Study guide
8.4 Instrument Landing System (ILS) Ground Components
FAA Instrument Rating - Airplane IRA
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Instrument Rating Requirements
1.1 About the FAA Instrument Rating Knowledge Test 1.2 Aeronautical Experience & Certification Requirements 1.3 Instrument Recency & Currency Requirements
2 Chapter 2: IFR Preflight & Aircraft Equipment Requirements
2.1 14 CFR 91.205 Required IFR Instruments & Equipment 2.2 Inoperative Equipment, MELs & 14 CFR 91.213 2.3 Required Aircraft Inspections & Maintenance Records 2.4 VOR Equipment Accuracy Checks (14 CFR 91.171) 2.5 The Instrument Flight Deck Check & Flight Control Verification
3 Chapter 3: Pitot-Static, Gyroscopic & Magnetic Flight Instruments
3.1 Pitot-Static System Mechanics & Errors 3.2 Gyroscopic Instruments & Principles 3.3 Magnetic Compass Mechanics & Errors 3.4 Alternate Static Source & Instrument Malfunctions
4 Chapter 4: Electronic Flight Displays, AHRS & Automation
4.1 Electronic Flight Displays (PFD/MFD) & System Architecture 4.2 AHRS, ADC & Magnetometer Operation 4.3 Autopilot, Flight Director & Automation Management
5 Chapter 5: Attitude Instrument Flying & Partial-Panel Operations
5.1 Concept of Attitude Instrument Flying & Scanning Techniques 5.2 Pitch, Bank & Power Instrument Interpretation 5.3 Unusual Attitude Recoveries 5.4 Partial-Panel Instrument Flight & Systems Failures
6 Chapter 6: Aviation Meteorology & Atmospheric Hazards
6.1 Atmospheric Fundamentals, Pressure & Stability 6.2 Air Masses, Fronts & Frontal Weather 6.3 Structural & Induction Icing 6.4 Thunderstorms, Turbulence & Low-Level Wind Shear
7 Chapter 7: Aviation Weather Reports, Forecasts & Analysis Charts
7.1 Aviation Routine Weather Reports (METAR) & SPECI 7.2 Terminal Aerodrome Forecasts (TAF) & Aviation Forecasts 7.3 In-Flight Weather Advisories: AIRMETs, SIGMETs & PIREPs 7.4 Aviation Weather Charts & Graphic Products
8 Chapter 8: Ground-Based Navigation Systems
8.1 VOR Navigation Principles & Service Volumes 8.2 VOR Intercepting, Tracking & Radial Orientation 8.3 Distance Measuring Equipment (DME) Principles 8.4 Instrument Landing System (ILS) Ground Components
9 Chapter 9: Space-Based Navigation, GPS & RNAV Operations
9.1 Global Positioning System (GPS) Architecture & RAIM 9.2 Wide Area Augmentation System (WAAS) & SBAS 9.3 Area Navigation (RNAV) & Required Navigation Performance (RNP) 9.4 IFR Flight with GPS & Database Currency
10 Chapter 10: IFR En Route Charts, Airspace & Altitudes
10.1 IFR Low Altitude En Route Charts & Symbology 10.2 IFR Altitudes: MEA, MOCA, MAA, MRA, MCA & OROCA 10.3 Airspace Classification & IFR Operating Rules 10.4 IFR Cruising Altitudes & Oxygen Requirements
11 Chapter 11: ATC Clearances, Procedures & Lost Communications
11.1 IFR Flight Plan Filing & Activation 11.2 CRAFT Clearances & Departure Instructions 11.3 Mandatory IFR Position Reports & ATC Communications 11.4 14 CFR 91.185 Lost Communications Procedures 11.5 14 CFR 91.167 Fuel Requirements, Preferred Routes & Flight Planning Calculations
12 Chapter 12: IFR Departures, Arrival Procedures & Holding
12.1 Obstacle Departure Procedures (ODP) & Standard Instrument Departures (SID) 12.2 Standard Terminal Arrival Routes (STAR) 12.3 Holding Pattern Geometry, Speeds & Wind Drift Correction 12.4 Holding Pattern Entry Procedures: Direct, Teardrop & Parallel
13 Chapter 13: Instrument Approach Procedures & Navigation Profiles
13.1 Instrument Approach Plate Anatomy & Briefing 13.2 Precision Approaches: ILS Categories & Profiles 13.3 Non-Precision Approaches: VOR, LOC, RNAV (LNAV/LP) 13.4 APV Approaches: LPV, LNAV/VNAV & Baro-VNAV
14 Chapter 14: Approach Minimums, Landing Criteria & Missed Approaches
14.1 Visual Descent Point (VDP) & Circling Approaches 14.2 14 CFR 91.175 Landing Minimums & Visual References 14.3 Missed Approach Procedures & Rejected Landings 14.4 Engine-Inoperative Instrument Flight & Approaches (AMEL/AMES)
8.4 Instrument Landing System (ILS) Ground Components
Key Takeaways Explain This Topic AI
The Instrument Landing System (ILS) comprises four integrated sub-elements: Localizer (lateral guidance), Glide Slope (vertical guidance), Marker Beacons / DME (range fixes), and Approach Lighting Systems (visual transition).
