Study guide

9.1 Water Service Sizing, Street Pressure & Pressure Regulators

Indiana Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation & Trade Mathematics

1.1 Exam Format, Prov Testing Policies & Code References 1.2 Navigating the 2006 IPC & 2012 Indiana Amendments 1.3 Trade Math: Slopes, Head Pressure, Volumes & Fitting Allowances

2 Chapter 2: General Regulations, Structural Safety & Supports

2.1 Piping Protection, Corrosion, Freezing & Sleeving 2.2 Structural Safety: Cutting, Notching & Boring in Joists and Studs 2.3 Pipe Hangers, Brackets, Anchoring & Support Spacing

3 Chapter 3: Plumbing Fixtures, Faucets & Accessibility

3.1 Minimum Plumbing Facilities & Fixture Count Sizing 3.2 Water Closets, Urinals & Flushometer Sizing 3.3 Lavatories, Showers, Bathtubs & Scald Prevention (ASSE 1016/1017)

4 Chapter 4: Traps, Interceptors & Indirect Waste

4.1 Trap Design, Liquid Seal Protection, Primers & Prohibited Traps 4.2 Grease Interceptors, Oil Separators & Sand Traps 4.3 Indirect Waste, Air Gaps, Air Breaks & Food Preparation Waste

5 Chapter 5: Sanitary Drainage: Sizing, Slopes & Materials

5.1 Drainage Fixture Units (DFU) & Horizontal Branch Sizing 5.2 Building Drain & Building Sewer Sizing, Slopes & Velocities 5.3 Drainage Pipe Materials, Solvent Cementing & Mechanical Joints

6 Chapter 6: Sanitary Drainage: Cleanouts, Sumps & Testing

6.1 Cleanout Locations, Sizing, Clearances & Accessibility 6.2 Drainage Sumps, Sewage Ejectors & Backwater Valves 6.3 Drainage System Inspection & Testing (Water, Air & Smoke)

7 Chapter 7: Vents: Principles, Stacks & Terminals

7.1 DWV Venting Principles, Hydraulic Gradients & Trap Protection 7.2 Individual, Common & Relief Vents 7.3 Vent Terminals, Roof Extensions & Frost Closure (IPC Section 904) 7.4 Vent Stacks, Stack Vents, Vent Headers & Waste Stack Vents

8 Chapter 8: Vents: Advanced Systems & Special Venting

8.1 Horizontal & Vertical Wet Venting Systems 8.2 Circuit Venting & Loop Venting Systems 8.3 Combination Waste and Vent Systems & Island Fixture Venting 8.4 Air Admittance Valves (AAVs) & Installation Limits 8.5 Vent Pipe Sizing: Table 916.1, Section 916.2 & Developed Length

9 Chapter 9: Water Supply: Sizing, Distribution & Materials

9.1 Water Service Sizing, Street Pressure & Pressure Regulators 9.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Tables 9.3 Water Distribution Materials, Copper Joining & PEX Systems 9.4 Water Hammer Arrestors & Thermal Expansion Control

10 Chapter 10: Backflow Prevention & Cross-Connection Control

10.1 Cross-Connection Hazards, Backpressure & Backsiphonage 10.2 Backflow Prevention Assemblies: RPZ, DCVA, PVB & Vacuum Breakers 10.3 Containment vs. Isolation, Installation Clearances & Testing

11 Chapter 11: Water Heaters: Sizing, Combustion & Safety

11.1 Water Heater Sizing, Clearances, Drain Pans & Elevation in Garages 11.2 Temperature and Pressure (T&P) Relief Valves & Discharge Piping 11.3 Combustion Air, Draft Hoods & Venting of Fuel-Fired Water Heaters

12 Chapter 12: Storm Drainage Systems & Roof Drainage

12.1 Indiana Rainfall Rates, Projected Roof Area & Roof Drain Sizing 12.2 Vertical Conductors, Downspouts & Horizontal Storm Drains 12.3 Subsoil Drains, Sump Pumps & Secondary Emergency Overflows

13 Chapter 13: Developed Length, Isometric Analysis & Offset Math

13.1 Reading Plumbing Blueprints, Symbols & DWV Riser Diagrams 13.2 Isometric Drawing Interpretation & Three-Dimensional Layouts 13.3 Developed Length Calculations, 45-Degree Offsets & Rolling Offsets

14 Chapter 14: Indiana Plumbing Laws, Rules, Code Amendments & Business

14.1 Indiana Plumbing Commission (IC 25-28.5) & Licensing Standards 14.2 Key Indiana Amendments to the 2006 IPC (675 IAC 16-1.4) 14.3 Plumbing Permits, Local Administrative Rules & Inspections 14.4 Plumbing Business, OSHA Safety & Project Management Fundamentals

9.1 Water Service Sizing, Street Pressure & Pressure Regulators

Key Takeaways Explain This Topic AI

Available static water pressure from a municipal water main is converted to dynamic residual pressure during flow as friction head losses occur across the water service pipe, meter, fittings, valves, and elevation changes.

