Study guide
3.1 Minimum Plumbing Facilities & Fixture Count Sizing
Indiana Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation & Trade Mathematics
1.1 Exam Format, Prov Testing Policies & Code References 1.2 Navigating the 2006 IPC & 2012 Indiana Amendments 1.3 Trade Math: Slopes, Head Pressure, Volumes & Fitting Allowances
2 Chapter 2: General Regulations, Structural Safety & Supports
2.1 Piping Protection, Corrosion, Freezing & Sleeving 2.2 Structural Safety: Cutting, Notching & Boring in Joists and Studs 2.3 Pipe Hangers, Brackets, Anchoring & Support Spacing
3 Chapter 3: Plumbing Fixtures, Faucets & Accessibility
3.1 Minimum Plumbing Facilities & Fixture Count Sizing 3.2 Water Closets, Urinals & Flushometer Sizing 3.3 Lavatories, Showers, Bathtubs & Scald Prevention (ASSE 1016/1017)
4 Chapter 4: Traps, Interceptors & Indirect Waste
4.1 Trap Design, Liquid Seal Protection, Primers & Prohibited Traps 4.2 Grease Interceptors, Oil Separators & Sand Traps 4.3 Indirect Waste, Air Gaps, Air Breaks & Food Preparation Waste
5 Chapter 5: Sanitary Drainage: Sizing, Slopes & Materials
5.1 Drainage Fixture Units (DFU) & Horizontal Branch Sizing 5.2 Building Drain & Building Sewer Sizing, Slopes & Velocities 5.3 Drainage Pipe Materials, Solvent Cementing & Mechanical Joints
6 Chapter 6: Sanitary Drainage: Cleanouts, Sumps & Testing
6.1 Cleanout Locations, Sizing, Clearances & Accessibility 6.2 Drainage Sumps, Sewage Ejectors & Backwater Valves 6.3 Drainage System Inspection & Testing (Water, Air & Smoke)
7 Chapter 7: Vents: Principles, Stacks & Terminals
7.1 DWV Venting Principles, Hydraulic Gradients & Trap Protection 7.2 Individual, Common & Relief Vents 7.3 Vent Terminals, Roof Extensions & Frost Closure (IPC Section 904) 7.4 Vent Stacks, Stack Vents, Vent Headers & Waste Stack Vents
8 Chapter 8: Vents: Advanced Systems & Special Venting
8.1 Horizontal & Vertical Wet Venting Systems 8.2 Circuit Venting & Loop Venting Systems 8.3 Combination Waste and Vent Systems & Island Fixture Venting 8.4 Air Admittance Valves (AAVs) & Installation Limits 8.5 Vent Pipe Sizing: Table 916.1, Section 916.2 & Developed Length
9 Chapter 9: Water Supply: Sizing, Distribution & Materials
9.1 Water Service Sizing, Street Pressure & Pressure Regulators 9.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Tables 9.3 Water Distribution Materials, Copper Joining & PEX Systems 9.4 Water Hammer Arrestors & Thermal Expansion Control
10 Chapter 10: Backflow Prevention & Cross-Connection Control
10.1 Cross-Connection Hazards, Backpressure & Backsiphonage 10.2 Backflow Prevention Assemblies: RPZ, DCVA, PVB & Vacuum Breakers 10.3 Containment vs. Isolation, Installation Clearances & Testing
11 Chapter 11: Water Heaters: Sizing, Combustion & Safety
11.1 Water Heater Sizing, Clearances, Drain Pans & Elevation in Garages 11.2 Temperature and Pressure (T&P) Relief Valves & Discharge Piping 11.3 Combustion Air, Draft Hoods & Venting of Fuel-Fired Water Heaters
12 Chapter 12: Storm Drainage Systems & Roof Drainage
12.1 Indiana Rainfall Rates, Projected Roof Area & Roof Drain Sizing 12.2 Vertical Conductors, Downspouts & Horizontal Storm Drains 12.3 Subsoil Drains, Sump Pumps & Secondary Emergency Overflows
13 Chapter 13: Developed Length, Isometric Analysis & Offset Math
13.1 Reading Plumbing Blueprints, Symbols & DWV Riser Diagrams 13.2 Isometric Drawing Interpretation & Three-Dimensional Layouts 13.3 Developed Length Calculations, 45-Degree Offsets & Rolling Offsets
14 Chapter 14: Indiana Plumbing Laws, Rules, Code Amendments & Business
14.1 Indiana Plumbing Commission (IC 25-28.5) & Licensing Standards 14.2 Key Indiana Amendments to the 2006 IPC (675 IAC 16-1.4) 14.3 Plumbing Permits, Local Administrative Rules & Inspections 14.4 Plumbing Business, OSHA Safety & Project Management Fundamentals
3.1 Minimum Plumbing Facilities & Fixture Count Sizing
Key Takeaways Explain This Topic AI
675 IAC 16-1.4-5 deletes IPC Sections 403 and 404 in their entirety and inserts 'See Chapter 29 of the Indiana Building Code,' so minimum and accessible fixture counts are answered from IBC Table 2902.1, not IPC Table 403.1.
