Study guide

6.4 Hazardous Substances, Asbestos & LEV

IOSH Managing Safely Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 What Is IOSH Managing Safely? 1.2 Exam Format & Dual Assessment 1.3 Certificate Validity & Study Plan

2 Chapter 1: Introducing Managing Safely

2.1 Moral, Legal & Financial Reasons 2.2 The Accident Cost Iceberg 2.3 Responsibility & Accountability

3 Chapter 2: Assessing Risks

3.1 Hazard, Hazardous Event & Risk 3.2 Five Steps of Risk Assessment 3.3 The 5×5 Likelihood × Consequence Matrix 3.4 Residual Risk, Suitable & Sufficient, Review

4 Chapter 3: Controlling Risks

4.1 ERICPD Hierarchy of Control 4.2 Reasonably Practicable 4.3 Safe Systems of Work (SSoW) 4.4 Permits to Work

5 Chapter 4: Understanding Responsibilities

5.1 Criminal vs Civil Law 5.2 Employer & Employee Duties 5.3 Enforcement, Improvement & Prohibition Notices 5.4 Knowledge Tests & Management Systems (HSG65 / ISO 45001)

6 Chapter 5: Hazard Categories, Noise, Vibration & Substances

6.1 Six Hazard Categories 6.2 Noise Hazards & Action Values 6.3 Hand-Arm & Whole-Body Vibration 6.4 Hazardous Substances, Asbestos & LEV

7 Chapter 6: Work at Height, Manual Handling, Fire & Electricity

7.1 Work at Height 7.2 Manual Handling, Slips & Trips 7.3 Fire Safety Basics 7.4 Electricity Hazards

8 Chapter 7: Stress, Work Equipment & Other Hazards

8.1 Work-Related Stress & Psychosocial Hazards 8.2 Work Equipment & Machinery 8.3 Confined Spaces, Workplace Transport & Welfare

9 Chapter 8: Investigating Incidents

9.1 Accidents, Incidents & Near Misses 9.2 Immediate, Underlying & Root Causes 9.3 Four-Step Investigation Process 9.4 RIDDOR Reporting Overview

10 Chapter 9: Measuring Performance

10.1 Active (Proactive) vs Reactive Indicators 10.2 KPIs & Characteristics of Good Metrics 10.3 Auditing the Safety Management System 10.4 Calculating Injury Incidence & Frequency Rates 10.5 Inspections & Benchmarking

11 Chapter 10: Protecting the Environment

11.1 Environmental Basics: Pollution, Waste & Duty of Care 11.2 Reducing Environmental Impact & Environmental Management Systems

12 Chapter 11: Risk Assessment Project & Exam Day

12.1 Project Requirements & Marking 12.2 Worked Example: Four-Hazard Assessment 12.3 Written Assessment Strategy & High-Yield Review

6.4 Hazardous Substances, Asbestos & LEV

Key Takeaways Explain This Topic AI

Main routes of entry for hazardous substances are inhalation (usually primary at work), absorption through skin/eyes, ingestion, and injection (including sharps and high-pressure).

COSHH thinking for managers: assess risk, prevent or control exposure, monitor where needed, health surveillance where appropriate, plan for emergencies, and inform/train workers.

Asbestos remains in many older buildings; disturbance releases fibres — never DIY disturb suspect materials; use survey information and licensed or appropriately trained non-licensed work as required.

Local Exhaust Ventilation (LEV) captures contaminants at source; systems need correct design, use, and thorough examination and testing on a suitable regime.

Labels, safety data sheets (SDS), and storage segregation are basic everyday controls every manager should enforce.

Last updated: August 2026

6.4 Hazardous Substances, Asbestos & LEV

Quick Answer: Hazardous substances harm via inhalation, skin/eye absorption, ingestion, and injection . Manage them with COSHH logic — assess, prevent/control, monitor, health surveillance, emergencies, and training. Treat asbestos in older buildings as a high-stakes disturbance risk (never DIY). Use LEV to capture contaminants at source and keep it examined and tested. Read labels and SDS ; segregate incompatible storage.

Chemical and substance hazards sit in the chemical category of the six-category model, but they appear everywhere: cleaning cupboards, workshops, construction refurbishment, laboratories, kitchens, farms, and offices with printer toners and adhesives. Managing Safely does not turn you into an occupational hygienist, but it does expect you to manage substances like any other significant risk — with structured assessment and reliable controls, not guesswork.