IPC Table 604.3 sets the required flow rate and flow pressure at each fixture supply outlet: 8 psi for a close-coupled tank water closet, lavatory, bathtub, sillcock and residential sink; 20 psi for a one-piece tank water closet and a temperature-controlled shower; 15 psi for a urinal valve, a flushometer tank and a siphonic flushometer water closet; and 25 psi for a blowout flushometer water closet.

IPC Section 604.8 strictly mandates the installation of an approved pressure-reducing valve (PRV conforming to ASSE 1003) equipped with an integral strainer whenever municipal static water pressure exceeds 80 psi (552 kPa).

Vertical elevation changes alter water pressure by exactly 0.433 psi per foot of head (1 psi = 2.31 feet of water column), requiring plumbers to subtract 0.433 psi per foot of elevation rise and add 0.433 psi per foot of drop.

In sizing water service piping from the corporation stop to the building control valve, total available pressure must be budgeted across elevation head loss, meter head loss, friction loss through equivalent pipe lengths, and minimum required fixture residual pressure.

Last updated: September 2026

9.1 Water Service Sizing, Street Pressure & Pressure Regulators

Core Principle: A potable water distribution system must deliver an adequate volume of water at sufficient pressure to operate all fixtures simultaneously without exceeding safe velocity limits or causing hydraulic destruction. Under Chapter 6 of the International Plumbing Code (IPC) and the Indiana Plumbing Code (675 IAC 16-1.4), water service design requires balancing municipal supply pressure against friction losses, meter restrictions, and elevation changes, while capping maximum system pressure at 80 psi (552 kPa) to protect plumbing infrastructure.

Anatomy of the Municipal Water Service Connection

The water service pipe is the exterior supply pipe extending from the municipal water main or private potable water source to the inside of the building foundation wall or building control valve. In a standard municipal utility connection, water travels through several critical control and metering components before entering the interior distribution system: +-----------------------------------------------------------------------------------------+

  • | MUNICIPAL WATER SERVICE PIPING PATHWAY |
  • +-----------------------------------------------------------------------------------------+
  • | MUNICIPAL | CORPORATION | SERVICE LATERAL | CURB STOP | METER VAULT / | BUILDING |
  • | WATER MAIN | STOP | (GOOSENECK) | & CURB BOX | INTERIOR METER | SHUTOFF |
  • | (City Street)| (Tap on Main)| (Copper Type K) | (Property Line) | (With Checks) | VALVE |
  • +-----------------------------------------------------------------------------------------+

Corporation Stop (Corp Stop): A specialized bronze ball or plug valve tapped directly into the pressurized municipal water main under pressure using a tapping machine. When tapping rigid water mains, an expansion loop or curved "gooseneck" (typically flexible Type K soft copper annealed tubing bent into an S-curve) is installed immediately downstream of the corporation stop to prevent earth settlement and thermal expansion from shearing the tap connection.

Water Service Lateral: The underground buried pipe carrying water from the main to the property boundary. Table 605.3 lists the approved water service materials. Indiana amended Table 605.3 at 675 IAC 16-1.4-7(c): under "copper or copper alloy tubing," the entry "M or WM" is deleted , so Type M copper is not an approved water service material in Indiana . Indiana also deletes Section 605.3.1 without substitution (675 IAC 16-1.4-7(d)). Bury depth is not a frost-line calculation in Indiana: Section 305.6.2 and Table 305.6.2 set a county-specific depth of 36, 42 or 48 inches measured from finished grade to the top of the water pipe.

Curb Stop and Curb Box (Buffalo Box): A heavy-duty bronze valve located near the property line or utility easement, operated from ground level via a long key inserted into a cast-iron sleeve (curb box). The curb stop serves as the utility's emergency shutoff to isolate the property without entering the building.