The localizer operates on VHF frequencies from 108.10 to 111.95 MHz (odd tenths) and is 4 times more sensitive than a VOR, featuring a full-scale deflection of 2.5° (0.5° per dot) and producing a 700-foot course width at the threshold.
The glide slope operates on paired UHF frequencies (329.15 to 335.00 MHz) with a standard 3.0° descent angle and a narrow 1.4° total beam width; pilots must capture from below to avoid false harmonic glide slopes (e.g., 6° or 9°).
Marker beacons broadcast directional 75 MHz cones: Outer Marker (OM, blue light, 400 Hz low dashes at FAF/GS intercept 4–7 NM out), Middle Marker (MM, amber light, 1300 Hz dot-dash at Cat I DA ~200 ft AGL), and Inner Marker (IM, white light, 3000 Hz dots at Cat II DH ~100 ft AGL).
Under 14 CFR 91.175, pilots may descend below DA/MDA to 100 ft above TDZE using the approach lighting system, but cannot descend below 100 ft without red terminating bars (ALSF-1) or red side row bars (ALSF-2) in sight, or the runway threshold/touchdown zone.
Last updated: August 2026
Instrument Landing System (ILS) Ground Components
Quick Answer: The Instrument Landing System (ILS) is a precision approach system consisting of four sub-elements: (1) Localizer (LOC) operating on 108.10–111.95 MHz (odd tenths) providing lateral guidance with a 3° to 6° beam width ( 4× more sensitive than VOR , full deflection = 2.5 ° = 2.5° = 2.5° , 0.5 ° 0.5° 0.5° per dot); (2) Glide Slope (GS) operating on paired UHF channels ( 329.15–335.00 MHz ) providing a 3.0° descent path ( 1.4 ° 1.4° 1.4° total width); (3) Marker Beacons / DME on 75 MHz for range fixes (Outer Marker = Blue/400 Hz dashes at FAF; Middle Marker = Amber/1300 Hz dot-dashes at Cat I DA; Inner Marker = White/3000 Hz dots at Cat II DH); and (4) Approach Lighting Systems (ALS) enabling visual transition. Under 14 CFR 91.175 , descending below 100 ft above TDZE requires the red terminating bars (ALSF-1) or red side row bars (ALSF-2) in sight, or the runway threshold/touchdown zone.
The Instrument Landing System (ILS) is the premier terrestrial precision approach system in worldwide aviation. By combining VHF lateral guidance, UHF vertical guidance, range markers, and approach lighting, the ILS allows aircraft to conduct stabilized instrument descents to decision altitudes as low as 200 feet above ground level (Cat I) or to the surface (Cat IIIc).
ILS Architecture: The Four Core Subsystems +-------------------------------------------------------------------------+
- | ILS SYSTEM ARCHITECTURE |
- | |
- | 1. LATERAL GUIDANCE: VHF Localizer (LOC) |
- | - 108.10 to 111.95 MHz (odd tenths) |
- | - Aligned with runway centerline |
- | |
- | 2. VERTICAL GUIDANCE: UHF Glide Slope (GS) |
- | - 329.15 to 335.00 MHz (automatically |
- | paired with localizer VHF channel) |
- | - Standard 3.0° descent profile |
- | |
- | 3. RANGE / DISTANCE: Marker Beacons (75 MHz) or DME |
- | - Outer Marker (OM) / FAF |
- | - Middle Marker (MM) / Cat I DA |
- | - Inner Marker (IM) / Cat II DH |
- | |
- | 4. VISUAL TRANSITION: Approach Lighting System (ALS) |
- | - ALSF-1/2, MALSR, SSALR, PAPI/VASI |
- +-------------------------------------------------------------------------+
- 1. The Localizer (LOC): Lateral Guidance
The localizer antenna array is situated approximately 1,000 feet beyond the far departure end of the instrument runway. It transmits two overlapping directional radio lobes modulated at different audio frequencies: [ LOCALIZER RADIATION PATTERN ]
- Runaway Centerline
- ^
- 90 Hz Amplitude Lobe | 150 Hz Amplitude Lobe
- (Predominates on Left) | (Predominates on Right)
- \ | /
- \ DDM = 0 /
- \ (On Course)/
- \ | /
- \ | /
- ===============================[ LOC ANTENNA ]==============================
- (Departure End)
- Signal Modulation & DDM Principle
Left of Course (Fly-Right indication): The receiver detects a stronger 90 Hz modulation signal.