Occupant load is calculated by dividing floor area by the occupant load factor in Chapter 10 of the building code, then distributed 50 percent male and 50 percent female unless approved statistics show otherwise.
Fractional fixture results always round up, because a fraction of a water closet cannot be installed.
Separate facilities for each sex are required except for dwelling and sleeping units, structures or tenant spaces with a total occupant load of 15 or fewer, and mercantile occupancies with an occupant load of 100 or fewer.
IPC Section 419.2 survives in Indiana and limits urinal substitution to no more than 67 percent of the required water closets in assembly and educational occupancies; the minimum-fixture table separately requires one custodial service sink in the listed commercial and institutional occupancies.
Last updated: September 2026
Sizing Minimum Plumbing Facilities
Every commercial, industrial, and institutional structure must provide adequate sanitation facilities to protect public health. Under Chapter 4 of the International Plumbing Code (IPC) and the Indiana Plumbing Code (675 IAC 16-1.4), plumbing systems must be engineered with a sufficient number of water closets, urinals, lavatories, drinking fountains, and service sinks. Sizing these fixtures is not an arbitrary design choice; it is a rigid legal requirement dictated by building occupancy classification, floor square footage, and calculated occupant load.
Read this before anything else in this section. 675 IAC 16-1.4-5 deletes IPC Section 403 and Section 404 in their entirety and inserts the single sentence "See Chapter 29 of the Indiana Building Code." Sections 405.2 , 405.3 , 405.3.1 , 410.1 and 410.2 are deleted the same way. That means that in Indiana, minimum fixture counts, accessible facilities, water closet clearances and drinking fountain approval live in Chapter 29 of the Indiana Building Code (675 IAC 13) — specifically Table 2902.1 and Sections 2902.1.1 and 2902.2 — not in the plumbing code.
This still matters for your exam. Prov's reference list lets you substitute the plain 2006 International Plumbing Code for the Indiana Edition, and that model code prints Table 403.1, which is functionally the same table as IBC Table 2902.1. The ratios below are correct either way; what changes is which book you open and which section you cite . Whenever this section says "Table 403.1," read "IBC Table 2902.1" if you are working from the Indiana Edition.
For the Indiana Journeyman Plumber examination, candidates must know how to read the minimum-fixture table, determine occupant loads using building area factors, properly split populations between the sexes, and apply the exceptions for small spaces and single-user restrooms.
Occupant Load Calculations
The total number of plumbing fixtures required for any building begins with establishing its occupant load . Plumbing codes do not define occupant load independently. Model IPC Section 403.1 — and, in Indiana, IBC/Indiana Building Code Section 2902.1 — establishes that the occupant load is determined in accordance with Chapter 10 of the building code .
Occupant load represents the maximum number of people anticipated to occupy a building or specific space at any given time. The fundamental formula for calculating occupant load is: Occupant Load = Floor Area (Square Feet) Occupant Load Factor (Sq. Ft. per Person) \text{Occupant Load} = \frac{\text{Floor Area (Square Feet)}}{\text{Occupant Load Factor (Sq. Ft. per Person)}} Occupant Load = Occupant Load Factor (Sq. Ft. per Person) Floor Area (Square Feet)
Important
Gross Area vs. Net Area: Pay close attention to whether the IBC occupant load factor specifies gross floor area or net floor area. Gross floor area includes the entire space within the inside perimeter of the exterior walls, including corridors, stairwells, closets, and mechanical rooms. Net floor area includes only the actual occupied space, excluding accessory spaces such as hallways, restrooms, utility shafts, and fixed equipment footprints.
