Study guide

11.4 14 CFR 91.185 Lost Communications Procedures

FAA Instrument Rating - Airplane IRA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Instrument Rating Requirements

1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements

2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements

2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification

3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments

3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions

4 Chapter 4: Electronic Flight Displays, AHRS & Automation

4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management

5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations

5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures

6 Chapter 6: Aviation Meteorology & Atmospheric Hazards

6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear

7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts

7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products

8 Chapter 8: Ground-Based Navigation Systems

8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components

9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations

9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency

10 Chapter 10: IFR En Route Charts, Airspace & Altitudes

10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements

11 Chapter 11: ATC Clearances, Procedures & Lost Communications

11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations

12 Chapter 12: IFR Departures, Arrival Procedures & Holding

12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel

13 Chapter 13: Instrument Approach Procedures & Navigation Profiles

13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV

14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches

14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)

11.4 14 CFR 91.185 Lost Communications Procedures

Key Takeaways Explain This Topic AI

Upon identifying two-way radio failure, the pilot must squawk Mode 3/A transponder code 7600 and troubleshoot avionics before applying 14 CFR § 91.185 procedures.

If two-way radio failure occurs in Visual Meteorological Conditions (VMC), or if VMC is encountered at any point, the pilot MUST continue the flight under VFR and land as soon as practical.

In Instrument Meteorological Conditions (IMC), the pilot must navigate the Route determined by the AVE-F hierarchy in strict order of precedence: Assigned, Vectored, Expected, or Filed.

In IMC, the pilot must fly the Altitude determined by the MEA rule: the HIGHEST of Minimum en route IFR altitude, Expected altitude, or Assigned altitude for the specific route segment being flown.

When reaching a clearance limit from which an approach begins: if an EFC time was received, commence descent and approach at the EFC time; if no EFC was received, commence descent and approach at the filed Estimated Time of Arrival (ETA).

Last updated: August 2026

14 CFR 91.185 Lost Communications Procedures

Quick Answer: Under 14 CFR § 91.185 , squawk 7600 . If in VMC , continue under VFR and land as soon as practical. If in IMC , fly the Route (AVE-F) in order of precedence: A ssigned, V ectored (direct to fix/route if lost during vector), E xpected, or F iled. Fly the Altitude (MEA) : the HIGHEST of M inimum IFR altitude, E xpected altitude, or A ssigned altitude for each segment. At a Clearance Limit that is an approach fix, begin approach at the EFC time (or at filed ETA if no EFC given).

A complete loss of two-way radio communications while operating under Instrument Flight Rules in IMC is an emergency situation that demands strict adherence to standardized regulatory procedures. Because Air Traffic Control separates other aircraft based on the assumption that the lost-comm aircraft will follow 14 CFR § 91.185 , any improvisation or deviation by the pilot creates immediate collision risks.

Immediate Troubleshooting & Transponder Actions

Before assuming complete receiver and transmitter failure, pilots should execute immediate troubleshooting: +-------------------------------------------------------------------------+

  • | LOST COMMS TROUBLESHOOTING CHECKLIST |
  • | |
  • | 1. Verify Frequency & Audio Panel Configuration: |
  • | • Check selected frequency against en route chart / approach plate |
  • | • Verify COM 1 / COM 2 mic selector switches and speaker/headset |
  • | • Check volume knobs and pull squelch test |
  • | • Verify headset jacks are securely plugged in |
  • | |
  • | 2. Re-establish Contact: |
  • | • Switch to previous ATC frequency or Flight Service (FSS) RCO |
  • | • Monitor guard / emergency frequency 121.500 MHz (or 243.0 UHF) |
  • | • Listen over operational VOR voice channels (HIWAS/TWEB legacy) |
  • | |
  • | 3. Set Transponder to Squawk 7600: |
  • | • SQUAWK 7600 immediately (alerts ATC radar automated trackers) |
  • | |
  • | 4. Transmit Blind: |
  • | • Transmit intentions in the blind: "Transmitting in the blind..." |
  • | • (Transmitter may still function even if receiver is dead) |
  • +-------------------------------------------------------------------------+
  • The Primary Decision Fork: VMC vs. IMC (14 CFR § 91.185(b))

The very first decision in a lost communications scenario depends entirely on the prevailing flight conditions: +-------------------------------------------------------------------------+

  • | VMC vs. IMC DECISION FRAMEWORK |
  • | |
  • | VISUAL METEOROLOGICAL CONDITIONS (VMC): |
  • | • If the failure occurs in VFR conditions, OR if VFR conditions |
  • | are encountered at ANY time during the flight: |
  • | • RULE: The pilot MUST continue the flight under VFR and land as |
  • | soon as practical. |
  • | • Do NOT fly into clouds or continue an extensive IFR route if VMC |
  • | landing is possible at a nearby suitable airport! |
  • | |
  • | INSTRUMENT METEOROLOGICAL CONDITIONS (IMC): |
  • | • If the failure occurs in IMC, or if weather prevents continuing |
  • | safely under VFR: |
  • | • RULE: The pilot MUST execute the codified ROUTE and ALTITUDE rules |
  • | prescribed in 14 CFR § 91.185(c). |
  • +-------------------------------------------------------------------------+

"Land as Soon as Practical" vs. "Land as Soon as Possible": "Practical" means using sound aeronautical judgment to land at a safe, suitable airport with appropriate runway length, services, and weather, rather than forcing an immediate off-field landing or landing at an unserviceable strip.

