozzle Types, Spray Patterns & Droplet Sizing

Core Principle: The spray nozzle is the final, critical link in the pesticide delivery system. It directly controls three parameters vital to application success: the volume of chemical applied per unit area ( metering ), the physical size and drift susceptibility of the spray droplets ( atomization ), and the uniformity of chemical deposition across the target pest or crop ( dispersion ).

Selecting the wrong nozzle type, operating at inappropriate pressure ranges, or neglecting worn nozzle tips leads directly to poor pest control, severe crop phytotoxicity, illegal chemical residues, and catastrophic off-target spray drift. Certified applicators must master nozzle spray geometries, orifice metallurgy, alphanumeric naming standards, and droplet spectrum management.

1. The Three Primary Engineering Functions of Spray Nozzles

Every spray nozzle, regardless of manufacturer or internal configuration, simultaneously performs three foundational tasks: THE THREE NOZZLE FUNCTIONS

1. METERING FLOW RATE (GPM)

  • Controls the volumetric output of spray liquid at a specific operating pressure.
  • Determined precisely by the cross-sectional area of the nozzle orifice.
  • ▼
  • 2. ATOMIZING THE LIQUID STREAM
  • Shears pressurized fluid into a continuous spectrum of microscopic liquid droplets.
  • Controls droplet size distribution (Volume Median Diameter, VMD).
  • ▼
  • 3. DISPERSING DROPLETS INTO PATTERNS
  • Shapes the atomized cloud into geometric footprints (Flat-Fan, Cone, Flooding).
  • Determines spatial distribution and required boom overlap.

2. Comprehensive Taxonomy of Nozzle Spray Patterns

Different pesticide formulations and target pests require distinct spray geometries to achieve biological efficacy while managing drift risks: +-----------------------------------------------------------------------------------------------------------------------+

| SPRAY NOZZLE PATTERN TAXONOMY |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

| Nozzle Pattern | Spray Geometry | Swath Distribution | Primary Field Applications & Constraints |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Standard** | Oval, tapered fan | Heavy in center, | Broadcast boom spraying of herbicides and |
  • | **Flat-Fan** | (65°, 80°, 110°) | tapered at outer edges | fertilizers; requires 30%–50% boom overlap. |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Even** | Rectangular band | Completely uniform from | Band applications over crop rows or along |
  • | **Flat-Fan (E)** | (40°, 80°, 95°) | edge to edge | curbs; NEVER use on broadcast booms! |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Hollow-Cone** | Circular ring | Droplets concentrated | Foliar insecticides and fungicides; dense |
  • | | (Conical sheet) | on outer ring | canopy penetration; high drift risk. |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Full-Cone** | Solid circle | Droplets distributed | High-volume foliar wash; soil-applied |
  • | | (Filled cone) | evenly throughout disc | pre-emergence herbicides; moderate drift. |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Air-Induction** | Tapered fan with | Coarse, air-filled | Systemic herbicides (glyphosate, 2,4-D, |
  • | **(AI / Venturi)**| aspirated air | drift-resistant drops | dicamba); primary drift reduction technology. |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

  • | **Flooding** | Wide-angle fan | Coarse spray; heavy | High-volume liquid fertilizers, pre-plant |
  • | **Flat-Fan (TK)** | (120°–140°) | edges if misaligned | soil herbicides; low pressure (10–25 PSI). |

+-------------------+---------------------+-------------------------+-----------------------------------------------+

1. Standard Flat-Fan Nozzles (Broadcast Application)

Pattern Mechanics: Discharges an elliptical, tapered spray pattern. The spray volume is densest directly beneath the nozzle center and tapers off symmetrically toward both outer edges.

The Overlap Mandate: Because individual flat-fan nozzles deliver tapered edges, they cannot provide uniform coverage alone . On a broadcast boom, adjacent nozzles must be spaced so their spray patterns overlap by 30% to 50% (typically 30% for 80° nozzles and 50% for 110° nozzles).

Boom Height Alignment: Operating the boom too high causes excessive overlap and severe drift; operating the boom too low causes untreated "skips" and heavy streaking. STANDARD FLAT-FAN BOOM OVERLAP (30%–50%)

  • Nozzle 1 Nozzle 2 Nozzle 3
  • │ │ │
  • / \ / \ / \
  • / \ / \ / \
  • / / \ / / \ / / \
  • / / \ / / \ / / \
  • /__/__ _\_______________/__/__ _\_______________/__/__ _\
  • ◄────── Overlap ───────►◄────── Overlap ───────►
  • ═════════════════════════════════════════════════════════ (Target Surface)
  • UNIFORM COMBINED APPLICATION VOLUME
  • 2. Even Flat-Fan Nozzles (Band Application Only)

Pattern Mechanics: Identified by the letter "E" or "EVE" in the part number (e.g., TeeJet 8002E). Discharges a sharp, rectangular spray pattern that delivers an absolutely uniform chemical deposition across the entire band width from edge to edge.

