Study guide

3.1 Pitot-Static System Mechanics & Errors

FAA Instrument Rating - Airplane IRA

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Instrument Rating Requirements

1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements

2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements

2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification

3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments

3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions

4 Chapter 4: Electronic Flight Displays, AHRS & Automation

4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management

5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations

5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures

6 Chapter 6: Aviation Meteorology & Atmospheric Hazards

6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear

7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts

7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products

8 Chapter 8: Ground-Based Navigation Systems

8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components

9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations

9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency

10 Chapter 10: IFR En Route Charts, Airspace & Altitudes

10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements

11 Chapter 11: ATC Clearances, Procedures & Lost Communications

11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations

12 Chapter 12: IFR Departures, Arrival Procedures & Holding

12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel

13 Chapter 13: Instrument Approach Procedures & Navigation Profiles

13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV

14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches

14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)

3.1 Pitot-Static System Mechanics & Errors

Key Takeaways Explain This Topic AI

The pitot-static system supplies total ram air pressure to the airspeed indicator (ASI) and ambient static pressure to the ASI, altimeter, and vertical speed indicator (VSI).

The airspeed indicator is the sole instrument connected to both pitot and static sources, measuring dynamic pressure (total ram pressure minus ambient static pressure).

If the pitot tube ram air opening is blocked while the drain hole remains open, ram pressure bleeds out and the ASI drops to 0 knots; if both ram and drain holes are blocked, the ASI acts like an altimeter (reads high in climb, low in descent).

A blocked static port freezes the altimeter at the altitude where the blockage occurred, causes the VSI to bleed down to 0 FPM, and causes the ASI to under-indicate airspeed during climbs and over-indicate during descents.

Under 14 CFR 91.411, the static pressure system, altimeter, and automatic altitude reporting system must be tested and inspected within the preceding 24 calendar months for IFR flight, and the altimeter must agree within ±75 feet of surveyed field elevation during preflight checks.

Last updated: August 2026

Pitot-Static System Mechanics & Errors

In Instrument Meteorological Conditions (IMC), flight by reference to flight instruments requires absolute confidence in and understanding of the pitot-static system . The pitot-static system is an interconnected pneumatic network that captures ambient air pressures outside the aircraft and channels them to three primary flight instruments: the Airspeed Indicator (ASI) , the Altimeter , and the Vertical Speed Indicator (VSI) .

A mechanical or environmental failure within this plumbing network—such as structural ice accretion, insects, or trapped moisture—can produce deceptive and contradictory cockpit indications. Because spatial disorientation and loss of control remain leading factors in fatal instrument flight accidents, instrument pilots must master the mechanical principles, pressure differentials, and failure signatures of the pitot-static system.

1. Pitot-Static System Architecture & Pressure Types

The pitot-static system relies on two fundamental fluid pressures governed by Bernoulli's Principle:

Static Pressure ( P static P_{\text{static}} P static ​ or p 0 p_0 p 0 ​ ): The ambient atmospheric pressure exerted equally on all surfaces of the aircraft, regardless of airspeed or direction of travel. As altitude increases, ambient static pressure decreases at a standard lapse rate of approximately 1.00 in Hg 1.00\text{ in Hg} 1.00 in Hg per 1 , 000 feet 1,000\text{ feet} 1 , 000 feet in the lower atmosphere ( 34 hPa / 1 , 000 ft 34\text{ hPa} / 1,000\text{ ft} 34 hPa /1 , 000 ft ).

Total Pressure / Ram Air Pressure ( P total P_{\text{total}} P total ​ or P pitot P_{\text{pitot}} P pitot ​ ): The stagnation pressure captured by an open-ended tube facing directly into the relative wind. Total pressure is the sum of ambient static pressure and dynamic pressure ( q q q ) created by aircraft motion through the air mass: P total = P static + q = P static + 1 2 ρ V 2 P_{\text{total}} = P_{\text{static}} + q = P_{\text{static}} + \frac{1}{2}\rho V^2 P total ​ = P static ​ + q = P static ​ + 2 1 ​ ρ V 2 (where ρ \rho ρ is air density and V V V is true airspeed). +-----------------------------------------------------------------------------+

  • | PITOT-STATIC SYSTEM PLUMBING ARCHITECTURE |
  • | |
  • | [ PITOT TUBE ] =========================> [ AIRSPEED INDICATOR (ASI) ] |
  • | (Ram Air + Drain) (Total / Ram Pressure) ^ |
  • | | |
  • | | (Static Pressure) |
  • | [ STATIC PORT ] ================================+ |
  • | (Flush-mounted) (Ambient Static Line) | |
  • | +=====> [ ALTIMETER ] |
  • | | |
  • | +=====> [ VSI ] |
  • +-----------------------------------------------------------------------------+
  • Plumbing & Hardware Components

