Study guide

3.3 Magnetic Compass Mechanics & Errors

FAA Instrument Rating - Airplane IRA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Instrument Rating Requirements

1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements

2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements

2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification

3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments

3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions

4 Chapter 4: Electronic Flight Displays, AHRS & Automation

4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management

5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations

5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures

6 Chapter 6: Aviation Meteorology & Atmospheric Hazards

6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear

7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts

7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products

8 Chapter 8: Ground-Based Navigation Systems

8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components

9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations

9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency

10 Chapter 10: IFR En Route Charts, Airspace & Altitudes

10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements

11 Chapter 11: ATC Clearances, Procedures & Lost Communications

11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations

12 Chapter 12: IFR Departures, Arrival Procedures & Holding

12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel

13 Chapter 13: Instrument Approach Procedures & Navigation Profiles

13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV

14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches

14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)

3.3 Magnetic Compass Mechanics & Errors

Key Takeaways Explain This Topic AI

The magnetic compass is a self-contained, completely autonomous direction-seeking instrument requiring no electrical or vacuum power, serving as the ultimate heading backup in IFR flight.

Variation is the angular difference between True North and Magnetic North (Isogonic lines; East is least / subtract, West is best / add: TVMDC).

Deviation is magnetic interference caused by localized ferrous metals and electrical equipment within the aircraft, corrected using the Compass Correction Card.

Magnetic Dip Acceleration Errors (ANDS: Accelerate North, Decelerate South) occur on East and West headings due to the inertia of the float's counterweight and the vertical component of Earth's magnetic field.

Magnetic Dip Turning Errors (NOSE: North Opposite, South Exceeds) require pilots to undershoot turns to North (by Latitude + 1/2 Bank Angle) and overshoot turns to South when navigating by magnetic compass alone.

Last updated: August 2026

Magnetic Compass Mechanics & Errors

The Magnetic Compass is the only self-contained, direct-reading direction-seeking instrument installed in standard aircraft panels. Because it requires neither vacuum pump suction nor electrical power, it serves as the ultimate heading backup during electrical or gyroscopic instrument failures in IMC. However, because the compass relies on the Earth's magnetic flux lines, it is subject to severe physical and magnetic dip errors whenever the aircraft accelerates, decelerates, or banks in a turn.

Mastering magnetic compass behavior and knowing how to calculate turning rollout points is mandatory for FAA Instrument Rating practical and knowledge exams.

1. Magnetic Compass Construction & Mechanics +-----------------------------------------------------------------------------+

  • | MAGNETIC COMPASS CONSTRUCTION |
  • | |
  • | +-----------------------------+ |
  • | | Sealed Compass Bowl | |
  • | | (Damping Kerosene Fluid) | |
  • | | | |
  • | | [ Jeweled Pivot Bearing] | |
  • | | | | |
  • | | +---------+---------+ | |
  • | | | Float & Magnets | | |
  • | | | (Counterweighted) | | |
  • | | +---------+---------+ | |
  • | | | | |
  • | | [ Azimuth Card Scale] | |
  • | +--------------+--------------+ |
  • | | (Glass Window & Lubber Line) |
  • | [ Compass Correction Card ] |
  • +-----------------------------------------------------------------------------+
  • Internal Components

Float Assembly: Two small magnetized bar magnets attached beneath a buoyant aluminum float, mounted on a hardened steel pivot resting inside an agate jeweled bearing cup. This design allows the float to rotate freely and tilt up to approximately 18 ∘ 18^\circ 1 8 ∘ .

Damping Fluid: The sealed bowl is filled with clear, acid-free mineral spirits or white kerosene. This fluid dampens high-frequency mechanical vibration, lubricates the jeweled pivot, and reduces wild swinging oscillations.

Lubber Line: A vertical reference line etched on the front glass face against which the compass card is read.

B-N / C-S Compensating Screws: Small adjustable magnetic rods located within the compass housing used by avionics technicians to calibrate and minimize magnetic deviation.

2. Magnetic Dip & Terrestrial Magnetism

The Earth acts as a giant dipole magnet whose magnetic poles do not coincide with its geographic poles:

Magnetic Flux Geometry: At the Earth's Magnetic Equator, magnetic lines of flux flow parallel to the Earth's surface ( 0 ∘ 0^\circ 0 ∘ magnetic dip angle ).

Polar Flux Tilt: As one travels north or south toward the magnetic poles, flux lines curve steeply downward into the Earth ( 90 ∘ 90^\circ 9 0 ∘ dip angle at the magnetic poles).

