Study guide

14.3 Plumbing Permits, Local Administrative Rules & Inspections

Indiana Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation & Trade Mathematics

1.1 Exam Format, Prov Testing Policies & Code References 1.2 Navigating the 2006 IPC & 2012 Indiana Amendments 1.3 Trade Math: Slopes, Head Pressure, Volumes & Fitting Allowances

2 Chapter 2: General Regulations, Structural Safety & Supports

2.1 Piping Protection, Corrosion, Freezing & Sleeving 2.2 Structural Safety: Cutting, Notching & Boring in Joists and Studs 2.3 Pipe Hangers, Brackets, Anchoring & Support Spacing

3 Chapter 3: Plumbing Fixtures, Faucets & Accessibility

3.1 Minimum Plumbing Facilities & Fixture Count Sizing 3.2 Water Closets, Urinals & Flushometer Sizing 3.3 Lavatories, Showers, Bathtubs & Scald Prevention (ASSE 1016/1017)

4 Chapter 4: Traps, Interceptors & Indirect Waste

4.1 Trap Design, Liquid Seal Protection, Primers & Prohibited Traps 4.2 Grease Interceptors, Oil Separators & Sand Traps 4.3 Indirect Waste, Air Gaps, Air Breaks & Food Preparation Waste

5 Chapter 5: Sanitary Drainage: Sizing, Slopes & Materials

5.1 Drainage Fixture Units (DFU) & Horizontal Branch Sizing 5.2 Building Drain & Building Sewer Sizing, Slopes & Velocities 5.3 Drainage Pipe Materials, Solvent Cementing & Mechanical Joints

6 Chapter 6: Sanitary Drainage: Cleanouts, Sumps & Testing

6.1 Cleanout Locations, Sizing, Clearances & Accessibility 6.2 Drainage Sumps, Sewage Ejectors & Backwater Valves 6.3 Drainage System Inspection & Testing (Water, Air & Smoke)

7 Chapter 7: Vents: Principles, Stacks & Terminals

7.1 DWV Venting Principles, Hydraulic Gradients & Trap Protection 7.2 Individual, Common & Relief Vents 7.3 Vent Terminals, Roof Extensions & Frost Closure (IPC Section 904) 7.4 Vent Stacks, Stack Vents, Vent Headers & Waste Stack Vents

8 Chapter 8: Vents: Advanced Systems & Special Venting

8.1 Horizontal & Vertical Wet Venting Systems 8.2 Circuit Venting & Loop Venting Systems 8.3 Combination Waste and Vent Systems & Island Fixture Venting 8.4 Air Admittance Valves (AAVs) & Installation Limits 8.5 Vent Pipe Sizing: Table 916.1, Section 916.2 & Developed Length

9 Chapter 9: Water Supply: Sizing, Distribution & Materials

9.1 Water Service Sizing, Street Pressure & Pressure Regulators 9.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Tables 9.3 Water Distribution Materials, Copper Joining & PEX Systems 9.4 Water Hammer Arrestors & Thermal Expansion Control

10 Chapter 10: Backflow Prevention & Cross-Connection Control

10.1 Cross-Connection Hazards, Backpressure & Backsiphonage 10.2 Backflow Prevention Assemblies: RPZ, DCVA, PVB & Vacuum Breakers 10.3 Containment vs. Isolation, Installation Clearances & Testing

11 Chapter 11: Water Heaters: Sizing, Combustion & Safety

11.1 Water Heater Sizing, Clearances, Drain Pans & Elevation in Garages 11.2 Temperature and Pressure (T&P) Relief Valves & Discharge Piping 11.3 Combustion Air, Draft Hoods & Venting of Fuel-Fired Water Heaters

12 Chapter 12: Storm Drainage Systems & Roof Drainage

12.1 Indiana Rainfall Rates, Projected Roof Area & Roof Drain Sizing 12.2 Vertical Conductors, Downspouts & Horizontal Storm Drains 12.3 Subsoil Drains, Sump Pumps & Secondary Emergency Overflows

13 Chapter 13: Developed Length, Isometric Analysis & Offset Math

13.1 Reading Plumbing Blueprints, Symbols & DWV Riser Diagrams 13.2 Isometric Drawing Interpretation & Three-Dimensional Layouts 13.3 Developed Length Calculations, 45-Degree Offsets & Rolling Offsets

14 Chapter 14: Indiana Plumbing Laws, Rules, Code Amendments & Business

14.1 Indiana Plumbing Commission (IC 25-28.5) & Licensing Standards 14.2 Key Indiana Amendments to the 2006 IPC (675 IAC 16-1.4) 14.3 Plumbing Permits, Local Administrative Rules & Inspections 14.4 Plumbing Business, OSHA Safety & Project Management Fundamentals

14.3 Plumbing Permits, Local Administrative Rules & Inspections

Key Takeaways Explain This Topic AI

In Indiana, plumbing permits can be issued only to a licensed Indiana Plumbing Contractor (or qualifying owner-occupants performing work on their personal primary residence where authorized by local ordinance); Journeyman Plumbers cannot pull permits.