Pitot Tube / Pitot Mast: Mounted externally on the wing leading edge, nose section, or vertical fin, aligned parallel with the aircraft's longitudinal axis outside the propeller slipstream and wing boundary layer. It features a forward-facing ram air inlet hole and a rear/bottom moisture drain hole . Most IFR-certified aircraft incorporate an internal electric heating element to prevent ice accumulation.

Static Port(s): Flush-mounted orifices installed on the side of the fuselage in an area of undisturbed airflow. Modern aircraft typically feature dual static ports (one on each side of the fuselage) connected via a Y-junction. This dual arrangement automatically cancels out aerodynamic pressure variations caused by yaw, slips, skids, or crosswind gusts.

Static Line Sump Drains: Low points in the pneumatic lines equipped with drain plugs to collect and drain condensation during maintenance inspections.

2. Airspeed Indicator (ASI) Mechanics & Airspeed Types

The Airspeed Indicator (ASI) is the only flight instrument connected to both the pitot pressure line and the static pressure line. +-----------------------------------------------------------------------------+

  • | AIRSPEED INDICATOR INTERNAL MECHANISM |
  • | |
  • | +-----------------------+ |
  • | | Sealed Outer Case | |
  • | | (Vented to STATIC) | |
  • | | | |
  • | [PITOT RAM AIR] ===> | +---------------+ | |
  • | | | Expandable | =====> [Mechanical Linkage] |
  • | | | Diaphragm | | | |
  • | | +---------------+ | v |
  • | +-----------------------+ [ASI Needle Dial] |
  • | ^ |
  • | [STATIC LINE] ===================+ |
  • +-----------------------------------------------------------------------------+
  • Internal Operating Principle

The ASI consists of an airtight outer case vented directly to the static line .

Inside the case sits a thin, corrugated bronze or beryllium copper expandable diaphragm connected directly to the pitot line .

When the aircraft is stationary on the ramp, static pressure inside the case equals total pressure inside the diaphragm → \rightarrow → diaphragm is relaxed → \rightarrow → needle reads zero.

In flight, dynamic pressure expands the diaphragm. Mechanical rocking shafts, levers, pinions, and hairsprings convert this physical expansion into needle rotation across the calibrated dial.

The Four Types of Airspeed

Airspeed Classification Definition & Governing Factors Practical / IFR Application

Indicated Airspeed (IAS) Uncorrected speed read directly from the cockpit gauge. Used for aircraft operating limitations ( V A , V F E , V N O , V N E V_A, V_{FE}, V_{NO}, V_{NE} V A ​ , V FE ​ , V NO ​ , V NE ​ ) and takeoff/landing speeds.

Calibrated Airspeed (CAS) IAS corrected for instrument installation and position errors (angle of attack airflow deflection). Published in the POH/AFM. At high angles of attack (slow flight), IAS may differ substantially from CAS.

Equivalent Airspeed (EAS) CAS corrected for adiabatic compressible airflow across the airframe. Critical for high-speed aircraft ( > 200 KIAS >200\text{ KIAS} > 200 KIAS or above Mach 0.4); negligible in light general aviation.

True Airspeed (TAS) CAS/EAS corrected for non-standard atmospheric pressure and temperature (density altitude). Actual velocity of the aircraft relative to the surrounding air mass. Rule of thumb: T A S ≈ I A S + ( 2 % × Altitude in Thousands of Feet ) TAS \approx IAS + (2\% \times \text{Altitude in Thousands of Feet}) T A S ≈ I A S + ( 2% × Altitude in Thousands of Feet ) .

Groundspeed (GS) TAS corrected for headwind, tailwind, or crosswind components. Actual speed across the Earth's surface; used for dead reckoning, ETA, fuel burn, and GPS ground track. +-----------------------------------------------------------------------------+

  • | AIRSPEED DEFINITION PROGRESSION |
  • | |
  • | [ IAS ] ---(+/- Position & Instrument Error)---> [ CAS ] |
  • | [ CAS ] ---(+/- Compressibility Error)---------> [ EAS ] |
  • | [ EAS ] ---(+/- Non-Standard Density Error)----> [ TAS ] |
  • | [ TAS ] ---(+/- Wind Vector Component)---------> [ GS ] |
  • +-----------------------------------------------------------------------------+
  • Airspeed Indicator Dial Markings (14 CFR 23 / 25)

White Arc (Flap Operating Range): Extends from V S O V_{SO} V SO ​ (stalling speed in landing configuration, flaps down) to V F E V_{FE} V FE ​ (maximum flap extended speed).

