Study guide

14.1 Visual Descent Point (VDP) & Circling Approaches

FAA Instrument Rating - Airplane IRA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Instrument Rating Requirements

1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements

2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements

2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification

3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments

3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions

4 Chapter 4: Electronic Flight Displays, AHRS & Automation

4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management

5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations

5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures

6 Chapter 6: Aviation Meteorology & Atmospheric Hazards

6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear

7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts

7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products

8 Chapter 8: Ground-Based Navigation Systems

8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components

9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations

9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency

10 Chapter 10: IFR En Route Charts, Airspace & Altitudes

10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements

11 Chapter 11: ATC Clearances, Procedures & Lost Communications

11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations

12 Chapter 12: IFR Departures, Arrival Procedures & Holding

12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel

13 Chapter 13: Instrument Approach Procedures & Navigation Profiles

13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV

14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches

14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)

14.1 Visual Descent Point (VDP) & Circling Approaches

Key Takeaways Explain This Topic AI

A Visual Descent Point (VDP), identified by a bold 'V' on straight-in non-precision approach profile views, is the defined point from which a continuous stabilized 3° descent from the MDA to the runway touchdown point may begin.

VDP distance from the runway threshold is calculated as Distance (NM) = HAT / 300; timing from FAF to VDP is computed by subtracting HAT * 0.1 seconds from the total FAF-to-MAP time, with early descent below MDA strictly prohibited.

Circling approaches are published when the final approach course exceeds a 30° alignment offset with the runway centerline (15° for GPS) or when the final descent gradient exceeds 400 ft/NM.

Standard TERPS circling protected airspace radii are Cat A: 1.3 NM, Cat B: 1.5 NM, Cat C: 1.7 NM, Cat D: 2.3 NM; expanded TERPS (negative 'C' icon) increases these radii based on airport elevation while guaranteeing 300 ft of obstacle clearance.

If visual contact with the runway environment is lost during a circling maneuver, the pilot must execute an immediate missed approach climbing turn TOWARD the landing runway centerline before establishing on the published missed approach course.

Last updated: August 2026

Visual Descent Point (VDP) & Circling Approaches

Quick Answer: A Visual Descent Point (VDP) is a defined point on the final approach course of a non-precision straight-in approach from which a normal stabilized 3 ∘ 3^\circ 3 ∘ descent from the Minimum Descent Altitude (MDA) to the runway touchdown point may begin. Calculated as Distance (NM) = HAT ÷ 300 \text{Distance (NM)} = \text{HAT} \div 300 Distance (NM) = HAT ÷ 300 or Time to subtract from FAF-to-MAP = HAT × 0.1 seconds \text{Time to subtract from FAF-to-MAP} = \text{HAT} \times 0.1\text{ seconds} Time to subtract from FAF-to-MAP = HAT × 0.1 seconds , descending below MDA prior to the VDP is strictly prohibited. Circling approaches are required when the approach course is offset > 30 ∘ > 30^\circ > 3 0 ∘ from the runway centerline (or > 15 ∘ > 15^\circ > 1 5 ∘ for GPS) or the descent gradient exceeds 400 ft/NM 400\text{ ft/NM} 400 ft/NM . Standard TERPS protected radii are Cat A: 1.3 NM, Cat B: 1.5 NM, Cat C: 1.7 NM, Cat D: 2.3 NM, while expanded TERPS (indicated by a negative C icon) enlarges these areas at higher field elevations to ensure 300 ft 300\text{ ft} 300 ft of obstacle clearance. If visual contact is lost during circling, immediately execute a missed approach climbing turn toward the landing runway .

The final segment of a non-precision instrument approach presents significant energy management and obstacle clearance challenges. Unlike precision approaches (ILS or LPV) that provide continuous vertical electronic guidance directly to a decision point, non-precision approaches (LOC, VOR, RNAV LNAV) rely on stepdown altitudes and a flat Minimum Descent Altitude (MDA).

Without proper planning, pilots often fly a "dive-and-drive" technique—descending rapidly to the MDA and leveling off until arriving at the Missed Approach Point (MAP). If the pilot breaks out at the MAP, attempting to land requires an excessively steep, unstabilized dive toward the runway threshold. To prevent this hazard and provide a stabilized transition from instrument flight to landing, the FAA established the Visual Descent Point (VDP) and defined rigorous criteria for Circling Approaches .