- Common Occupant Load Factors (IBC Table 1004.5)
- Business (Group B - Offices): 150 gross sq. ft. per person (or 100 gross sq. ft. under earlier editions)
Mercantile (Group M - Retail): 60 gross sq. ft. per person on the ground floor; 120 gross sq. ft. per person on upper floors or basements
- Assembly, Unconcentrated (Group A - Tables and Chairs / Restaurants): 15 net sq. ft. per person
- Assembly, Concentrated (Group A - Chairs Only / Auditoriums): 7 net sq. ft. per person
- Assembly, Standing Space: 5 net sq. ft. per person
- Educational (Group E - Classrooms): 20 net sq. ft. per person
- Educational (Group E - Vocational / Shops): 50 net sq. ft. per person
- Factory / Industrial (Group F): 100 gross sq. ft. per person
- Storage / Warehouse (Group S): 500 gross sq. ft. per person
- The Gender Distribution Rule
Once the total occupant load is calculated, the fixture-calculation rule (model IPC 403.1.1; Indiana Building Code Section 2902.1.1 ) requires the occupant load to be distributed equally: 50 percent male and 50 percent female , unless statistical documentation approved by the code official proves a different demographic split.
When dividing the total occupant load by two results in a fraction, the fraction must be rounded up to the nearest whole integer for each gender. Furthermore, when calculating required fixtures per gender from Table 403.1 ratios, fractional fixture requirements must always be rounded up to the next whole number. You cannot install a fraction of a water closet.
Step-by-Step Calculation Example:
A single-story commercial office building (Group B) has a gross floor area of 18,000 square feet.
Using an occupant load factor of 150 gross sq. ft. per person: Total Occupants = 18 , 000 150 = 120 occupants \text{Total Occupants} = \frac{18,000}{150} = 120 \text{ occupants} Total Occupants = 150 18 , 000 = 120 occupants
Applying the 50/50 gender split: Male Occupants = 60 ∣ Female Occupants = 60 \text{Male Occupants} = 60 \quad | \quad \text{Female Occupants} = 60 Male Occupants = 60 ∣ Female Occupants = 60
Referencing IPC Table 403.1 for Business Occupancies:
Water Closets: 1 per 25 for the first 50 occupants, and 1 per 50 for the remainder exceeding 50.
For Males (60 occupants): First 50 occupants require 50 / 25 = 2 50 / 25 = 2 50/25 = 2 water closets. Remaining 10 occupants require 10 / 50 = 0.2 10 / 50 = 0.2 10/50 = 0.2 water closets. Rounding up gives 2 + 1 = 3 2 + 1 = 3 2 + 1 = 3 water closets.
For Females (60 occupants): First 50 occupants require 50 / 25 = 2 50 / 25 = 2 50/25 = 2 water closets. Remaining 10 occupants require 10 / 50 = 0.2 10 / 50 = 0.2 10/50 = 0.2 water closets. Rounding up gives 2 + 1 = 3 2 + 1 = 3 2 + 1 = 3 water closets.
Lavatories: 1 per 40 for the first 80 occupants, and 1 per 80 for the remainder exceeding 80. For 60 occupants: 60 / 40 = 1.5 → 2 60 / 40 = 1.5 \rightarrow 2 60/40 = 1.5 → 2 lavatories per sex.
Minimum Fixture Requirements by Occupancy Classification
IPC Table 403.1 establishes specific baseline ratios for water closets, lavatories, bathtubs/showers, drinking fountains, and service sinks across various occupancy groups. Below is a reference summary for primary commercial occupancies frequently tested on the Indiana plumbing exam:
Occupancy Classification Water Closets (Male) Water Closets (Female) Lavatories (Male & Female) Drinking Fountains Service Sinks
- Assembly (A-1) Theaters 1 per 125 1 per 65 1 per 200 1 per 500 1 service sink
- Assembly (A-2) Restaurants/Bars 1 per 75 1 per 75 1 per 200 1 per 500 1 service sink
- Assembly (A-3) Places of Worship 1 per 150 1 per 75 1 per 200 1 per 1,000 1 service sink
Business (Group B) Offices 1 per 25 (first 50); 1 per 50 (remainder) 1 per 25 (first 50); 1 per 50 (remainder) 1 per 40 (first 80); 1 per 80 (remainder) 1 per 100 1 service sink
- Educational (Group E) Schools 1 per 50 1 per 50 1 per 50 1 per 100 1 service sink
- Factory (Group F) Industrial 1 per 100 1 per 100 1 per 100 1 per 400 1 service sink
- Mercantile (Group M) Retail 1 per 500 1 per 500 1 per 750 1 per 1,000 1 service sink
- Storage (Group S) Warehouses 1 per 100 1 per 100 1 per 100 1 per 1,000 1 service sink
Note
Urinal Substitutions: Section 419.2 is one of the few Chapter 4 fixture-count rules Indiana left in the plumbing code. It reads: "In each bathroom or toilet room, urinals shall not be substituted for more than 67 percent of the required water closets in assembly and educational occupancies." Indiana then deleted the last sentence and inserted "See Chapter 29 of the Indiana Building Code," so the substitution allowance for all other occupancies is a building-code question. Urinal substitution only applies to the male fixture count.