Right of Course (Fly-Left indication): The receiver detects a stronger 150 Hz modulation signal.
On Course Centerline: The Difference in Depth of Modulation (DDM) is zero ( 90 Hz = 150 Hz 90\text{ Hz} = 150\text{ Hz} 90 Hz = 150 Hz ), causing the vertical needle to center perfectly.
Localizer Beam Width & Sensitivity
Linear Width at Threshold: The beam is calibrated to produce a linear course width of 700 feet at the runway threshold.
Angular Width: Tailored based on runway length to between 3° and 6° (nominally 5° total width , or 2.5° on each side of center).
Sensitivity Comparison: A standard VOR has a full-scale deflection of 10° (2° per dot). A localizer has a full-scale deflection of 2.5° (0.5° per dot) —making the localizer four times more sensitive than a VOR .
- Localizer Standard Service Volume (SSV) LOCALIZER SERVICE VOLUME
- 35° 35°
- \ /
- \ /
- 10 NM \ / 10 NM
- +\------/+
- 10°\ / 10°
- \ /
- 18 NM \/
- |
- [ RUNWAY ]
± 35 ° \pm 35° ± 35° azimuth: Usable out to 10 NM from the antenna.
± 10 ° \pm 10° ± 10° azimuth: Usable out to 18 NM from the antenna.
Vertical coverage: From 1,000 ft above highest obstacle / terrain up to 4,500 ft AGL .
Localizer Back Course & Reverse Sensing
The localizer transmitter radiates energy out the back end of the antenna array down the reciprocal runway heading, creating a Back Course (LOC BC) . On a conventional CDI:
Flying the Front Course Inbound → \rightarrow → Standard sensing ("fly toward the needle").
Flying the Back Course Inbound → \rightarrow → Reverse sensing (needle moves opposite to correction).
Rule for conventional CDI on Back Course: To correct, fly away from the needle, OR set the front course on an HSI to receive normal sensing.
2. The Glide Slope (GS): Vertical Guidance
The glide slope antenna is located approximately 750 to 1,250 feet down the runway from the approach threshold and offset 250 to 650 feet from the runway centerline. It transmits overlapping 90 Hz and 150 Hz radiation patterns vertically: [ GLIDE SLOPE BEAM GEOMETRY ]
- / Upper Lobe (90 Hz)
- / Fly DOWN
- 3.7° /
- ----------------------+ (0.7° Above Path)
- / 3.0° Standard Angle /
- /----------------------+ On Glide Path (DDM = 0)
- / 2.3° /
- /----------------------+ (0.7° Below Path)
- / \ Lower Lobe (150 Hz)
- / \ Fly UP
- ===[ GS ANTENNA ]====================================================
- Technical Parameters of the Glide Slope
Frequency Band: UHF band ( 329.15 MHz to 335.00 MHz , 40 paired channels).
Standard Glide Path Angle: 3.0° above the horizontal plane.
Beam Width: 1.4° total ( 0.7 ° 0.7° 0.7° above and 0.7 ° 0.7° 0.7° below the 3.0° glide path).
Full Scale Vertical Deflection: Only 0.7° ( 0.14 ° 0.14° 0.14° per dot on a 5-dot vertical scale).
Service Volume: Usable out to 10 NM from the transmitter down to the runway threshold.
Standard Rate of Descent Calculations
To maintain a 3.0° glide slope, the required rate of descent in feet per minute (fpm) is calculated from groundspeed: Rate of Descent (fpm) ≈ Groundspeed (kts) × 5 \text{Rate of Descent (fpm)} \approx \text{Groundspeed (kts)} \times 5 Rate of Descent (fpm) ≈ Groundspeed (kts) × 5 Exact Rate of Descent (fpm) = Groundspeed (kts) × 101.3 × tan ( 3.0 ° ) ≈ GS × 5.3 \text{Exact Rate of Descent (fpm)} = \text{Groundspeed (kts)} \times 101.3 \times \tan(3.0°) \approx \text{GS} \times 5.3 Exact Rate of Descent (fpm) = Groundspeed (kts) × 101.3 × tan ( 3.0° ) ≈ GS × 5.3
- Groundspeed (kts) Rule of Thumb (fpm) Exact 3.0° Descent Rate (fpm)
- 90 kts 450 fpm 477 fpm
- 100 kts 500 fpm 530 fpm
- 120 kts 600 fpm 636 fpm
- 140 kts 700 fpm 742 fpm
- 160 kts 800 fpm 848 fpm
- False Glide Slopes & Capture Geometry
Ground reflections create harmonic lobes above the true glide path at multiples of the standard angle—most notably at approximately 6° and 9° : +-------------------------------------------------------------------------+
- | FALSE GLIDE SLOPE CHARACTERISTICS |
- | |
- | - Located at higher angles (e.g., 6.0° and 9.0° above horizontal). |
- | - Exhibit REVERSED SENSING (90 Hz lower, 150 Hz upper). |
- | - Require an abnormally steep, dangerous descent rate (> 1,200 fpm). |
- | |
- | DEFENSIVE PROCEDURE: |
- | - ALWAYS intercept the glide slope from BELOW at the published |
- | Glide Slope Intercept Altitude (indicated by the lightning bolt |
- | symbol on the FAA approach chart). |
- | - Verify altimeter cross-check at the Outer Marker / FAF. |
- +-------------------------------------------------------------------------+
- 3. Marker Beacons, Compass Locators & DME Fixes
Marker beacons operate on a single universal carrier frequency of 75.00 MHz , projecting an elliptical cone of radio energy vertically upward through the approach path.