Local building departments across Indiana enforce the statewide Indiana Plumbing Code (675 IAC 16) under local administrative ordinances authorized by IC 36-7-8 and coordinated with the State Building Commissioner.

Plumbing construction requires three mandatory inspection milestones: underground/under-slab rough, above-slab framing rough-in (before concealment), and final inspection with fixtures operating.

Local building officials possess statutory authority to issue immediate Stop Work Orders when plumbing work proceeds without permits, employs unlicensed personnel, or poses imminent health hazards.

Under IC 25-1-11-12 the Indiana Plumbing Commission may assess a civil penalty of not more than $1,000 for each violation, in addition to probation, suspension or revocation, and may order consumer restitution.

Last updated: September 2026

14.3 Plumbing Permits, Local Administrative Rules & Inspections

Core Principle: Code compliance is validated through mandatory permits and multi-stage field inspections. Across the State of Indiana, the administrative process ensures that plumbing installations adhere to the Indiana Plumbing Code (675 IAC 16) before piping is buried underground or concealed behind drywall. Permitting authority is strictly restricted to licensed Plumbing Contractors , establishing legal accountability for public health and safety.

Regulatory Authority: State Oversight & Local Building Departments

The enforcement of building and plumbing standards in Indiana operates under a dual-tier framework involving state oversight and local municipal execution: +-------------------------------------------------------------------------+

  • | INDIANA PLUMBING REGULATORY ENFORCEMENT HIERARCHY |
  • +-------------------------------------------------------------------------+
  • | State Level: |
  • | - Fire Prevention and Building Safety Commission (FPBSC) |
  • | - Promulgates 675 IAC 16 (Indiana Plumbing Code) |
  • | - Division of Fire and Building Safety (IDHS) |
  • | - State Building Commissioner issues Construction Design Releases |
  • | (CDR) for Class 1 commercial/industrial structures (675 IAC 12-6) |
  • | |
  • | Local Level: |
  • | - County, City, and Town Building Departments (IC 36-7-8 / IC 36-7-9) |
  • | - Administer local permit applications and collect permit fees |
  • | - Employ certified local building and plumbing inspectors |
  • | - Perform mandatory jobsite rough, underground, and final inspections |
  • | - Issue Stop Work Orders and Certificates of Occupancy (CO) |
  • +-------------------------------------------------------------------------+

Under Indiana Code Title 36, Article 7 (IC 36-7), local units of government (such as the City of Indianapolis / Marion County Department of Business and Neighborhood Services, the Allen County Building Department in Fort Wayne, or the St. Joseph County Building Department in South Bend) are empowered to establish local building departments. While local governments may establish administrative fee structures and contractor registration procedures, no local unit of government may adopt a technical plumbing standard that conflicts with or is less stringent than the statewide rules adopted by the FPBSC .

Permit Authority: Who Can Pull Permits in Indiana?

A central principle of Indiana plumbing law is the strict limitation on who possesses the legal capacity to apply for and pull plumbing permits:

1. Licensed Indiana Plumbing Contractors

Only an individual who holds an active Plumbing Contractor license issued by the Indiana Plumbing Commission—or an authorized corporate officer representing a registered plumbing contracting firm with a designated licensed contractor—may pull plumbing permits. The contractor must provide proof of an active state license. Bond and insurance requirements come from the local ordinance, not from IC 25-28.5 — the statute contains no statewide surety bond amount and no minimum general liability figure. Many Indiana cities and counties require local contractor registration with a bond and a certificate of commercial general liability insurance before they will issue a permit, and the amounts vary. Check the ordinance for the jurisdiction you are permitting in.

2. Journeyman Plumbers Strictly Prohibited

A licensed Journeyman Plumber cannot pull plumbing permits . Under IC 25-28.5-1-2(3) a journeyman plumber works "under the supervision, direction, and responsibility of a licensed plumbing contractor," and IC 25-28.5-1-11 makes it unlawful to act in the capacity of a plumbing contractor without a contractor license. If a journeyman applies for a municipal plumbing permit, the application will be summarily rejected. Performing permitted plumbing work outside the direct employment of a licensed Plumbing Contractor constitutes unlicensed contracting practice.

3. The Homeowner Exemption

Indiana statutes and most municipal ordinances recognize a narrow "Homeowner Exemption." Under this rule, a bona fide property owner may perform plumbing work on their own primary single-family residence without holding a plumbing contractor license, subject to strict conditions:

The property must be a detached single-family home owned and personally occupied by the applicant as their permanent residence. It cannot be applied to rental properties, commercial buildings, multi-family apartment complexes, or homes constructed for speculative resale.