The Visual Descent Point (VDP)

A Visual Descent Point (VDP) is a defined point on the final approach course of a non-precision straight-in approach procedure from which a normal descent from the MDA to the runway touchdown point may be commenced, provided the approach threshold of that runway, or approach lights, or other markings identifiable with the approach end of that runway are clearly visible to the pilot (AIM 5-4-5). +-----------------------------------------------------------------------------------------+

  • | VISUAL DESCENT POINT (VDP) PROFILE GEOMETRY |
  • | |
  • | Final Approach Fix (FAF) |
  • | ● |
  • | \ |
  • | \ Descent on Final |
  • | \ |
  • | ▼___________________ [ VDP ] |
  • | Minimum Descent Alt (MDA) \ |
  • | (Level Flight Segment) \ Stabilized 3° Descent |
  • | \ (HAT ÷ 300 ft/NM) |
  • | \ |
  • | \ Missed Approach |
  • | \ Point (MAP) |
  • | ▼ ● |
  • | ══════════════════════════════════════════════════════[===]═══════════╧════ |
  • | Threshold Touchdown Zone |
  • | |
  • | ◄─────────────────────── Distance = HAT ÷ 300 ────────► |
  • +-----------------------------------------------------------------------------------------+
  • Symbology and Publication

Chart Symbol: Represented on the profile view of FAA instrument approach charts by a bold uppercase "V" .

Fix Identification: A VDP is identified by DME distance, an along-track distance (ATD) RNAV waypoint, or a cross-radial fix.

Applicability: Published only on non-precision straight-in approaches. VDPs are never published on precision approaches (which have electronic glideslopes) or circling-only approaches.

Why Some Approaches Do Not Have a Published VDP

If a non-precision straight-in approach chart does not depict a "V" symbol, one of several conditions exists:

Obstacle Penetrations: An obstacle penetrates the visual descent surface ( 20 : 1 20:1 20 : 1 or 34 : 1 34:1 34 : 1 obstacle clearance surface) between the MDA and the runway threshold.

Lack of Fix Identification: There is no DME, marker beacon, or RNAV fix available to positively identify the VDP location along the final approach course.

TERPS Clearance Restrictions: Terrain or airspace constraints prevent establishing a standard 3 ∘ 3^\circ 3 ∘ descent profile from the MDA.

Warning

If an approach does not publish a VDP, pilots should exercise extreme caution when descending below the MDA. The absence of a published VDP often indicates that unseen obstacles penetrate the visual segment between the MDA and the runway threshold!

VDP Mathematical Formulas & Calculations

When a VDP is not charted or when flying non-precision approaches, instrument pilots can compute their own Visual Descent Point using two primary methods: +-----------------------------------------------------------------------------------------+

  • | VDP CALCULATION FORMULAS |
  • | |
  • | 1. Distance Method (Distance in NM from runway threshold): |
  • | |
  • | Height Above Touchdown (HAT) in feet |
  • | VDP Distance (NM) = ------------------------------------ |
  • | 300 |
  • | |
  • | 2. Timing Method (Seconds to subtract from total FAF-to-MAP elapsed time): |
  • | |
  • | Seconds to Subtract = HAT (feet) x 0.1 (or HAT ÷ 10) |
  • +-----------------------------------------------------------------------------------------+
  • 1. Distance Calculation: HAT ÷ 300 \text{HAT} \div 300 HAT ÷ 300

Standard 3 ∘ 3^\circ 3 ∘ descent path equals approximately 318 feet per nautical mile ( 6 , 076.1 ft × tan ⁡ ( 3 ∘ ) ≈ 318.4 ft/NM 6,076.1\text{ ft} \times \tan(3^\circ) \approx 318.4\text{ ft/NM} 6 , 076.1 ft × tan ( 3 ∘ ) ≈ 318.4 ft/NM ). The FAA rounds this to 300 ft/NM for simplified cockpit mental math.

Formula: Distance from Threshold (NM) = HAT (ft) 300 \text{Distance from Threshold (NM)} = \frac{\text{HAT (ft)}}{300} Distance from Threshold (NM) = 300 HAT (ft) ​

Worked Calculation Example 1:

  • Approach: LOC Rwy 28
  • MDA: 860 ft MSL 860\text{ ft MSL} 860 ft MSL
  • Touchdown Zone Elevation (TDZE): 260 ft MSL 260\text{ ft MSL} 260 ft MSL

Height Above Touchdown (HAT) = 860 − 260 = 600 ft \text{Height Above Touchdown (HAT)} = 860 - 260 = 600\text{ ft} Height Above Touchdown (HAT) = 860 − 260 = 600 ft VDP Distance = 600 ft 300 ft/NM = 2.0 NM from threshold \text{VDP Distance} = \frac{600\text{ ft}}{300\text{ ft/NM}} = \mathbf{2.0\text{ NM from threshold}} VDP Distance = 300 ft/NM 600 ft ​ = 2.0 NM from threshold

Interpretation: The pilot must establish visual contact and begin descending from 860 ft 860\text{ ft} 860 ft at 2.0 NM 2.0\text{ NM} 2.0 NM from the runway threshold. If the DME station is co-located with the threshold, the VDP is at 2.0 DME .