Separate Facilities Mandate and Code Exceptions
Model IPC Section 403.2 — Indiana Building Code Section 2902.2 — establishes the general rule: separate toilet facilities must be provided for each sex . Three exceptions matter:
Private Dwellings: Individual dwelling units and sleeping units.
Small Tenant Spaces (Occupant Load ≤ \le ≤ 15): In structures or tenant spaces with a total occupant load (employees plus customers) of 15 or fewer , a single unisex restroom containing one water closet and one lavatory is permitted to serve both sexes.
Mercantile Occupancies (Occupant Load ≤ \le ≤ 100): In Group M mercantile occupancies with an occupant load of 100 or fewer , separate facilities are not required; a single unisex facility complies with code.
Exam Trap Alert: Later IPC and IBC editions raised the small-tenant threshold (for example, to 25 occupants in some occupancies) and added a Business-occupancy exception. Those are later editions . The exam is built on the 2006 code family, where the thresholds are 15 occupants generally and 100 occupants for Group M .
Single-User Unisex and Family Restrooms
Model plumbing and building codes permit single-user (unisex) toilet facilities to satisfy minimum fixture counts. Under the fixture-calculation provisions (model IPC 403.1.2; Indiana Building Code Chapter 29 ), where individual single-occupancy toilet rooms with locking doors are provided:
Each room containing one water closet and one lavatory counts toward the total required fixture tally.
Fixture credit is divided equally: half of the single-user rooms are credited to the male requirement, and half are credited to the female requirement.
If an odd number of unisex rooms is installed, the additional room may be credited to either sex or to the sex with the greater fixture deficit.
Drinking Fountains, Water Coolers & Bottle Fillers
IPC Section 410 is the drinking fountain section, and Indiana deleted both of its subsections — 410.1 (Approval) and 410.2 (Prohibited Location) — replacing each with "See Chapter 29 of the Indiana Building Code." So every drinking fountain rule below is a building-code and accessibility-standard answer in Indiana.
Sizing Ratio: Required counts come from the minimum-fixture table (Table 403.1 / IBC Table 2902.1). Group B and Group E are 1 fountain per 100 occupants ; Groups A-1 and A-2 are 1 per 500; Group F is 1 per 400; Groups A-3, M and S are 1 per 1,000.
High-Low Accessible Pairing: The requirement that drinking fountains serve both people who use a wheelchair and standing persons is an accessibility rule from the building code and ICC A117.1 — not from IPC Section 410. It is normally satisfied with a "high-low" dual-fountain unit or a single bi-level unit that meets both criteria. If an exam item asks for a percentage split, the percentage comes from the building code edition in force, so check the book rather than reciting a number.
Prohibited Locations: Drinking fountains must not be installed inside public toilet rooms or restrooms. This is model IPC 410.2 — the subsection Indiana redirected to the building code.
Substitution with Water Coolers & Bottle Fillers: Substitution of bottle fillers and water dispensers for a portion of the required fountains is an allowance that varies sharply by code edition. Verify it in the adopted Indiana Building Code before relying on it.
Custodial Service Sinks & Lavatory Sizing
The minimum-fixture table (Table 403.1 / IBC Table 2902.1) requires at least one custodial service sink (or approved mop basin) in the commercial and institutional occupancies listed, though not in Group R-3 dwellings:
Location: Service sinks must be installed in a dedicated janitorial closet or maintenance area, provided with hot and cold running water, an approved backflow-protected faucet, and a minimum 3-inch trap and waste connection.
Function: Service sinks prevent the unsanitary practice of emptying mop water, floor washings, and cleaning chemicals into lavatories, water closets, or food preparation sinks.
Lavatory Proportions: Handwashing lavatories are provided according to the minimum-fixture table ratios for the occupancy. Note that Indiana also amended Section 416.5 , adding an exception: an ASSE 1070 point-of-use temperature-limiting device may be omitted if the public hand-washing fixture is supplied with tempered water through an ASSE 1017 master mixing valve.