Target Purpose: Engineered exclusively for band applications —applying herbicides in a narrow strip (8 to 15 inches wide) directly over a crop seed row or along curb lines and fence rows.

Caution

NEVER USE EVEN FLAT-FAN NOZZLES ON A BROADCAST BOOM! If an applicator installs even flat-fan nozzles across a broadcast boom, the overlapping edges will receive a 200% double-dose (2× rate) of herbicide, creating severe crop injury and toxic streaks across the entire field!

3. Hollow-Cone and Full-Cone Nozzles

Hollow-Cone (Disc-Core): Liquid is forced through tangential swirl chambers (cores) before exiting a circular orifice disc, producing a hollow ring of very small, high-velocity droplets. Ideal for contact insecticides and protective fungicides where complete coverage of intricate foliage and underside leaf surfaces is required.

Full-Cone: Utilizes an internal vane to distribute droplets uniformly throughout the entire circular footprint. Operates at higher volumes with slightly coarser droplets than hollow-cone tips.

Drift Limitation: Cone nozzles produce high proportions of small droplets ( < 150 μ m < 150\ \mu\text{m} < 150 μ m ) that remain suspended in ambient air, making them highly prone to off-target drift in winds exceeding 5 MPH.

4. Air-Induction (Venturi / AI) Nozzles

Mechanism: Air-induction nozzles incorporate an internal venturi aspirator . Liquid enters a primary metering orifice at high velocity, creating a localized vacuum that draws atmospheric air through dual intake ports. Air and spray liquid mix aggressively inside an internal turbulence chamber before exiting through a larger secondary pattern orifice.

Droplet Characteristics: Produces very large, air-filled ("bubble-filled") droplets. These large droplets possess high mass and momentum, resisting wind deflection and virtually eliminating driftable fines ( < 105 μ m < 105\ \mu\text{m} < 105 μ m ). Upon impact with foliage, the air bubbles collapse, causing the droplet to shatter and spread across the leaf surface rather than bouncing off.

Standard for Systemic Herbicides: Air-induction tips are the industry standard for applying systemic herbicides (such as glyphosate, 2,4-D, and dicamba) where drift mitigation is legally mandated.

5. Flooding Flat-Fan Nozzles

Mechanism: Discharges a wide-angle ( 120 ∘ 120^\circ 12 0 ∘ to 140 ∘ 140^\circ 14 0 ∘ ), low-pressure sheet of liquid that impacts a smooth, angled deflector plate. Produces very large, coarse droplets at low operating pressures (10 to 25 PSI).

Field Application: Designed for applying high-volume liquid fertilizer suspensions, pre-plant soil herbicides, and ice-melt chemicals on wide nozzle spacings (30 to 40 inches). Spray distribution uniformity is lower than standard flat fans.

3. Nozzle Orifice Materials & Wear Resistance Hierarchy

As hundreds of gallons of abrasive chemical suspensions pass through a nozzle orifice under pressure, physical erosion enlarges the orifice opening, distorting the spray pattern and increasing flow rate. NOZZLE MATERIAL WEAR RESISTANCE HIERARCHY

  • CERAMIC / TUNGSTEN CARBIDE (20× to 50× Brass Life) ──► Premium Longevity
  • ▲
  • │ HARDENED STAINLESS STEEL (10× to 15× Brass Life) ──► High Abrasion Resistance
  • │
  • │ STAINLESS STEEL (4× to 6× Brass Life) ──► Standard Commercial
  • │
  • │ POLYMER / ACETAL PLASTIC (2× to 3× Brass Life) ──► Chemical Resistant
  • │

BRASS (1× Baseline Life) ──► FASTEST WEAR / SOFT +-----------------------------------------------------------------------------------------------------------------------+

| NOZZLE ORIFICE MATERIAL COMPARISON MATRIX |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

| Orifice Material | Relative Wear Ratio | Corrosion Resistance | Best Applications & Limitations |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

| **Ceramic /** | **20× – 50×** | **Unsurpassed** | High-acreage custom spraying, abrasive wettable |

| **Tungsten Carbide** | (Longest Life) | (Impervious to acid) | powders, fertilizer slurries. Brittle if struck.|

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

  • | **Hardened** | **10× – 15×** | **Exceptional** | High-pressure spraying, abrasive suspensions, |
  • | **Stainless Steel** | | | commercial broadcast application. High cost. |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