Routes of entry

Harm depends on how a substance gets into or onto the body:

Route How it happens Workplace examples Control directions

Inhalation (primary for many workplace ill-health cases) Breathing dusts, fumes, gases, vapours, mists, fibres Welding fume, solvent vapour, wood dust, silica, asbestos fibres Enclose process; LEV; suppress dust; RPE as residual control; limit time

Absorption through skin / eyes Contact with liquids, mists, contaminated surfaces Solvents causing dermatitis; corrosives; some pesticides Eliminate contact; gloves/suitable PPE; splash protection; hygiene; eye wash

Ingestion Hand-to-mouth; contaminated food/drink; poor hygiene Eating in a dirty workshop; not washing before meals No food in process areas; washing facilities; clean/dirty zones

Injection Sharps, high-pressure puncture, animal bites Needles, high-pressure grease or paint injection injuries Safe sharps systems; guards; training; first-aid awareness of injection injuries

Exam emphasis: inhalation is usually the primary occupational route for chronic disease (asthma, cancer, COPD-type disease, asbestosis/mesothelioma risk pathways). Skin disease (dermatitis) is extremely common and often under-reported. Always think about the route when choosing controls — a mask does nothing for a skin sensitiser if gloves are wrong or missing.

COSHH idea — what managers must drive

In Great Britain, the Control of Substances Hazardous to Health Regulations (COSHH) set the main framework for most hazardous substances (with separate specialist regimes for things like asbestos and lead). Managing Safely teaches the managerial idea of COSHH rather than every technical schedule:

Assess the risk from substances used or generated (including process dusts and fumes, not only purchased chemicals).

Prevent exposure where reasonably practicable (eliminate the substance or process; substitute a safer alternative).

Control exposure adequately when prevention is not possible (priority: engineering and systems of work; PPE last).

Maintain, examine, and test control measures (especially LEV).

Monitor exposure where needed to show controls work.

Provide health surveillance where appropriate (for example asthmagens, sensitisers, chrome, some solvents — as indicated by assessment and OH advice).

Plan for accidents, incidents, and emergencies (spills, first aid, evacuation).

Ensure information, instruction, and training so people understand labels, SDS, and safe methods.

Prevention and control in practice

  • Prefer Example
  • Eliminate Stop using a solvent-based adhesive; change design so coating is unnecessary
  • Substitute Water-based paint instead of high-VOC solvent paint
  • Enclose Fully enclosed mixing vessel
  • LEV / engineering Capturing hood on a soldering station; booth for spraying
  • Systems of work Weigh powders carefully; wet cutting to suppress silica dust
  • PPE / RPE Correct gloves and fitted respirators after higher controls

Adequate control means reducing exposure to a level that prevents ill health, taking account of any workplace exposure limits (WELs) where they apply. Managers escalate when people report symptoms, when visible dust or strong odours are routine, or when LEV is damaged or ignored.

  • Labels, SDS, and storage segregation
  • Labels and packaging

Hazard labels (CLP pictograms and signal words) give immediate warnings: flammable, corrosive, toxic, health hazard, environmental hazard, gas under pressure, and so on. Managers ensure:

  • Original labels remain readable
  • Decanted containers are labelled — never anonymous bottles of clear liquid
  • Workers understand pictograms relevant to their tasks
  • Safety data sheets (SDS)

Suppliers provide safety data sheets with detailed information on hazards, first aid, fire-fighting, accidental release, handling and storage, exposure controls, physical/chemical properties, toxicology, and disposal. Managers (or competent persons) use SDS to build COSHH assessments and emergency plans. SDS are not wallpaper — they must be accessible and reflected in real methods of work.

Storage segregation basics

Poor storage creates fires, toxic gases, and spill disasters:

Segregate incompatibles (for example acids away from cyanides or hypochlorite mixes that release chlorine; oxidisers away from flammables — follow SDS and site rules)

  • Use bunds / secondary containment for bulk liquids where required
  • Control temperature , ignition sources, and ventilation for flammables
  • Limit quantities in workrooms to what is needed for the job
  • Keep exits and spill routes clear; provide spill kits and train people to use them
  • Secure substances from unauthorised use, vandalism, or child access on mixed sites
  • Asbestos — still a manager’s problem

Asbestos was used widely in buildings for insulation, boards, tiles, coatings, gaskets, and more. Much remains in place in pre-2000 (especially pre-1980s/1990s) stock. Asbestos kills through inhaled fibres causing diseases such as mesothelioma, lung cancer, and asbestosis — often decades after exposure. There is no safe DIY approach to disturbing suspect materials.

