Study guide
11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations
FAA Instrument Rating - Airplane IRA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Instrument Rating Requirements
1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements
2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements
2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification
3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments
3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions
4 Chapter 4: Electronic Flight Displays, AHRS & Automation
4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management
5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations
5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures
6 Chapter 6: Aviation Meteorology & Atmospheric Hazards
6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear
7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts
7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products
8 Chapter 8: Ground-Based Navigation Systems
8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components
9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations
9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency
10 Chapter 10: IFR En Route Charts, Airspace & Altitudes
10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements
11 Chapter 11: ATC Clearances, Procedures & Lost Communications
11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations
12 Chapter 12: IFR Departures, Arrival Procedures & Holding
12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel
13 Chapter 13: Instrument Approach Procedures & Navigation Profiles
13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV
14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches
14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)
11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations
Key Takeaways Explain This Topic AI
Under 14 CFR 91.167(a), an airplane may not be operated in IFR conditions unless it carries enough fuel to fly to the first airport of intended landing, then to the alternate airport, and then for an additional 45 minutes at normal cruising speed (30 minutes for helicopters).
14 CFR 91.167(b) removes only the alternate-airport leg from the fuel calculation — never the 45-minute reserve — and it does so under the same weather test as the 1-2-3 rule: a published standard instrument approach at the destination plus a forecast ceiling of at least 2,000 feet above airport elevation and visibility of at least 3 statute miles from 1 hour before to 1 hour after the ETA.
14 CFR 91.169(c) sets standard alternate weather minimums of 600 feet and 2 statute miles for an airport with an operative precision approach and 800 feet and 2 statute miles for a non-precision approach, evaluated at the ETA at the alternate; non-standard minimums or an 'alternate NA' restriction are flagged on the approach chart.
Preferred IFR routes, Tower En Route Control (TEC) routes, and Coded Departure Routes (CDRs) are published in the Chart Supplement and on the FAA website; filing them dramatically reduces the chance of a full-route amendment at clearance delivery and is the practical answer to ACS route-planning knowledge.
The core IFR planning arithmetic is groundspeed equals true airspeed corrected for the wind component, time equals distance divided by groundspeed, fuel equals time multiplied by fuel flow, and estimated time of arrival is departure time plus estimated time en route expressed in UTC — with local-to-UTC conversion done by adding 4 hours for EDT, 5 for EST or CDT, 6 for CST or MDT, 7 for MST or PDT, and 8 for PST.
Last updated: September 2026
14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations
Quick Answer: Under 14 CFR § 91.167(a) , an IFR flight must carry fuel to (1) reach the first airport of intended landing, (2) fly from there to the alternate , and (3) fly 45 more minutes at normal cruising speed (30 minutes for helicopters). Paragraph (b) deletes only leg (2) — never the 45 minutes — and only when the destination has a published standard instrument approach and the forecast from 1 hour before to 1 hour after the ETA shows a ceiling at least 2,000 feet above airport elevation and visibility at least 3 statute miles . That is the same weather test as the 1-2-3 rule in § 91.169(b) . Standard alternate minimums under § 91.169(c) are 600-2 (precision) and 800-2 (non-precision). Route planning uses published preferred IFR routes , TEC routes , and CDRs ; the arithmetic is GS = TAS ± wind component , time = distance ÷ GS , fuel = time × fuel flow , and ETA = departure + ETE , expressed in UTC .
1. IFR Fuel Requirements: 14 CFR § 91.167
This is one of the most frequently missed regulation questions on the IRA knowledge test, because candidates confuse the fuel rule (§ 91.167) with the alternate-filing rule (§ 91.169). They share a weather test, but they are different regulations answering different questions. +-----------------------------------------------------------------------------+
- | 14 CFR 91.167(a) - IFR FUEL REQUIREMENT |
- | |
- | No person may operate a civil aircraft in IFR conditions unless it |
- | carries enough fuel (considering weather reports and forecasts and |
- | weather conditions) to: |
- | |
- | [1] Complete the flight to the FIRST AIRPORT OF INTENDED LANDING; |
- | + |
- | [2] Fly from that airport to the ALTERNATE AIRPORT; |
- | + |
- | [3] Fly after that for 45 MINUTES at normal cruising speed |
- | (30 minutes for helicopters). |
- +-----------------------------------------------------------------------------+
- The § 91.167(b) Exception — What It Actually Removes
Paragraph (b) states that item [2] — the alternate leg — does not apply when both of the following are true:
Part 97 prescribes a standard instrument approach procedure to the first airport of intended landing (or a special IAP has been issued to the operator for it); and
For at least 1 hour before through 1 hour after the estimated time of arrival , the appropriate weather reports or forecasts indicate a ceiling at least 2,000 feet above the airport elevation and visibility at least 3 statute miles .