Northern Hemisphere Counterweight: To prevent the north-seeking end of the magnet from dipping downward toward the floor in the Northern Hemisphere, manufacturers attach a tiny counterweight to the south-seeking end of the float assembly. This mechanical imbalance, combined with the vertical component of Earth's magnetic field, creates acceleration and turning dip errors. +-----------------------------------------------------------------------------+

  • | EARTH'S MAGNETIC DIP FIELD |
  • | |
  • | [ NORTH MAGNETIC POLE ] <==== Flux lines plunge 90° straight down |
  • | ^ |
  • | | |
  • | [ MID-LATITUDES (USA) ] <==== Flux lines tilt down at ~50° to 70° angle |
  • | ^ (Generates severe dip errors: ANDS/NOSE) |
  • | | |
  • | [ MAGNETIC EQUATOR ] <==== Flux lines are 100% horizontal |
  • | (Zero magnetic dip errors) |
  • +-----------------------------------------------------------------------------+
  • 3. Variation & Deviation

Before analyzing dynamic dip errors, pilots must distinguish between static navigational compass errors: Variation and Deviation . +-----------------------------------------------------------------------------+

  • | THE TVMDC HEADING CONVERSION SEQUENCE |
  • | |
  • | [ TRUE COURSE / HEADING ] |
  • | | |
  • | +--- (+/- VARIATION) ["East is Least (-), West is Best (+)"] |
  • | v |
  • | [ MAGNETIC COURSE / HEADING ] |
  • | | |
  • | +--- (+/- DEVIATION) [From Compass Correction Card] |
  • | v |
  • | [ COMPASS HEADING ] |
  • +-----------------------------------------------------------------------------+
  • 1. Variation (Magnetic Declination)

Definition: The angular difference between True North (geographic North Pole) and Magnetic North (magnetic pole in Northern Canada/Arctic Ocean).

Isogonic Lines: Dashed magenta lines drawn across aeronautical sectional and IFR en route charts connecting points of equal magnetic variation (e.g., 7 ∘ W 7^\circ\text{W} 7 ∘ W or 12 ∘ E 12^\circ\text{E} 1 2 ∘ E ).

Agonic Line: The unique isogonic line where magnetic variation is 0 ∘ 0^\circ 0 ∘ (True North and Magnetic North are perfectly aligned). In North America, the agonic line runs roughly from Lake Michigan down through Georgia/Florida.

Calculation Rule: "East is Least (subtract), West is Best (add)."

Example: True Heading = 090 ∘ 090^\circ 09 0 ∘ , Variation = 6 ∘ W → Magnetic Heading = 090 ∘ + 6 ∘ = 096 ∘ 6^\circ\text{W} \rightarrow \text{Magnetic Heading} = 090^\circ + 6^\circ = 096^\circ 6 ∘ W → Magnetic Heading = 09 0 ∘ + 6 ∘ = 09 6 ∘ .

2. Deviation

Definition: Magnetic interference caused by localized electromagnetic fields, avionics circuits, radar, engine ignition, and ferrous metal airframe components inside the aircraft.

Compass Swing & Correction Card: A technician aligns the aircraft on a surveyed airport compass rose on the ground with engine and radios running, adjusting the internal compensating magnets to minimize error. Remaining errors are recorded on the Compass Correction Card mounted below the compass.

FOR (Heading) 000 ∘ 000^\circ 00 0 ∘ 030 ∘ 030^\circ 03 0 ∘ 060 ∘ 060^\circ 06 0 ∘ 090 ∘ 090^\circ 09 0 ∘ 120 ∘ 120^\circ 12 0 ∘ 150 ∘ 150^\circ 15 0 ∘ 180 ∘ 180^\circ 18 0 ∘ 210 ∘ 210^\circ 21 0 ∘ 240 ∘ 240^\circ 24 0 ∘ 270 ∘ 270^\circ 27 0 ∘ 300 ∘ 300^\circ 30 0 ∘ 330 ∘ 330^\circ 33 0 ∘

STEER 001 ∘ 001^\circ 00 1 ∘ 028 ∘ 028^\circ 02 8 ∘ 059 ∘ 059^\circ 05 9 ∘ 092 ∘ 092^\circ 09 2 ∘ 121 ∘ 121^\circ 12 1 ∘ 152 ∘ 152^\circ 15 2 ∘ 179 ∘ 179^\circ 17 9 ∘ 208 ∘ 208^\circ 20 8 ∘ 239 ∘ 239^\circ 23 9 ∘ 272 ∘ 272^\circ 27 2 ∘ 301 ∘ 301^\circ 30 1 ∘ 329 ∘ 329^\circ 32 9 ∘

4. Magnetic Dip Errors: Acceleration Errors (ANDS)

Acceleration errors occur exclusively when flying on East ( 090 ∘ 090^\circ 09 0 ∘ ) or West ( 270 ∘ 270^\circ 27 0 ∘ ) headings (or headings with an east/west component) in the Northern Hemisphere. +-----------------------------------------------------------------------------+