Marker Beacon Typical Location Audio Tone & Morse Modulation Cockpit Light Associated Fix / Purpose
Outer Marker (OM) 4 to 7 NM from runway threshold 400 Hz low-pitch tone; Continuous dashes ( - - - ) at 2/sec BLUE Final Approach Fix (FAF); Glide Slope Intercept Altitude check
Middle Marker (MM) ~3,500 ft from threshold (~0.6 NM) 1300 Hz intermediate tone; Alternating dot-dash ( . - . - ) AMBER Category I Decision Altitude (DA); ~200 ft above TDZE
Inner Marker (IM) Between MM and threshold 3000 Hz high-pitch tone; Continuous dots ( . . . . ) at 6/sec WHITE Category II Decision Height (DH); ~100 ft above TDZE Outer Marker (OM) Middle Marker (MM) Inner Marker (IM)
- [ BLUE ] [ AMBER ] [ WHITE ]
- 400 Hz 1300 Hz 3000 Hz
- ( - - - ) ( . - . - ) ( . . . . )
- | | |
- | | |
- 4 to 7 NM ~3,500 ft ~1,000 ft [ RUNWAY ]
- Compass Locators & DME Substitution
Compass Locators: Low-power Non-Directional Beacons (NDBs) co-located with marker beacons. An NDB at the Outer Marker is a LOM (Locator Outer Marker) and transmits the first two letters of the localizer ID; an NDB at the Middle Marker is a LMM (Locator Middle Marker) and transmits the last two letters.
DME / Collocated Systems: Where authorized by the approach plate, DME fixes or IFR-approved GPS waypoints may substitute for the Outer Marker.
4. Approach Lighting Systems (ALS) & 14 CFR 91.175
Approach Lighting Systems provide the critical visual transition from cockpit instrument scan to external runway environment recognition during the final seconds of an instrument approach. +-------------------------------------------------------------------------+
- | COMMON APPROACH LIGHT CONFIGURATIONS |
- | |
- | - ALSF-1 / ALSF-2: High Intensity Approach Light System with |
- | Sequenced Flashers (ALSF-2 features RED side row bars). |
- | - SSALR / SSALF: Simplified Short Approach Light System with Runway |
- | Alignment Indicator Lights / Sequenced Flashers. |
- | - MALSR / MALSF: Medium Intensity Approach Light System with Runway |
- | Alignment Indicator Lights. |
- | - ODALS: Omni-Directional Approach Lighting System. |
- | - REIL: Runway End Identifier Lights (synchronized flashing strobes). |
- | - PAPI / VASI: Precision Approach Path / Visual Approach Slope Ind. |
- +-------------------------------------------------------------------------+
- Visual Descent Rules (14 CFR § 91.175)
To descend below the published Decision Altitude (DA) or Minimum Descent Altitude (MDA), three conditions must be met simultaneously:
The aircraft is continuously in a position from which a descent to a landing on the intended runway can be made at a normal rate of descent using normal maneuvers.
The flight visibility is not less than the visibility prescribed in the standard instrument approach procedure being used.
At least one of the following visual references for the intended runway is distinctly visible and identifiable to the pilot:
The approach light system (allows descent to 100 feet above Touchdown Zone Elevation (TDZE) , but NOT below 100 ft unless the red terminating bars (ALSF-1) or red side row bars (ALSF-2) are distinctly visible).
The threshold, threshold markings, or threshold lights.
The runway end identifier lights (REIL).
The visual glideslope indicator (VASI / PAPI).
The touchdown zone or touchdown zone markings / lights.
The runway or runway markings / lights.