  • | **Standard** | **4× – 6×** | **Excellent** | Standard commercial field booms; handles |
  • | **Stainless Steel** | | | corrosive liquid fertilizers without pitting. |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

  • | **Polymer / Plastic** | **2× – 3×** | **Excellent** | Molded acetal resin; excellent chemical |
  • | **(Nylon/Acetal)** | | (Resists chemicals) | resistance; easily damaged by wire cleaning. |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

  • | **Brass** | **1×** (Baseline | **POOR** | Inexpensive homeowner sprayers; soft metal |
  • | | Fastest Wear) | (Corroded by N-sol) | eroded rapidly by abrasive WP formulations. |

+-----------------------+---------------------+-----------------------+-------------------------------------------------+

The 10% Nozzle Replacement Rule

Over-application resulting from worn nozzle tips costs thousands of dollars in wasted pesticide and risks severe crop injury.

Important

The 10% Replacement Rule: An applicator must calibrate individual nozzle outputs annually and during mid-season inspections. If the measured flow rate (GPM or OPM) of any nozzle tip exceeds the catalog rating of a new nozzle by more than 10% , the nozzle must be discarded and replaced. Furthermore, if the average flow rate of all nozzles on a boom has increased by 10%, the entire set of nozzles must be replaced to maintain pattern uniformity.

4. Nozzle Naming Conventions & Identification Systems

Agricultural nozzle manufacturers (such as TeeJet, Hypro, and Greenleaf) utilize standardized alphanumeric naming conventions stamped directly onto nozzle bodies and tips: DECODING NOZZLE NOMENCLATURE: XR 80 04 VS

  • XR 80 04 VS
  • ┌──────┐ ┌──────┐ ┌──────┐ ┌──────┐
  • │ Type │ │Angle │ │ Flow │ │Mat/ │
  • │Design│ │(Deg) │ │ Rate │ │Color │
  • └──────┘ └──────┘ └──────┘ └──────┘
  • │ │ │ │
  • ▼ ▼ ▼ ▼
  • Extended Range 80° Spray Fan Angle 0.40 GPM at 40 PSI Stainless Steel
  • Flat-Fan Series (Determines Boom Ht) (Standard Flow Rating) (VisiFlo Coded)
  • Breakdown of Part Components

Design / Prefix Letters:

XR = Extended Range Flat-Fan (operates across wide 15–60 PSI range).

TT = Turbo TeeJet (wide-angle flat-fan with pre-orifice for drift reduction).

AI / AIXR = Air-Induction / Air-Induction Extended Range.

DG = Drift Guard (internal pre-orifice to reduce fine droplets).

TJ = TwinJet (twin flat-fan spray patterns angled 60° apart for 3D canopy coverage).

E / EVE = Even Flat-Fan (band spraying only).

Spray Angle (First 2–3 Digits):

Common angles are 65 ∘ 65^\circ 6 5 ∘ , 80 ∘ 80^\circ 8 0 ∘ , and 110 ∘ 110^\circ 11 0 ∘ .

Boom Height Impact: A wider spray angle ( 110 ∘ 110^\circ 11 0 ∘ ) permits the applicator to lower the boom closer to the target canopy (e.g., 20 inches above canopy for 110 ∘ 110^\circ 11 0 ∘ vs. 30 inches for 80 ∘ 80^\circ 8 0 ∘ ). Lower boom height significantly reduces wind drift exposure.

Flow Rate Capacity (Last 2–3 Digits):

Represents volumetric flow rate in Gallons Per Minute (GPM) at a standard benchmark pressure of 40 PSI :

  • 015 = 0.15 GPM at 40 PSI
  • 02 = 0.20 GPM at 40 PSI
  • 03 = 0.30 GPM at 40 PSI
  • 04 = 0.40 GPM at 40 PSI
  • 08 = 0.80 GPM at 40 PSI

Material Suffix Code:

VS = Stainless Steel with VisiFlo color-coding.

VP = Polymer with VisiFlo color-coding.

VK = Ceramic with VisiFlo color-coding.

SS = Solid Stainless Steel; BR = Solid Brass.