2. Time Calculation: HAT × 0.1 \text{HAT} \times 0.1 HAT × 0.1

When DME or GPS along-track distance is unavailable, the pilot calculates elapsed time from the Final Approach Fix (FAF) to the MAP and subtracts a time buffer.

Formula: Time to Subtract (seconds) = HAT × 0.1 = HAT 10 \text{Time to Subtract (seconds)} = \text{HAT} \times 0.1 = \frac{\text{HAT}}{10} Time to Subtract (seconds) = HAT × 0.1 = 10 HAT ​ VDP Clock Time = Total FAF-to-MAP Time − ( HAT × 0.1 ) \text{VDP Clock Time} = \text{Total FAF-to-MAP Time} - (\text{HAT} \times 0.1) VDP Clock Time = Total FAF-to-MAP Time − ( HAT × 0.1 )

Worked Calculation Example 2:

Approach: VOR Rwy 16 (FAF to MAP distance = 4.5 NM 4.5\text{ NM} 4.5 NM )

Groundspeed on final: 90 knots 90\text{ knots} 90 knots (FAF-to-MAP time from table = 3 min 00 sec = 180 seconds 3\text{ min } 00\text{ sec} = 180\text{ seconds} 3 min 00 sec = 180 seconds )

HAT = 450 ft \text{HAT} = 450\text{ ft} HAT = 450 ft Seconds to Subtract = 450 × 0.1 = 45 seconds \text{Seconds to Subtract} = 450 \times 0.1 = 45\text{ seconds} Seconds to Subtract = 450 × 0.1 = 45 seconds VDP Target Time = 180 s − 45 s = 135 seconds ( 2 min 15 sec after FAF ) \text{VDP Target Time} = 180\text{ s} - 45\text{ s} = 135\text{ seconds } (\mathbf{2\text{ min } 15\text{ sec}} \text{ after FAF}) VDP Target Time = 180 s − 45 s = 135 seconds ( 2 min 15 sec after FAF )

Interpretation: Start the timer when crossing the FAF. The VDP occurs at 2 minutes 15 seconds . If visual references are acquired by 2:15, initiate a 3 ∘ 3^\circ 3 ∘ descent; if not, maintain MDA until reaching the MAP at 3:00.

Operational Rules Governing the VDP +-----------------------------------------------------------------------------------------+

  • | VDP OPERATIONAL DECISION RULES |
  • | |
  • | Situation | Mandatory Pilot Action |
  • | -------------------------------------- | -------------------------------------------- |
  • | Visual reference acquired BEFORE VDP | Maintain MDA; DO NOT descend until VDP. |
  • | Visual reference acquired AT VDP | Initiate normal 3° descent to landing. |
  • | Visual reference NOT acquired at VDP | Continue level at MDA to MAP; do not descend! |
  • | Visual reference acquired AFTER VDP | Land ONLY if normal descent rate possible; |
  • | | otherwise execute missed approach at MAP. |
  • +-----------------------------------------------------------------------------------------+
  • 1. Prohibition on Early Descent Below MDA

Under 14 CFR § 91.175, an aircraft is strictly prohibited from descending below the MDA prior to reaching the VDP , even if the approach lights or runway environment are visible miles before the VDP.

Hazard: Descending early creates an abnormally flat, shallow descent profile. This dramatically increases the risk of Controlled Flight Into Terrain (CFIT) by penetrating obstacle clearance surfaces below the MDA.

2. Arrival at VDP Without Visual References

If the aircraft reaches the VDP without establishing the required visual references under § 91.175(c), the pilot MUST NOT descend below MDA .

However, reaching the VDP is NOT a missed approach trigger. The pilot is legally authorized to continue flying level at the MDA along the final approach course until reaching the Missed Approach Point (MAP).

3. Visual Acquisition After Passing VDP

If visual references are acquired between the VDP and the MAP, descending to land will require a descent angle steeper than 3 ∘ 3^\circ 3 ∘ (often exceeding 800 – 1000 FPM 800\text{--}1000\text{ FPM} 800 – 1000 FPM in light aircraft).