Water Meter: A positive-displacement (oscillating piston or nutating disc) or turbine meter installed in an exterior underground meter pit or inside the building's utility room. Meters create significant friction head loss, which must be deducted from available street pressure during hydraulic sizing.

Main Building Control Valve: An accessible full-port shutoff valve (typically a full-port ball valve conforming to MSS SP-110) installed immediately inside the building foundation wall to allow occupants to isolate the entire plumbing system.

Static Pressure vs. Dynamic Residual Pressure

Plumbing calculations distinguish between water at rest and water in motion. Confusing static and dynamic pressure leads to severe sizing errors, noisy pipes, and fixture starvation:

Static Pressure: The hydrostatic pressure exerted by water against pipe walls when zero water is flowing throughout the system. Static pressure is governed entirely by the height of the municipal water tower, utility booster pumps, or elevation differentials between the supply reservoir and the fixture.

Dynamic (Residual) Pressure: The actual pressure remaining in the water column when water is actively flowing through the distribution piping. As water moves, friction against the interior pipe wall, turbulence through valves and fittings, and meter restrictions consume potential energy, reducing the available pressure. Residual Flow Pressure = Static Street Pressure − Δ P elevation − Δ P meter − Δ P friction − Δ P devices \text{Residual Flow Pressure} = \text{Static Street Pressure} - \Delta P_{\text{elevation}} - \Delta P_{\text{meter}} - \Delta P_{\text{friction}} - \Delta P_{\text{devices}} Residual Flow Pressure = Static Street Pressure − Δ P elevation ​ − Δ P meter ​ − Δ P friction ​ − Δ P devices ​

Plumbers verify static pressure by threading a Bourdon tube test gauge onto an unpressurized hose bibb with all fixtures closed. Dynamic pressure is measured by opening adjacent fixtures and observing the pressure drop on the test gauge while water is flowing at peak design demand.

Minimum Fixture Flow Pressures (IPC Table 604.3)

Section 604.3 requires the water distribution system to be designed and pipe sizes selected so that at peak demand the capacities at the fixture supply pipe outlets are not less than shown in Table 604.3 . Fixtures and appliances not listed follow the manufacturer's installation instructions.

Two numbers that catch candidates out. In Table 604.3 the siphonic flushometer water closet requires 25 gpm at 15 psi , while the blowout flushometer water closet requires 35 gpm at 25 psi . The 25 psi figure belongs to the blowout fixture, not the siphonic one. Likewise a close-coupled tank water closet needs only 8 psi , while a one-piece tank water closet needs 20 psi , and a flushometer tank water closet needs 15 psi .

Plumbing Fixture / Appliance Minimum Flow Rate (gpm) Minimum Dynamic Flow Pressure (psi) Standard Supply Inlet Size (Inches)

  • Bathtub Faucet 4.0 8 1 / 2 1/2 1/2
  • Bidet Faucet 2.0 4 3 / 8 3/8 3/8
  • Commercial Flushometer (Blowout Water Closet) 35.0 25 1 1 1
  • Commercial Flushometer (Siphonic Water Closet) 25.0 15 1 1 1
  • Commercial Flushometer (Urinal) 15.0 15 3 / 4 3/4 3/4
  • Water Closet, Tank, Close Coupled 3.0 8 3 / 8 3/8 3/8
  • Lavatory Faucet 2.0 8 3 / 8 3/8 3/8
  • Water Closet, Flushometer Tank 1.6 15 3 / 8 3/8 3/8
  • Water Closet, Tank, One Piece 6.0 20 3 / 8 3/8 3/8
  • Shower, Temperature Controlled 3.0 20 1 / 2 1/2 1/2
  • Sillcock / Hose Bibb 5.0 8 1 / 2 1/2 1/2
  • Dishwasher, Residential 2.75 8 1 / 2 1/2 1/2
  • Sink, Service 3.0 8 1 / 2 1/2 1/2
  • Drinking Fountain 0.75 8 3 / 8 3/8 3/8
  • Sink, Residential 2.5 8 1 / 2 1/2 1/2
  • Shower 3.0 8 1 / 2 1/2 1/2
  • Combination Fixture 4.0 8 1 / 2 1/2 1/2
  • Laundry Tray 4.0 8 1 / 2 1/2 1/2

Important

The Flushometer Threshold: most ordinary fixtures (a close-coupled tank water closet, a lavatory, a bathtub, a sillcock, a residential sink, a standard shower) require only 8 psi of flow pressure in Table 604.3. Commercial flushometer valves demand 15 psi (siphonic) to 25 psi (blowout) while instantaneously passing 25 to 35 gpm, and a temperature-controlled shower and a one-piece tank water closet both need 20 psi . Designing a water service for a building with flushometer valves therefore takes substantially larger pipe and higher residual pressure than the same building on flush tanks.