The homeowner must personally perform the physical labor without hiring unlicensed third parties.

The homeowner must submit plans, apply for the homeowner plumbing permit, pay municipal fees, and successfully schedule and pass all required rough and final code inspections before covering any piping or occupying the structure.

Permit Applications & Plan Submissions

Before initiating plumbing work (except for minor emergency repairs like clearing stoppages or replacing existing faucet washers), the plumbing contractor must submit a formal permit application to the local authority having jurisdiction (AHJ).

Commercial Plan Review & Construction Design Releases (CDR)

For Class 1 structures (commercial buildings, churches, schools, restaurants, and multi-family residential buildings containing three or more dwelling units), plans must first be submitted to the Indiana Department of Homeland Security (IDHS) Division of Fire and Building Safety. Under 675 IAC 12-6 , the State Building Commissioner reviews the engineering plans for compliance with structural, accessibility, life safety, and mechanical codes. Upon approval, the state issues a Construction Design Release (CDR) . The local building department will not issue a local plumbing permit for a Class 1 structure until the contractor provides the valid state CDR number.

Required Document Submittals

Permit applications typically require the submission of:

Architectural floor plans showing the location, type, and layout of all plumbing fixtures.

Three-dimensional isometric riser diagrams showing sanitary drainage, waste, and vent pipe diameters, developed lengths, and cleanouts.

Water supply distribution schematics showing water meter size, service line diameter, and developed lengths.

Complete fixture unit calculations (Drainage Fixture Units [DFUs] and Water Supply Fixture Units [WSFUs]).

Backflow prevention schedules detailing assembly types, ASSE standard numbers, and hazard ratings.

Mandatory Plumbing Inspection Milestones

Plumbing installations must be verified through physical on-site inspections conducted by municipal or county code officials. Indiana plumbing practice mandates three sequential inspection milestones: +-------------------------------------------------------------------------+

  • | MANDATORY PLUMBING INSPECTION MILESTONES |
  • +-------------------------------------------------------------------------+
  • | PHASE 1: UNDERGROUND / UNDER-SLAB ROUGH INSPECTION |
  • | - Scheduled when building sewers and sub-slab piping are installed |
  • | - Trenches open, full bedding visible, joints exposed |
  • | - Hydrostatic water test: minimum 10-foot head of water |
  • | - CONCRETE CANNOT BE POURED UNTIL THIS INSPECTION PASSES |
  • | |
  • | PHASE 2: ABOVE-SLAB ROUGH-IN INSPECTION (BEFORE CONCEALMENT) |
  • | - Scheduled when DWV stacks, vents, and water lines are framed in |
  • | - Structural nail plates installed; pipe hangers secured |
  • | - DWV water test (10-ft head) or metallic air test (5 psi) |
  • | - Water supply test (working pressure or 50 psi air on PEX/copper) |
  • | - DRYWALL AND INSULATION CANNOT BE INSTALLED UNTIL APPROVED |
  • | |
  • | PHASE 3: FINAL INSPECTION |
  • | - Scheduled when all construction is finished and building ready |
  • | - All fixtures set, connected, caulked, and fully operational |
  • | - Water heaters vented, relief valves piped, combustion air verified |
  • | - Backflow prevention assemblies tested by certified tester |
  • | - REQUIRED FOR ISSUANCE OF CERTIFICATE OF OCCUPANCY (CO) |
  • +-------------------------------------------------------------------------+
  • 1. Underground / Under-Slab Rough Inspection

The underground inspection occurs after the building sewer, building drain, sub-slab water service, and under-floor soil and waste branches have been laid in trenches, but before any backfilling or concrete pouring .

Visual Verification: The inspector examines pipe slope (minimum 1/4 inch per foot for pipes 2 inches or smaller; 1/8 inch per foot for pipes 3 to 6 inches where allowed), bed compaction (uniform gravel or crushed stone bedding), pipe sleeving through exterior foundation walls (leaving 2 inches of radial clearance), and fitting selection (long-sweep bends and wyes; no short-radius quarter bends on horizontal drainage).

Mandatory Testing: The system must be hydrostatically tested by filling the underground piping with water to a level at least 10 feet above the highest point of the installation (or to the top of a 10-foot vertical test standpipe) for a minimum of 15 minutes without any drop in water level.

2. Rough-in (Above-Slab / Framing) Inspection

The rough-in inspection is conducted after all DWV stacks, fixture branch lines, roof vent penetrations, water distribution piping, and shower/tub rough-in valves have been installed within wood or steel framing, but before any insulation, wallboard, drywall, or ceilings are applied .