If a normal descent rate using normal maneuvers cannot be maintained to touch down within the touchdown zone, the pilot must not attempt a landing and must execute a missed approach at the MAP.

Circling Approaches: Purpose & Designation

A Circling Approach is the visual maneuvering phase of an instrument approach procedure used to align an aircraft with a landing runway when a straight-in landing from that instrument approach is not possible or desirable. +-----------------------------------------------------------------------------------------+

  • | WHEN IS AN APPROACH DESIGNATED CIRCLING-ONLY? |
  • | |
  • | An approach is designated with a letter suffix (e.g., VOR-A, RNAV-B) when: |
  • | |
  • | 1. Final Approach Course Offset: |
  • | • Exceeds 30° alignment with the runway centerline (exceeds 15° for GPS/RNAV). |
  • | |
  • | 2. Final Descent Gradient: |
  • | • Exceeds 400 ft/NM (approx. 3.77° / 6.6%) from the FAF to the threshold. |
  • | |
  • | 3. Unsurveyed Runway Environment: |
  • | • Runway lacks published markings, lighting, or surveyed touchdown zone data. |
  • +-----------------------------------------------------------------------------------------+
  • Naming Conventions for Circling-Only Approaches

When an approach procedure does not meet straight-in criteria, the runway number is omitted from the title and replaced with a sequential alphabetical suffix starting with the letter "A" (e.g., VOR-A , VOR/DME-B , RNAV (GPS)-A ).

Suffix letters are assigned sequentially for each distinct circling approach designed for an airport, regardless of the NAVAID type.

Aircraft Approach Categories (14 CFR § 97.3)

Instrument approach minimums and protected circling airspace boundaries are grouped into five distinct aircraft approach categories based on 1.3 × V S O 1.3 \times V_{SO} 1.3 × V SO ​ (stall speed in the landing configuration) at the maximum certified landing weight:

  • Category Certified Approach Speed ( 1.3 × V S O 1.3 \times V_{SO} 1.3 × V SO ​ ) Typical Aircraft Types
  • Cat A Less than 91 knots 91\text{ knots} 91 knots Cessna 172, Piper Archer, Beechcraft Bonanza

Cat B 91 knots 91\text{ knots} 91 knots to 120 knots 120\text{ knots} 120 knots Beechcraft King Air, Cessna Caravan, Piper Cheyenne

Cat C 121 knots 121\text{ knots} 121 knots to 140 knots 140\text{ knots} 140 knots Boeing 737, Airbus A320, Bombardier CRJ-700

Cat D 141 knots 141\text{ knots} 141 knots to 165 knots 165\text{ knots} 165 knots Boeing 777, Boeing 747, McDonnell Douglas MD-11

Cat E 166 knots 166\text{ knots} 166 knots or greater Specialized military aircraft only

Important

Speed Category Operational Rule: If a pilot flies an approach or circling maneuver at an indicated airspeed higher than the aircraft's certified category speed (e.g., flying a Cat A Cessna 182 at 105 KIAS 105\text{ KIAS} 105 KIAS on downwind), the pilot MUST use the higher category minimums (Cat B) . Operating at higher speeds increases turn radii and requires larger protected airspace!

Loading diagram... Visual Descent Point (VDP) Decision Tree & Approach Flow

TERPS Protected Circling Airspace Radii

Under United States Standard for Terminal Instrument Procedures (TERPS), procedure designers construct protected circling airspace by drawing circular arcs from the threshold of each usable runway and connecting the arcs with tangential lines. +-----------------------------------------------------------------------------------------+

  • | TERPS PROTECTED CIRCLING AIRSPACE ARCS |
  • | |
  • | ┌──────────────────────────────────────────────┐ |
  • | .─' '─. |
  • | .─' PROTECTED CIRCLING AIRSPACE '─. |
  • | .' '. |
  • | / Arc Radius (R) Arc Radius (R) \ |
  • | │ ◄──────────────► ◄──────────────► │ |
  • | │ ┌───●──────────────┐ ┌──────────────●───┐ │ |
  • | │ │ Runway 09 End │══════════│ Runway 27 End │ │ |
  • | │ └───●──────────────┘ └──────────────●───┘ │ |
  • | \ / |
  • | '. Guarantees 300 ft Minimum Obstacle Clearance .' |
  • | '─. (ROC) .─' |
  • | '─. .─' |
  • | └──────────────────────────────────────────────┘ |
  • +-----------------------------------------------------------------------------------------+
  • Minimum Obstacle Clearance

Within the entire protected circling area, TERPS guarantees a minimum of 300 feet of Required Obstacle Clearance (ROC) above the highest obstacle.