  • | ACCELERATION DIP ERROR: ANDS |
  • | |
  • | ON EAST OR WEST HEADINGS (Northern Hemisphere): |
  • | |
  • | [ ACCELERATE ] ---> Inertia holds south counterweight back |
  • | ---> Float tilts forward |
  • | ---> Vertical magnetic dip pulls north needle DOWN |
  • | ===> COMPASS ROTATES INDICATING FALSE TURN TO NORTH |
  • | |
  • | [ DECELERATE ] ---> Inertia throws south counterweight forward |
  • | ---> Float tilts aft |
  • | ---> Vertical magnetic dip pulls north needle |
  • | ===> COMPASS ROTATES INDICATING FALSE TURN TO SOUTH |
  • | |
  • | MEMORY RULE: ANDS = Accelerate North, Decelerate South |
  • +-----------------------------------------------------------------------------+
  • Why ANDS Occurs

When the aircraft accelerates on an east or west heading, inertia causes the heavier, counterweighted south end of the float to lag behind the pivot point.

This tilts the float assembly. As the float tilts, the vertical component of Earth's magnetic flux pulls the north-seeking end of the magnet downward, rotating the card.

Result: The compass card rotates to indicate a false turn toward the North .

When the aircraft decelerates, inertia throws the counterweighted south end forward, tilting the card aft → \rightarrow → vertical flux pulls the magnet downward → \rightarrow → compass indicates a false turn toward the South .

On Direct North or South Headings: Acceleration/deceleration causes the float to tilt along its magnetic axis, resulting in pitch oscillation but no rotational dip error .

5. Magnetic Dip Errors: Turning Errors (NOSE / UNOS)

Turning errors occur when turning from or through North or South headings in the Northern Hemisphere. +-----------------------------------------------------------------------------+

  • | TURNING DIP ERROR: NOSE / UNOS |
  • | |
  • | TURNING FROM A NORTH HEADING: |
  • | - Centrifugal force swings the float's center of gravity outward. |
  • | - The float tilts, allowing vertical magnetic flux to pull North needle. |
  • | - Compass initially turns in the OPPOSITE direction or LAGS behind. |
  • | ===> NORTH OPPOSITE (Undershoot North) |
  • | |
  • | TURNING FROM A SOUTH HEADING: |
  • | - Centrifugal force tilts float. |
  • | - Vertical flux pulls North needle in the direction of the turn. |
  • | - Compass immediately RACES AHEAD / LEADS the actual turn rate. |
  • | ===> SOUTH EXCEEDS (Overshoot South) |
  • +-----------------------------------------------------------------------------+
  • Calculating Compass Turning Rollout Points (Lead/Lag Rule)

When flying partial-panel (without a heading indicator or attitude indicator), pilots must execute compass turns using the timed standard rate turn or the Compass Lead/Lag Rollout Formula : Rollout Lead / Lag Degrees = Aircraft Latitude + 1 2 × Bank Angle \text{Rollout Lead / Lag Degrees} = \text{Aircraft Latitude} + \frac{1}{2} \times \text{Bank Angle} Rollout Lead / Lag Degrees = Aircraft Latitude + 2 1 ​ × Bank Angle +-----------------------------------------------------------------------------+

  • | COMPASS ROLLOUT CALCULATION WORKFLOW |
  • | |
  • | EXAMPLE: Aircraft at 30°N Latitude executing a turn with 15° Bank Angle: |
  • | Correction = 30° + (15° / 2) = 30° + 7.5° ≈ 38° |
  • | |
  • | [ 1. TURNING TO NORTH (e.g., 360°) ] |
  • | Compass LAGS -> Pilot must UNDERSHOOT (Roll out early). |
  • | - Left turn to 360°: Roll out when compass reads 038° (360° + 38°) |
  • | - Right turn to 360°: Roll out when compass reads 322° (360° - 38°) |
  • | |
  • | [ 2. TURNING TO SOUTH (e.g., 180°) ] |
  • | Compass LEADS -> Pilot must OVERSHOOT (Roll out late). |
  • | - Left turn to 180°: Roll out when compass reads 142° (180° - 38°) |
  • | - Right turn to 180°: Roll out when compass reads 218° (180° + 38°) |
  • | |
  • | [ 3. TURNING TO EAST (090°) OR WEST (270°) ] |
  • | Zero turning dip error -> Roll out directly at 090° or 270°. |
  • +-----------------------------------------------------------------------------+
  • Summary of Compass Memory Rules

ANDS: A ccelerate N orth, D ecelerate S outh (on East/West headings).

NOSE: N orth O pposite (initial reverse/lag), S outh E xceeds (leads ahead).

UNOS: U ndershoot N orth, O vershoot S outh.

Oscillation Error: Fluid turbulence and rough mechanical motion cause the compass card to oscillate erratically. Always average the swing of the compass card during smooth, unaccelerated straight-and-level flight.

Loading diagram... Magnetic Compass System Errors & Corrections