Note that the last column above is not part of Table 604.3 — the minimum fixture supply sizes come from Table 604.5 , reproduced in section 9.2. Table 604.3 gives only flow rate and flow pressure.

Maximum Allowable Static Pressure & PRVs (IPC Section 604.8)

While insufficient pressure causes fixture starvation, excessive pressure destroys plumbing fixtures and piping infrastructure. Under IPC Section 604.8 , the maximum allowable static pressure in any potable water distribution system is 80 psi (552 kPa) .

Hazards of Excessive Pressure (> 80 psi)

When municipal water mains operate above 80 psi (often exceeding 100 to 140 psi in low-lying valley areas or near booster pumping stations), unreduced pressure causes severe structural and mechanical failures:

Accelerated Erosion-Corrosion: High pressure forces water through valves and elbows at velocities exceeding code limits, stripping the internal protective oxide film from copper piping (wire-drawing).

Violent Water Hammer: Rapid valve closures generate extreme acoustic shock waves that hammer against pipe walls and loosen hangers.

Component Ruptures: Washing machine rubber hoses, plastic toilet fill valves, and water filtration housings burst under prolonged high pressure.

Relief Valve Weeping: Water heater temperature and pressure (T&P) relief valves lift and discharge water onto floors.

Splashing and Water Waste: Faucets splash violently upon opening, wasting potable water and exceeding fixture flow ratings.

Pressure-Reducing Valves (PRVs per ASSE 1003)

Under IPC Section 604.8, whenever static water pressure from the municipal main or private supply exceeds 80 psi , an approved pressure-reducing valve (PRV) conforming to ASSE 1003 must be installed immediately downstream of the building shutoff valve. PRESSURE-REDUCING VALVE (ASSE 1003)

  • Adjusting Bolt & Locknut
  • | |
  • +--+--+--+
  • | SPRING |
  • +--+--------+--+
  • | DIAPHRAGM |
  • High Pressure Inlet +------+-------+ Low Pressure Outlet
  • (e.g., 110 psi) | (Regulated, e.g., 55 psi)
  • ===============>----+ +------+------+ +------------------>
  • | | VALVE STEM | |
  • +-+----+-------------+----+-+
  • | [STRAINER SCREEN] | (Integral Bypass
  • | (Catches Scale/Grit) | Check Valve)
  • +-------------------------+

Design & Operation: A direct-acting PRV utilizes an internal spring-loaded elastomeric diaphragm balanced against a valve seat orifice. Downstream pressure acts against the underside of the diaphragm. When downstream pressure drops (faucets open), the spring pushes the valve open to maintain flow. When flow stops, downstream pressure pushes the diaphragm upward, closing the valve seat to maintain the set static pressure.

Integral Strainer Requirement: ASSE 1003 requires an integral or immediately upstream removable strainer screen. Municipal water mains frequently carry rust, welding slag, sand, and mineral scale; without a strainer, grit lodges between the PRV seat and disc, preventing valve closure and causing downstream pressure to creep up to full street pressure.

Recommended Pressure Setting: Most commercial PRVs are factory-preset to 50 psi , with an adjustable field range of 25 to 75 psi . The optimal trade working range for residential and light commercial systems is 45 to 60 psi .

Thermal Expansion & Bypass: Most modern ASSE 1003 PRVs incorporate an internal bypass check valve. This bypass allows thermal expansion pressure generated by a water heater to bleed back into the municipal main only if internal building pressure exceeds street pressure. However, if municipal street pressure is higher than the relief threshold, or if a backflow preventer is installed upstream, the bypass cannot function, creating a closed system that mandates an expansion tank.

Elevation Head Loss and Gain Calculations

Water is a heavy physical fluid. Because of gravity, raising water vertically requires energy, causing an immediate pressure drop. Conversely, water dropping vertically downward gains hydrostatic pressure.