Warning
The 45 minutes never goes away. Removing the alternate from the flight plan removes the alternate leg from the fuel calculation. It does not shorten or delete the 45-minute reserve, and it does not convert the flight into a VFR-reserve operation. The three-part structure of § 91.167(a) always applies to IFR flight; only item [2] can drop out.
Fuel Rule vs. Alternate Rule — Side by Side
14 CFR § 91.167 (Fuel) 14 CFR § 91.169 (Alternate)
Question answered How much fuel must be aboard? Must an alternate be listed on the flight plan?
- Trigger Any operation in IFR conditions Filing an IFR flight plan
- Weather test Standard IAP + 2,000 ft ceiling / 3 SM from ETA −1 hr to ETA +1 hr Identical (the 1-2-3 rule)
- Effect when the test is met Alternate leg is dropped from the fuel calculation No alternate need be filed
- What always remains 45 minutes at normal cruising speed Nothing — an alternate is either required or it is not
- Standard Alternate Minimums: § 91.169(c)
Once an alternate is required, the airport chosen must be forecast, at the ETA at that alternate , to meet:
- Alternate Airport Situation Required Forecast Minimums
- Operative precision approach available 600 feet ceiling and 2 statute miles visibility
- Operative non-precision approach available 800 feet ceiling and 2 statute miles visibility
- No instrument approach available Descent from the MEA, approach, and landing must be possible under basic VFR
These are the standard values. An approach chart carrying the inverted-triangle A symbol has non-standard alternate minimums published in the front of the Terminal Procedures Publication, and an "A NA" notation disallows alternate planning based on that procedure; another qualifying procedure may still permit use of the airport. A WAAS-equipped aircraft may plan an RNAV (GPS) approach at both destination and alternate, but must use LNAV or circling minima , not LPV minima, when checking alternate weather.
2. Preferred IFR Routes, TEC, and CDRs
ATC route amendments are the single most common source of a rushed, mis-copied clearance. The FAA publishes the routing it wants to see, and filing it is the cheapest workload reduction available to an instrument pilot.
Route Product What It Is Where to Find It
Preferred IFR Routes Published low-altitude and high-altitude routings between major terminals, designed to keep opposing traffic flows and departure/arrival streams separated Chart Supplement U.S. and the FAA's preferred-routes database
Tower En Route Control (TEC) Point-to-point IFR routing conducted entirely between adjacent approach control facilities, without entering an ARTCC's en route structure; typically for shorter flights at lower altitudes Chart Supplement U.S. (TEC route tables); request by filing the published route and adding "TEC"
Coded Departure Routes (CDRs) Eight-character coded reroutes pre-validated by ATC for weather and volume reroutes FAA CDR database; commonly issued to Part 121/135 operators but usable by any operator who has the code
National Playbook Pre-coordinated severe-weather reroute sets applied nationally during convective events FAA Air Traffic Control System Command Center
Planning rule: if a preferred route exists between your city pair, file it. Filing direct between two major terminals almost guarantees a full-route amendment read at high speed by a busy clearance delivery controller — exactly the situation in which altitude and transponder errors are made.
Route planning also requires cross-checking the same publications the ACS lists as route-planning inputs: available navigational facilities , special use airspace , preferred routes , primary and alternate airports , en route charts , the Chart Supplement , NOTAMs , and the Terminal Procedures Publication .
3. The Core Flight Planning Calculations
Groundspeed, Time, Distance, and Fuel Groundspeed (kt) = True Airspeed ± Wind Component \text{Groundspeed (kt)} = \text{True Airspeed} \pm \text{Wind Component} Groundspeed (kt) = True Airspeed ± Wind Component Time (hr) = Distance (NM) Groundspeed (kt) Fuel (gal) = Time (hr) × Fuel Flow (gph) \text{Time (hr)} = \frac{\text{Distance (NM)}}{\text{Groundspeed (kt)}} \qquad \text{Fuel (gal)} = \text{Time (hr)} \times \text{Fuel Flow (gph)} Time (hr) = Groundspeed (kt) Distance (NM) Fuel (gal) = Time (hr) × Fuel Flow (gph)
A useful cruise rule of thumb: true airspeed increases roughly 2% of indicated airspeed per 1,000 feet of altitude , so 120 KIAS at 8,000 feet is approximately 139 KTAS before temperature corrections.