Green Arc (Normal Operating Range): Extends from V S 1 V_{S1} V S 1 ​ (stalling speed clean, gear/flaps up) to V N O V_{NO} V NO ​ (maximum structural cruising speed).

Yellow Arc (Caution Range): Extends from V N O V_{NO} V NO ​ to V N E V_{NE} V NE ​ . Flight in this range is permitted only in smooth, non-turbulent air.

Red Radial Line ( V N E V_{NE} V NE ​ ): Never Exceed Speed. Exceeding V N E V_{NE} V NE ​ risks catastrophic aeroelastic flutter and structural failure.

Unmarked Key Speeds: V A V_A V A ​ (Design Maneuvering Speed—decreases as aircraft weight decreases), V X V_X V X ​ (Best Angle of Climb), V Y V_Y V Y ​ (Best Rate of Climb), V L E V_{LE} V L E ​ (Maximum Landing Gear Extended Speed), and V L O V_{LO} V L O ​ (Maximum Landing Gear Operating Speed).

3. Sensitive Altimeter Mechanics & Errors

The Altimeter measures static atmospheric pressure to display the aircraft's height above a designated pressure datum. It is connected only to the static line. +-----------------------------------------------------------------------------+

  • | ALTIMETER INTERNAL MECHANISM |
  • | |
  • | [STATIC LINE] ===> [ Sealed Instrument Case (Vented to Static) ] |
  • | | |
  • | v (Compresses / Expands) |
  • | [ Aneroid Wafers ] (Evacuated / 29.92" Hg inside) |
  • | | |
  • | v |
  • | [ Mechanical Levers / Pinions ] |
  • | | |
  • | +---> [ 100-ft Pointer ] |
  • | +---> [ 1,000-ft Pointer ] |
  • | +---> [ 10,000-ft Pointer ] |
  • | |
  • | [ Barometric Setting Knob ] ===> Adjusts Kollsman Window & Pointers |
  • +-----------------------------------------------------------------------------+
  • Internal Operating Principle

Inside the airtight case is a stack of hollow, sealed aneroid wafers made of beryllium copper or phosphor bronze.

The inside of the wafers is evacuated to an absolute pressure of 29.92 in Hg 29.92\text{ in Hg} 29.92 in Hg ( 1013.2 hPa / mb 1013.2\text{ hPa} / \text{mb} 1013.2 hPa / mb ).

Climb: Ambient static pressure inside the case decreases → \rightarrow → trapped internal wafer pressure expands the wafers → \rightarrow → linkages rotate pointers clockwise to show higher altitude.

Descent: Ambient static pressure inside the case increases → \rightarrow → wafers compress → \rightarrow → pointers rotate counterclockwise.

The Kollsman Window (Barometric Scale)

Atmospheric pressure constantly fluctuates due to meteorological systems. The Kollsman window allows the pilot to set the local barometric altimeter setting (in inches of mercury or millibars/hectopascals).

Turning the adjustment knob shifts both the internal barometric scale and the altitude pointers.

A barometric adjustment of 1.00 in Hg 1.00\text{ in Hg} 1.00 in Hg changes the indicated altitude by exactly 1 , 000 feet 1,000\text{ feet} 1 , 000 feet ( 0.10 in Hg = 100 ft 0.10\text{ in Hg} = 100\text{ ft} 0.10 in Hg = 100 ft , 0.01 in Hg = 10 ft 0.01\text{ in Hg} = 10\text{ ft} 0.01 in Hg = 10 ft ).

IFR Requirement (14 CFR 91.121): When operating below 18 , 000 ft MSL 18,000\text{ ft MSL} 18 , 000 ft MSL , the altimeter must be set to the current reported altimeter setting of a station along the route within 100 NM 100\text{ NM} 100 NM . At or above 18 , 000 ft MSL 18,000\text{ ft MSL} 18 , 000 ft MSL (Flight Levels), all aircraft set 29.92 in Hg 29.92\text{ in Hg} 29.92 in Hg .

Ramp Check Limit: Prior to IFR flight, set the current local altimeter setting. The altimeter must indicate within ± 75 feet \pm 75\text{ feet} ± 75 feet of the surveyed airport/ramp elevation.