The Fundamental Hydrostatic Constant ( 0.433 psi/ft 0.433 \text{ psi/ft} 0.433 psi/ft )

A cubic foot of pure water at standard temperature ( 62.4 ∘ F 62.4^\circ\text{F} 62. 4 ∘ F ) weighs 62.4 pounds . A column of water measuring 1 foot tall with a base of 1 square foot ( 144 square inches 144 \text{ square inches} 144 square inches ) exerts 62.4 pounds of total force across that base. To calculate the pressure exerted on a single square inch: Hydrostatic Pressure Factor = 62.4 lbs 144 in 2 = 0.4333... ≈ 0.433 psi per foot of vertical elevation \text{Hydrostatic Pressure Factor} = \frac{62.4 \text{ lbs}}{144 \text{ in}^2} = 0.4333... \approx 0.433 \text{ psi per foot of vertical elevation} Hydrostatic Pressure Factor = 144 in 2 62.4 lbs ​ = 0.4333... ≈ 0.433 psi per foot of vertical elevation Inverse Head Factor = 1 psi 0.4333 psi/ft = 2.308... ≈ 2.31 feet of head per 1 psi \text{Inverse Head Factor} = \frac{1 \text{ psi}}{0.4333 \text{ psi/ft}} = 2.308... \approx 2.31 \text{ feet of head per 1 psi} Inverse Head Factor = 0.4333 psi/ft 1 psi ​ = 2.308... ≈ 2.31 feet of head per 1 psi

Vertical Rise (Going UP): Deduct 0.433 psi for every 1 foot of vertical rise ( h h h ): Δ P loss = h × 0.433 psi \Delta P_{\text{loss}} = h \times 0.433 \text{ psi} Δ P loss ​ = h × 0.433 psi

Vertical Drop (Going DOWN): Add 0.433 psi for every 1 foot of vertical drop ( h h h ): Δ P gain = h × 0.433 psi \Delta P_{\text{gain}} = h \times 0.433 \text{ psi} Δ P gain ​ = h × 0.433 psi +-------------------------------------------------------------------------+

  • | ELEVATION HEAD CONVERSION RULES |
  • +-------------------------------------------------------------------------+
  • | Elevation Rise (Pumping Upward) | SUBTRACT 0.433 psi per foot of rise |
  • | Elevation Drop (Flowing Downward)| ADD 0.433 psi per foot of drop |
  • | Pressure to Head Conversion | Multiply psi by 2.31 to get Feet |
  • | Head to Pressure Conversion | Multiply Feet by 0.433 to get psi |
  • +-------------------------------------------------------------------------+
  • Friction Head Loss in Water Service Piping & Meters

As water travels through pipes, fittings, and meters, viscous shear stresses between fluid layers and friction against the pipe wall dissipate energy. This energy dissipation is known as friction head loss .

1. Water Meter Friction Losses

Water utilities size meters using American Water Works Association (AWWA) standards (e.g., AWWA C700 for positive displacement meters). Water meters force water through a rotating disc or oscillating piston, creating a fixed pressure drop that increases exponentially with flow rate. At peak design flow rates, a standard residential 5 / 8 " × 3 / 4 " 5/8" \times 3/4" 5/8" × 3/4" meter incurs a pressure drop between 3.0 and 8.5 psi , while a 1-inch commercial meter can incur a loss of 5.0 to 12.0 psi .

2. Pipe Friction Loss & Equivalent Fitting Length

Piping friction is calculated using the Hazen-Williams hydraulic formula, which accounts for flow rate ( Q Q Q in gpm), internal pipe diameter ( d d d in inches), and pipe interior roughness ( C C C -factor, where smooth copper/PEX = 150, new steel = 120, and weathered galvanized pipe = 100).

Every directional change fitting creates localized turbulence. Plumbers convert fittings into an equivalent length of straight pipe added to the physical developed length:

Fitting Type 3/4-Inch Pipe Equivalent Length (ft) 1-Inch Pipe Equivalent Length (ft) 1-1/4-Inch Pipe Equivalent Length (ft)

  • 90 ∘ 90^\circ 9 0 ∘ Standard Elbow 2.0 2.5 3.5
  • 45 ∘ 45^\circ 4 5 ∘ Standard Elbow 1.0 1.4 1.8
  • Tee (Straight Run) 0.5 0.8 1.1
  • Tee (Through Branch) 4.0 5.0 6.5
  • Full-Port Ball Valve 0.4 0.5 0.7
  • Gate Valve 0.4 0.6 0.8
  • Swing Check Valve 6.0 8.0 11.0
  • Step-by-Step Pressure Calculation Example

Consider an installation scenario typical of the Indiana Journeyman examination:

Problem Scenario

A plumber is sizing the water service and main distribution riser for a two-story light commercial medical clinic.