Worked Example: A Complete § 91.167 Fuel Computation
- Planning Input Value
- Destination distance 180 NM
- Cruise true airspeed 120 kt
- Headwind component 15 kt
- Alternate, beyond the destination 45 NM
- Cruise fuel flow 9.5 gph
- Taxi, run-up, and climb allowance 1.5 gal
- Groundspeed: 120 − 15 = 105 kt 120 - 15 = \mathbf{105\text{ kt}} 120 − 15 = 105 kt
Time to destination: 180 ÷ 105 = 1.714 hr = 1 : 43 180 \div 105 = 1.714\text{ hr} = \mathbf{1{:}43} 180 ÷ 105 = 1.714 hr = 1 : 43
Time to alternate: 45 ÷ 105 = 0.429 hr = 0 : 26 45 \div 105 = 0.429\text{ hr} = \mathbf{0{:}26} 45 ÷ 105 = 0.429 hr = 0 : 26
Reserve: 0 : 45 \mathbf{0{:}45} 0 : 45 at normal cruising speed
Total required flying time: 1 : 43 + 0 : 26 + 0 : 45 = 2 : 54 1{:}43 + 0{:}26 + 0{:}45 = \mathbf{2{:}54} 1 : 43 + 0 : 26 + 0 : 45 = 2 : 54 (2.90 hours)
Fuel required: 2.90 × 9.5 = 27.6 gal 2.90 \times 9.5 = 27.6\text{ gal} 2.90 × 9.5 = 27.6 gal , plus 1.5 gal taxi/climb allowance = 29.1 gallons = \mathbf{29.1\text{ gallons}} = 29.1 gallons
If the destination met the § 91.167(b) test, step 3 would drop out and the requirement would fall to 1 : 43 + 0 : 45 = 2 : 28 1{:}43 + 0{:}45 = 2{:}28 1 : 43 + 0 : 45 = 2 : 28 (2.47 hours), or about 23.5 gallons plus the taxi allowance — but the 45 minutes stays.
Estimated Time of Arrival and UTC Conversion
Flight plans, clearances, and every weather product are expressed in Coordinated Universal Time (UTC / Zulu) . Convert by adding the offset for the local time zone:
- Local Time Zone Add to Get UTC Local Time Zone Add to Get UTC
- EDT (Eastern Daylight) +4 hours MDT (Mountain Daylight) +6 hours
- EST (Eastern Standard) +5 hours MST (Mountain Standard) +7 hours
- CDT (Central Daylight) +5 hours PDT (Pacific Daylight) +7 hours
- CST (Central Standard) +6 hours PST (Pacific Standard) +8 hours
Worked example: Departing at 1:15 p.m. CDT with an ETE of 1:43 . Departure in UTC is 1315 + 0500 = 1815 Z 1315 + 0500 = \mathbf{1815Z} 1315 + 0500 = 1815Z ; the ETA is 1815 + 0143 = 1958 Z 1815 + 0143 = \mathbf{1958Z} 1815 + 0143 = 1958Z . That ETA is the anchor for the § 91.167(b) and § 91.169(b) weather windows — evaluate the destination forecast from 1858Z to 2058Z .
Climb and Descent Planning
Climb rate required for a published gradient: FPM = ( Groundspeed 60 ) × Gradient (ft/NM) \text{FPM} = \left(\dfrac{\text{Groundspeed}}{60}\right) \times \text{Gradient (ft/NM)} FPM = ( 60 Groundspeed ) × Gradient (ft/NM)
Descent distance (3:1 rule): 3 NM for each 1,000 feet to lose
Descent rate on a 3° path: FPM = Groundspeed × 5 \text{FPM} = \text{Groundspeed} \times 5 FPM = Groundspeed × 5
Tip
Run the numbers against the worst case, not the flight plan. Compute the fuel requirement using the forecast headwind at your planned altitude , and recompute if ATC assigns a lower altitude, a reroute, or a hold. The regulation is written in terms of what the aircraft actually carries, not what the original plan assumed.