Types of Altitude

Indicated Altitude: Altitude read directly from the instrument with the current local altimeter setting in the Kollsman window.

Pressure Altitude: Altitude read when the Kollsman window is dialed to standard 29.92 in Hg 29.92\text{ in Hg} 29.92 in Hg . Used for computing aircraft performance and mandatory above 18 , 000 ft MSL 18,000\text{ ft MSL} 18 , 000 ft MSL .

Density Altitude: Pressure altitude corrected for non-standard temperature ( D A = P A + [ 120 × ( O A T − I S A temp ) ] DA = PA + [120 \times (OAT - ISA_{\text{temp}})] D A = P A + [ 120 × ( O A T − I S A temp ​ )] ). Directly dictates engine power, propeller efficiency, and wing lift.

True Altitude: The actual vertical distance of the aircraft above Mean Sea Level (MSL). Navigational charts, MEAs, obstacle elevations, and airport elevations are expressed in True Altitude.

Absolute Altitude: The vertical distance above the ground/terrain (AGL), measured directly by radar altimeters.

Non-Standard Pressure & Temperature Errors +-----------------------------------------------------------------------------+

  • | TEMPERATURE & PRESSURE ALTIMETER RULES |
  • | |
  • | "HIGH TO LOW, LOOK OUT BELOW" |
  • | - Flying from HIGH pressure/temperature into LOW pressure/temperature |
  • | - Altimeter reads HIGHER than actual true altitude |
  • | - Aircraft is LOWER than the pilot thinks (CFIT Hazard!) |
  • | |
  • | "LOW TO HIGH, CLEAR BLUE SKY" |
  • | - Flying from LOW pressure/temperature into HIGH pressure/temperature |
  • | - Altimeter reads LOWER than actual true altitude |
  • | - Aircraft is HIGHER than the pilot thinks |
  • +-----------------------------------------------------------------------------+

Warning

Cold Temperature Altimeter Hazard: In extremely cold air masses, the true altitude of the aircraft is significantly lower than the indicated altitude. In cold weather operations, pilots must apply cold temperature altitude corrections to published approach fix altitudes (AIM 7-3-1) to avoid Controlled Flight Into Terrain (CFIT).

4. Vertical Speed Indicator (VSI) Mechanics & Lag

The Vertical Speed Indicator (VSI) (or Rate-of-Climb Indicator) measures the rate of change of static pressure, displaying the aircraft's rate of climb or descent in feet per minute (FPM). It is connected only to the static line. +-----------------------------------------------------------------------------+

  • | VERTICAL SPEED INDICATOR (VSI) |
  • | |
  • | +-----------------------+ |
  • | | Sealed Outer Case | |
  • | | (Calibrated Leak) | |
  • | | ^ | |
  • | [STATIC LINE] =====> | | (Slow) | |
  • | | | +---------------+ | |
  • | +-----------> | | Expandable | =====> [Mechanical Linkage] |
  • | (Direct/ | | Diaphragm | | | |
  • | Instant) | +---------------+ | v |
  • | +-----------------------+ [VSI Rate Needle] |
  • +-----------------------------------------------------------------------------+
  • Internal Operating Principle: The Calibrated Leak

The VSI contains an expandable diaphragm inside an airtight case.

Static pressure is fed directly and unrestricted into the inside of the diaphragm.

Static pressure is fed into the outer case through a calibrated leak (a precision-engineered capillary tube or metering orifice).

Level Flight: Pressure inside the diaphragm matches pressure inside the case → \rightarrow → zero differential → \rightarrow → pointer rests at 0 FPM 0\text{ FPM} 0 FPM .

Initiating a Climb: Ambient pressure drops. Static pressure inside the diaphragm drops immediately. However, the calibrated leak restricts air from escaping the case quickly, so case pressure remains higher than diaphragm pressure → \rightarrow → higher case pressure compresses the diaphragm → \rightarrow → needle deflects upward to indicate a climb.

Stabilized Climb: Once the climb rate stabilizes, the calibrated leak allows case pressure to bleed out at a rate proportional to the climb, maintaining a constant differential corresponding to the rate of climb.

Level-Off: When leveling off, diaphragm pressure stabilizes instantly, while case pressure takes 6 to 9 seconds to equalize through the calibrated leak.

Overcoming VSI Lag: The Instantaneous VSI (IVSI)

Traditional mechanical VSIs have an inherent 6 to 9 second lag before indicating a stabilized rate. An Instantaneous Vertical Speed Indicator (IVSI) incorporates an internal accelerometer with spring-loaded dashpots (air pistons). During pitch changes, inertia moves the pistons to instantly create the required pressure differential, eliminating lag and providing immediate rate response.