Municipal Main Static Pressure: 72.0 psi 72.0 \text{ psi} 72.0 psi

Total Developed Length: 120 feet 120 \text{ feet} 120 feet of 1-inch Type K copper (physical run from street main to highest fixture)

Equivalent Fitting Allowance: 30 feet 30 \text{ feet} 30 feet of equivalent length for elbows, tees, and control valves

Total Equivalent Length: 120 + 30 = 150 feet 120 + 30 = 150 \text{ feet} 120 + 30 = 150 feet

Elevation Differential: The highest fixture (a commercial flushometer water closet on the second floor) is located 26 feet vertically above the street main tap.

  • Peak Design Flow Rate: 28 gpm 28 \text{ gpm} 28 gpm
  • Pressure Drop Through 1-Inch Water Meter at 28 gpm: 6.2 psi 6.2 \text{ psi} 6.2 psi

Friction Loss in 1-Inch Type K Copper at 28 gpm: 7.5 psi per 100 feet 7.5 \text{ psi per 100 feet} 7.5 psi per 100 feet

Step 1: Calculate Elevation Head Loss Δ P elevation = 26 ft × 0.433 psi/ft = 11.26 psi \Delta P_{\text{elevation}} = 26 \text{ ft} \times 0.433 \text{ psi/ft} = 11.26 \text{ psi} Δ P elevation ​ = 26 ft × 0.433 psi/ft = 11.26 psi

Step 2: Calculate Total Pipe Friction Loss Δ P friction = ( 150 ft total equivalent length 100 ft ) × 7.5 psi = 1.5 × 7.5 = 11.25 psi \Delta P_{\text{friction}} = \left(\frac{150 \text{ ft total equivalent length}}{100 \text{ ft}}\right) \times 7.5 \text{ psi} = 1.5 \times 7.5 = 11.25 \text{ psi} Δ P friction ​ = ( 100 ft 150 ft total equivalent length ​ ) × 7.5 psi = 1.5 × 7.5 = 11.25 psi

Step 3: Sum All Pressure Losses Δ P total loss = Δ P elevation + Δ P meter + Δ P friction \Delta P_{\text{total loss}} = \Delta P_{\text{elevation}} + \Delta P_{\text{meter}} + \Delta P_{\text{friction}} Δ P total loss ​ = Δ P elevation ​ + Δ P meter ​ + Δ P friction ​ Δ P total loss = 11.26 psi + 6.20 psi + 11.25 psi = 28.71 psi \Delta P_{\text{total loss}} = 11.26 \text{ psi} + 6.20 \text{ psi} + 11.25 \text{ psi} = 28.71 \text{ psi} Δ P total loss ​ = 11.26 psi + 6.20 psi + 11.25 psi = 28.71 psi

Step 4: Determine Residual Flow Pressure at Highest Fixture Residual Pressure = Static Street Pressure − Δ P total loss \text{Residual Pressure} = \text{Static Street Pressure} - \Delta P_{\text{total loss}} Residual Pressure = Static Street Pressure − Δ P total loss ​ Residual Pressure = 72.00 psi − 28.71 psi = 43.29 psi \text{Residual Pressure} = 72.00 \text{ psi} - 28.71 \text{ psi} = 43.29 \text{ psi} Residual Pressure = 72.00 psi − 28.71 psi = 43.29 psi

Step 5: Verify Compliance with IPC Table 604.3

Under IPC Table 604.3, a commercial siphon-jet flushometer water closet requires a minimum residual flow pressure of 25.0 psi . Available Residual Pressure ( 43.29 psi ) ≥ Required Minimum Pressure ( 25.0 psi ) \text{Available Residual Pressure } (43.29 \text{ psi}) \ge \text{Required Minimum Pressure } (25.0 \text{ psi}) Available Residual Pressure ( 43.29 psi ) ≥ Required Minimum Pressure ( 25.0 psi )

The design is fully compliant, providing an adequate safety margin of 43.29 − 25.0 = 18.29 psi 43.29 - 25.0 = 18.29 \text{ psi} 43.29 − 25.0 = 18.29 psi to handle future pipe aging and utility pressure fluctuations.