Standard TERPS Circling Radii (Legacy Criteria)

Historically, TERPS defined static circling radii based solely on approach category, calculated for sea level standard temperature and zero wind with a 15 ∘ 15^\circ 1 5 ∘ bank angle:

  • Category A: 1.3 NM 1.3\text{ NM} 1.3 NM
  • Category B: 1.5 NM 1.5\text{ NM} 1.5 NM
  • Category C: 1.7 NM 1.7\text{ NM} 1.7 NM
  • Category D: 2.3 NM 2.3\text{ NM} 2.3 NM
  • Category E: 4.5 NM 4.5\text{ NM} 4.5 NM
  • Expanded TERPS Circling Radii (The Negative "C" Icon C \mathbf{\mathcal{C}} C )

Why Expanded Criteria Were Introduced: At high-elevation airports, true airspeed (TAS) is substantially higher than indicated airspeed (IAS) for a given category. Higher TAS increases turn radius ( R = V 2 / ( g tan ⁡ θ ) R = V^2 / (g \tan\theta) R = V 2 / ( g tan θ ) ), causing faster category aircraft (such as Cat C and D jets) to fly outside legacy protected airspace boundaries.

The Icon: On approach charts designed under expanded criteria, a white "C" inside a black square (negative C: C \mathbf{\mathcal{C}} C ) is printed next to the circling line of minimums. +-----------------------------------------------------------------------------------------+

  • | EXPANDED TERPS CIRCLING RADII BY MDA ALTITUDE TIERS |
  • | |
  • | Approach Cat | 1,000 ft or less | 1,001–3,000 ft | 3,001–5,000 ft | 5,001–7,000 ft |
  • | ------------ | ---------------- | -------------- | -------------- | --------------- |
  • | Category A | 1.3 NM | 1.3 NM | 1.4 NM | 1.5 NM |
  • | Category B | 1.7 NM | 1.8 NM | 1.8 NM | 1.9 NM |
  • | Category C | 2.7 NM | 2.8 NM | 2.9 NM | 3.1 NM |
  • | Category D | 3.6 NM | 3.7 NM | 3.8 NM | 4.0 NM |
  • | Category E | 4.5 NM | 4.6 NM | 4.8 NM | 5.0 NM |
  • +-----------------------------------------------------------------------------------------+
  • Circling Maneuver Rules & Lost Visual Contact Procedures

When executing a circling maneuver in IMC conditions transitioning to visual: +-----------------------------------------------------------------------------------------+

  • | LOST VISUAL CONTACT DURING CIRCLING |
  • | |
  • | 1. LOST VISUAL CONTACT AT ANY POINT IN CIRCLING |
  • | │ |
  • | ▼ |
  • | 2. INITIATE IMMEDIATE MISSED APPROACH (FULL POWER & CLIMB) |
  • | │ |
  • | ▼ |
  • | 3. MAKE AN INITIAL CLIMBING TURN TOWARD LANDING RUNWAY |
  • | │ |
  • | ▼ |
  • | 4. FLY OVER AIRPORT & INTERCEPT PUBLISHED MISSED APPROACH TRACK |
  • +-----------------------------------------------------------------------------------------+

Step-by-Step Circling Rules:

Maintain MDA: The pilot must remain at or above the circling MDA until the aircraft is continuously in a position from which a descent to landing can be made on the intended runway at a normal rate of descent using normal maneuvers.

Visual Contact: The runway environment must remain in sight at all times.

Maneuvering Airspace: The entire visual circling pattern must be confined within the published protected circling radius.

The Lost Visual Contact Golden Rule

If visual reference with the runway environment is lost at any point during a circling maneuver (e.g., entering a low scud cloud or thick fog on downwind or base):

Immediately initiate a missed approach (apply full go-around power and pitch for climb).

Make an immediate climbing turn TOWARD the landing runway centerline .

Continue the climbing turn until established over the airport, then track outbound along the published missed approach course for the instrument approach procedure just flown.

Caution

Why Turn Toward the Landing Runway? Turning away from the airport or attempting to circle blindly outside the pattern guarantees flight into un-surveyed obstacles. Turning toward the landing runway ensures the aircraft remains directly over the surveyed, protected airport environment while gaining altitude, safely intercepting the missed approach corridor.