5. Pitot-Static System Blockages & Failure Diagnostics

Recognizing pitot-static system blockages in IMC is a critical IFR survival skill. System blockages produce distinct diagnostic signatures across the three instruments: +-----------------------------------------------------------------------------+

  • | PITOT-STATIC SYSTEM FAILURE MATRIX |
  • | |
  • | FAILURE SCENARIO ASI ALTIMETER VSI |
  • | ----------------------------------------------------------------------- |
  • | Pitot Ram Blocked, Drops to 0 Normal Normal |
  • | Drain OPEN (Pressure bleeds out) |
  • | |
  • | Both Pitot Ram & Drain Acts as Altimeter: Normal Normal |
  • | BLOCKED (Trapped Ram) - Reads HIGH in climb |
  • | - Reads LOW in descent |
  • | |
  • | Static Port BLOCKED, - Reads LOW in climb Freezes at Bleeds |
  • | Pitot CLEAR - Reads HIGH in desc. blocked alt. to 0 FPM |
  • +-----------------------------------------------------------------------------+
  • Detailed Analysis of Failure Scenarios
  • Scenario A: Pitot Ram Air Hole Blocked, Drain Hole OPEN

Cause: Front of pitot tube collects bugs, dirt, or icing, while drain hole remains clear.

Mechanism: Ram air stops entering the pitot tube. Trapped air pressure inside the pitot tube escapes out the open drain hole into ambient air. Pressure inside the ASI diaphragm drops to ambient static pressure.

Instrument Manifestations:

ASI: Drops to zero knots (no differential between diaphragm and case).

Altimeter: Functions normally.

VSI: Functions normally.

Scenario B: Both Pitot Ram Air Hole AND Drain Hole BLOCKED

Cause: Complete icing of the pitot head (e.g., freezing rain or structural supercooled cloud droplets).

Mechanism: A slug of air pressure ( P trapped P_{\text{trapped}} P trapped ​ ) is sealed inside the pitot line and ASI diaphragm. The ASI case continues to receive changing static pressure from the unobstructed static port.

Instrument Manifestations:

In Level Flight at Constant Altitude: ASI freezes at the airspeed where the blockage occurred (even if power is changed or aircraft decelerates).

In a Climb: Ambient static pressure in the case decreases while trapped pitot diaphragm pressure remains constant. The pressure differential increases → \rightarrow → ASI indicates a FALSE INCREASE in airspeed (reads dangerously high) .

In a Descent: Ambient static pressure in the case increases while trapped pitot pressure remains constant. The pressure differential decreases → \rightarrow → ASI indicates a FALSE DECREASE in airspeed (reads low) .

Memory Rule: PUCD ( Pitot blocked: Climb = reads Up/fast, Descent = reads Down/slow ).

Caution

The Deadly Pitot Icing Trap: If both pitot holes freeze during a climb in IMC, the ASI will indicate increasing airspeed. An unsuspecting pilot may pitch up and pull back power to prevent an overspeed, inadvertently stalling the aircraft. Always cross-check attitude indicator pitch and engine power instruments (tachometer / manifold pressure).

Scenario C: Static Port BLOCKED, Pitot Tube CLEAR

Cause: Ice accretion over static ports, washing wax, or unremoved static port covers.

Mechanism: Static line traps the ambient pressure existing at the moment of blockage ( P trapped-static P_{\text{trapped-static}} P trapped-static ​ ). This trapped pressure affects all three instruments.

Instrument Manifestations:

Altimeter: Freezes completely at the altitude where the blockage occurred.

VSI: Case and diaphragm equalize at the trapped static pressure through the calibrated leak → \rightarrow → pointer returns to and remains frozen at 0 FPM , regardless of climb or descent.

ASI: Traps constant static pressure inside the ASI case.

During Climb: Dynamic pressure decreases as true static pressure drops, but the ASI case holds higher trapped static pressure → \rightarrow → pressure differential shrinks → \rightarrow → ASI under-indicates (reads lower than actual) .

During Descent: True ambient static increases, but the ASI case holds lower trapped static pressure → \rightarrow → pressure differential expands → \rightarrow → ASI over-indicates (reads higher than actual) .

Memory Rule: SDUC ( Static blocked: Descent = reads Up/fast, Climb = reads Down/slow ).

Loading diagram... Pitot-Static System Failure Diagnostic Tree