ISO Standard Nozzle Color-Coding System

To prevent errors, ISO Standard 10625 assigns specific colors to nozzle bodies based on their rated flow capacity at 40 PSI: +-----------------------------------------------------------------------------------------+

  • | ISO STANDARD NOZZLE COLOR & CAPACITY CODES |
  • +------------------------+-------------------------------+--------------------------------+
  • | ISO Color Code | Flow Capacity at 40 PSI (GPM) | Output in Ounces Per Min (OPM) |
  • +------------------------+-------------------------------+--------------------------------+
  • | **Orange (01)** | 0.10 GPM | 12.8 OPM |
  • | **Green (015)** | 0.15 GPM | 19.2 OPM |
  • | **Yellow (02)** | 0.20 GPM | 25.6 OPM |
  • | **Lilac / Purple (025)**| 0.25 GPM | 32.0 OPM |
  • | **Blue (03)** | 0.30 GPM | 38.4 OPM |
  • | **Red (04)** | 0.40 GPM | 51.2 OPM |
  • | **Brown (05)** | 0.50 GPM | 64.0 OPM |
  • | **Grey (06)** | 0.60 GPM | 76.8 OPM |
  • | **White (08)** | 0.80 GPM | 102.4 OPM |
  • | **Blue-Light (10)** | 1.00 GPM | 128.0 OPM |
  • +------------------------+-------------------------------+--------------------------------+
  • 5. Droplet Sizing Spectrum & ASABE S572.1 Classification

Spray nozzles do not produce droplets of a single uniform size; they generate a continuous spectrum of droplet diameters measured in micrometers / microns ( μ m \mu\text{m} μ m ) ( 1 μ m = 1 / 1 , 000 mm = 1 / 25 , 400 inch 1\ \mu\text{m} = 1/1,000\text{ mm} = 1/25,400\text{ inch} 1 μ m = 1/1 , 000 mm = 1/25 , 400 inch ). A human hair is approximately 100 μ m 100\ \mu\text{m} 100 μ m in diameter. THE DROPLET SIZE SPECTRUM & DRIFT HAZARD

  • FOG / AEROSOLS FINE DROPLETS MEDIUM / COARSE EXTREME / ULTRA
  • (< 60 µm) (60–145 µm) (145–325 µm) (> 400 µm)
  • ┌─────────────────────┬──────────────────────┬──────────────────────┬─────────────┐
  • │ Extreme Drift Hazard│ High Drift Risk │ Ideal Ag Balance │ Zero Drift │
  • │ Greenhouse fogging │ Contact Fungicides │ Systemic Herbicides │ Auxin 2,4-D │
  • └─────────────────────┴──────────────────────┴──────────────────────┴─────────────┘
  • Volume Median Diameter ( V M D VMD V M D or D v 0.5 D_{v0.5} D v 0.5 ​ ) and Driftable Fines

Volume Median Diameter ( V M D VMD V M D ): The droplet diameter where 50% of the total spray volume consists of droplets larger than the VMD, and 50% consists of droplets smaller than the VMD.

Driftable Fines ( < 105 μ m < 105\ \mu\text{m} < 105 μ m ): Droplets smaller than 105 μ m 105\ \mu\text{m} 105 μ m possess negligible settling velocity. They remain suspended in air currents, evaporate before reaching the ground, and drift miles off-target.

ASABE S572.1 Droplet Sizing Categories

The American Society of Agricultural and Biological Engineers (ASABE Standard S572.1) establishes eight standardized droplet size categories, color-coded across all nozzle manufacturers: +-----------------------------------------------------------------------------------------------------------------------+

| ASABE S572.1 DROPLET SIZE CLASSIFICATION SPECTRUM |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| Category Name | ASABE Symbol | Color Code | VMD Range (µm) | Primary Field Pesticide Use |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Extra Fine** | **XF** | **Purple** | $< 60$ | Greenhouse aerosols, space fogging |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Fine** | **F** | **Red** | $60–145$ | Contact insecticides & fungicides |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Medium** | **M** | **Yellow** | $145–225$ | Foliar contact herbicides, turf |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Coarse** | **C** | **Blue** | $225–325$ | Systemic herbicides (glyphosate) |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Very Coarse** | **VC** | **Green** | $325–400$ | Soil pre-emergence, drift buffers |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

  • | **Extremely** | **XC** | **White** | $400–500$ | Dicamba, 2,4-D, buffer zones |
  • | **Coarse** | | | | |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

| **Ultra Coarse** | **UC** | **Black** | $> 500$ | Mandatory auxin drift requirements |

+-------------------+-----------------+-----------------------+-------------------+-------------------------------------+

Tip

The Biological Coverage vs. Drift Trade-Off: Small droplets (Fine to Medium) provide maximum surface coverage and canopy penetration for contact pesticides (which do not move within the plant and require physical contact with every spore or insect). However, they carry extreme drift risk. Large droplets (Coarse to Ultra Coarse) minimize drift risk for systemic pesticides (which translocate throughout the plant vascular system), requiring fewer droplet contacts per square inch to achieve complete control.

Loading diagram... Nozzle Selection & Droplet Sizing Decision Matrix