Route to Fly in IMC: The AVE-F Hierarchy

Under 14 CFR § 91.185(c)(1) , the pilot must navigate along a specific route selected in strict order of precedence (remembered by the acronym AVE-F ): +-------------------------------------------------------------------------+

  • | AVE-F ROUTE SELECTION PRECEDENCE |
  • | |
  • | Order Code Route Element Application & Priority |
  • | ----- ---- ----------------- ------------------------------------- |
  • | 1 A ASSIGNED Route assigned in last ATC clearance |
  • | received. |
  • | 2 V VECTORED If being radar vectored, proceed |
  • | DIRECT from point of radio failure to |
  • | the fix, route, or airway specified in |
  • | the vector clearance. |
  • | 3 E EXPECTED Route ATC advised may be expected in a |
  • | further clearance (EFC route). |
  • | 4 F FILED Route filed in the original/amended |
  • | flight plan. |
  • +-------------------------------------------------------------------------+
  • Critical Vector Rule (V in AVE-F)

If communications fail while being vectored off-course by ATC (e.g., "Fly heading 090 for radar vectors to V120" ), the pilot must not continue flying heading 090 indefinitely. The pilot must turn and fly direct to the fix, route, or airway specified in the vector instruction.

Altitude to Fly in IMC: The Highest of MEA Rule

Under 14 CFR § 91.185(c)(2) , for each route segment being flown, the pilot must maintain the HIGHEST of the following three altitudes: +-------------------------------------------------------------------------+

  • | HIGHEST OF M-E-A ALTITUDE MATRIX |
  • | |
  • | Letter Altitude Element Definition |
  • | ------ ---------------------- ------------------------------------ |
  • | M MINIMUM IFR Altitude Minimum En Route IFR Altitude (MEA, |
  • | MOCA, MRA, MIA) for the segment. |
  • | E EXPECTED Altitude Altitude ATC advised to expect in a |
  • | further clearance (at specified time). |
  • | A ASSIGNED Altitude Last altitude assigned by ATC. |
  • +-------------------------------------------------------------------------+
  • Segment-by-Segment Application

The "highest of MEA" calculation must be applied dynamically to each individual route segment as the flight progresses: Altitude

  • 10,000 ft | +-----------------+ (Assigned: 10,000)
  • | | MEA: 10,000 ft |
  • 8,000 ft | +----------------------------+ +-------------+
  • | | Assigned: 8,000 ft | | Assigned: |
  • 6,000 ft | | MEA: 5,000 ft | | 8,000 ft |
  • | | (Fly 8,000 ft) | | MEA: 4,000ft|
  • 4,000 ft | | | | (Fly 8,000) |
  • +-+----------------------------+-----------------+-------------+-->
  • Segment 1: V244 Segment 2: V244 Segment 3: V244
  • (Over Plains) (Over Ridge) (Over Valley)

Segment 1: Assigned = 8,000 ft, MEA = 5,000 ft. Fly 8,000 ft (Assigned is highest).

Segment 2: Assigned = 8,000 ft, MEA = 10,000 ft. Climb to 10,000 ft upon reaching the fix where MEA rises (MEA is highest).

Segment 3: Assigned = 8,000 ft, MEA = 4,000 ft. Descend back to 8,000 ft (Assigned is highest again).

Leaving the Clearance Limit (14 CFR § 91.185(c)(3))

What happens when an aircraft reaches its clearance limit without communications? Federal regulations divide this into two distinct scenarios depending on whether the clearance limit is an approach fix: +-------------------------------------------------------------------------+

  • | LEAVING THE CLEARANCE LIMIT MATRIX |
  • | |
  • | Clearance Limit Type EFC Received? Pilot Action |
  • | ------------------------- -------------- -------------------------- |
  • | Fix from which an YES Hold until EFC time. Begin |
  • | approach begins descent and approach as |
  • | (e.g., IAF or FAF) close as possible to EFC. |
  • | |
  • | Fix from which an NO Hold until filed ETA. Begin |
  • | approach begins descent and approach as |
  • | (e.g., IAF or FAF) close as possible to ETA. |
  • | |
  • | Fix from which an YES Leave fix at EFC time. |
  • | approach DOES NOT begin Proceed to approach fix, |
  • | (e.g., En route NAVAID) hold until ETA, then start. |
  • | |
  • | Fix from which an NO Upon arrival at fix, proceed|
  • | approach DOES NOT begin to approach fix, hold until |
  • | (e.g., En route NAVAID) ETA, then start approach. |

+-------------------------------------------------------------------------+ Scenario A: Clearance Limit IS an Initial Approach Fix (IAF)

  • (En Route) ----------> [ IAF (Clearance Limit) ]
  • │
  • ├─► If EFC received ───► Hold until EFC ─► Start Approach
  • │

└─► If NO EFC received ─► Hold until ETA ─► Start Approach Scenario B: Clearance Limit IS NOT an Initial Approach Fix

  • (En Route) ──► [ En Route NAVAID (Limit) ] ──► Proceed to IAF ──► Hold to ETA ──► Start Approach
  • │
  • ├─► If EFC: Leave NAVAID at EFC time
  • └─► If NO EFC: Leave NAVAID immediately upon arrival
  • Determining Estimated Time of Arrival (ETA)

Under 14 CFR § 91.185, the pilot's ETA is calculated from the filed Estimated Time En Route (ETE) amended by the actual departure time (plus any ATC-advised en route delays). If the aircraft arrives at the approach fix prior to this calculated ETA, the pilot must enter holding at the approach fix until reaching the ETA, then commence the descent and approach.

Loading diagram... 14 CFR § 91.185 Lost Communications Decision Tree