Visual Verification: The inspector verifies proper hanger spacing, structural integrity (ensuring joists and studs are not over-notched or over-bored in violation of structural codes), installation of 16-gauge steel protection shield plates where piping passes within 1-1/2 inches of a framing edge, correct trap arm developed lengths, and roof vent frost closure sizing.

Mandatory Testing: The DWV system must be subjected to a 10-foot water head test. Water supply lines must be pressure tested to system working pressure, or pneumatic testing up to 50 psi on approved PEX/copper piping.

3. Final Inspection

The final inspection occurs after the building is completed and all trades have finished their work. All plumbing fixtures (toilets, sinks, showers, bathtubs, drinking fountains, water heaters) must be set, securely anchored, caulked to finished surfaces, and connected to water supplies and drainage.

Operational Testing: The inspector observes fixture operation, verifies that water closets flush completely and refill their trap seals without leaking, checks that hot water is supplied to the left side of faucets, tests anti-scald shower valves (maximum 120°F water delivery), verifies T&P relief valve discharge lines (terminating indirectly within 6 inches of the floor or drain), and confirms that certified test reports for backflow assemblies are present.

Certificate of Occupancy: Successful passage of the final plumbing inspection is a mandatory statutory prerequisite for the local building department to issue a Certificate of Occupancy (CO) , allowing the building to be legally occupied.

Stop Work Orders, Appeals & Disciplinary Sanctions

When plumbing work departs from statutory standards or code compliance, administrative authorities possess powerful enforcement mechanisms.

Stop Work Orders

Under local building ordinances and the Indiana General Administrative Rules, a building inspector who discovers plumbing work being performed without a permit, executed by unlicensed individuals, or presenting an imminent health or structural hazard is authorized to post a formal Stop Work Order on the jobsite. Once posted:

All plumbing construction on that site must halt immediately.

Performing any further work before receiving written authorization from the building official constitutes a direct municipal violation.

Each day work continues in violation of a Stop Work Order incurs cumulative civil fines.

Administrative Appeals & Code Variances

If a plumbing contractor disputes a local inspector's interpretation of the plumbing code, they may appeal the determination:

Local Board of Appeals: The contractor may appeal to the municipal or county building board of appeals.

State Variance Petition (675 IAC 12-5): If strict compliance with a code section creates an undue hardship and an engineered alternative provides equivalent safety, the contractor and design professional may petition the Fire Prevention and Building Safety Commission (FPBSC) for a formal state code variance .

Disciplinary Sanctions under IC 25-1-11 & IC 25-28.5

The Indiana Plumbing Commission exercises disciplinary authority over all plumbing licensees under Indiana Code Title 25, Article 1, Chapter 11 (IC 25-1-11) (Uniform Professional Disciplinary Actions). Disciplinary grounds include:

Practicing fraud, deceit, or material misrepresentation in obtaining a license or permit.

Aiding or abetting an unlicensed person to practice plumbing (such as a licensed contractor "lending" their license to an unlicensed company, or leaving apprentices unsupervised).

Gross incompetence, negligence, or repeated, willful code violations endangering public health.

Conviction of a crime bearing a direct relationship to professional practice. +-------------------------------------------------------------------------+

  • | INDIANA PLUMBING COMMISSION SANCTIONS (IC 25-1-11) |
  • +-------------------------------------------------------------------------+
  • | Written Censure / Letter of Reprimand |
  • | Probationary Licensure (with mandatory reporting or oversight) |
  • | Civil Penalties up to $1,000 PER VIOLATION |
  • | License Suspension (temporary cessation of practice) |
  • | Permanent License Revocation (complete cancellation of credential) |
  • | Injunctions & Misdemeanor Criminal Referrals for Unlicensed Practice |
  • +-------------------------------------------------------------------------+

Under IC 25-1-11-12, the Commission may assess civil penalties up to $1,000 for each violation . Furthermore, practicing plumbing without a license under IC 25-28.5-1-31 is classified as a Class A misdemeanor , punishable by criminal fines and up to one year in jail.

Plumbing Inspection Compliance Matrix

Inspection Phase When Scheduled Primary Piping Inspected Required Pressure Test Critical Failure Modes

Underground / Under-Slab Trenches open; before backfill or slab pour Building sewer, building drain, sub-slab water service 10-foot head of water for 15 minutes Inadequate fall/slope; uncompacted bedding; fitting leaks; missing foundation sleeves

Above-Slab Rough-In Framing complete; before insulation/drywall DWV stacks, branches, fixture vents, water supply lines 10-foot head of water on DWV; working pressure or 50 psi air on water Over-notched structural joists; missing nail protection plates; unvented fixture arms

Final Inspection Building finished; fixtures installed Fixtures, faucets, water heaters, backflow preventers System working operating pressure Cross-connections; leaking trap seals; hot water over 120°F in showers; unpiped T&P relief valve