What managers must know at overview level

  • Topic Manager takeaway
  • Presence Assume older buildings may contain asbestos until a suitable survey says otherwise

Duty to manage (non-domestic) Premises dutyholders must manage asbestos risk: find it, assess condition, record, tell people who might disturb it, monitor, and plan safe work

Disturbance risk Drilling, sanding, demolition, cable chasing, and floor works can release fibres

Licensed work Higher-risk work with certain asbestos materials requires an HSE-licensed contractor and strict controls

Non-licensed work Some lower-risk work may be non-licensed but still needs training, risk assessment, controls, and sometimes notification — not casual DIY

Never Never break, sand, or remove suspect boards/tiles/insulation without competent identification and the right regime

Refurbishment Commission the right survey before refurbishment or demolition; share findings with contractors

If workers discover a suspicious material mid-job: stop work, restrict access, report, and get competent advice . Do not bag it “carefully” with a broom. Project and exam answers that recommend “just wear a dust mask and carry on” are wrong.

Local Exhaust Ventilation (LEV)

Local Exhaust Ventilation is an engineered system that captures contaminated air at or near the source and removes it from the breathing zone — far more reliable than opening a door and hoping for the best.

Examples:

  • Extractor arms on welding bays
  • Spray booths and fume cupboards
  • On-tool extraction for sanders and cutters
  • Capturing hoods on mixing vessels or laboratory processes
  • Manager responsibilities for LEV

Right system for the contaminant and process — wrong hood design fails even if the fan is loud.

Correct use — hoods positioned close enough; dampers set; workers trained not to work upwind of the capture zone.

Maintenance — filters changed; ducts intact; fans working; damage reported.

Thorough examination and test (TExT) — LEV should be thoroughly examined and tested by a competent person at suitable intervals. A common UK benchmark taught for many systems is at least every 14 months (more often for higher-risk or heavily used systems as determined by risk and guidance). Keep records.

Indicators — airflow indicators, alarm systems, and simple user checks help daily assurance between formal tests.

Do not confuse general building ventilation or a desk fan with LEV. Moving air around can spread contamination.

  • If LEV is broken, the task may need to stop or switch to an alternative method — not continue with “just RPE.”
  • Emergency arrangements

Substance emergencies include large spills, uncontrolled releases, fires involving chemicals, and acute over-exposure. Managers ensure:

  • Spill kits and neutralisers suited to the substances present
  • Trained responders and clear alarm/evacuation rules
  • First-aid measures from SDS (eyewash, showers) actually available and working
  • Contractors know site rules before bringing their own chemicals on site
  • Waste and clean-up does not create a second exposure event
  • Worked scenarios

Scenario Routes & issues Manager controls

Cleaner decants bleach and acid descaler into unlabelled spray bottles Inhalation of chlorine if mixed; skin/eye burns; ingestion risk Ban unlabelled decanting; COSHH assessment; training; original containers; segregation

Welder works without extraction on galvanised steel indoors Inhalation of fume LEV or forced extraction design; RPE as backup; job planning; health surveillance if indicated

Electrician drills a textured coating in a 1960s school Possible asbestos fibre inhalation Check asbestos register/survey; stop if unknown; competent asbestos procedures

Woodshop with blocked extraction ducts Inhalation of wood dust (sensitiser/carcinogen concerns for some woods) Clear and test LEV; housekeeping; RPE programme; health surveillance for asthmagens

Project and exam application

When substances appear on the project:

  • Name the substance or process fume/dust , not only “chemicals”
  • State the route of entry and who is exposed
  • Prefer elimination/substitution/LEV in additional controls
  • Include information from SDS , storage, spill response, and any need for health surveillance
  • For buildings work, explicitly address asbestos information before disturbance
  • Common traps
  • Treating PPE as the main COSHH control
  • Ignoring substances generated by work (dust, fume) because they were not purchased in a drum
  • Assuming “a bit of asbestos” is safe if bonded and then drilling it anyway
  • Running production when LEV fails “just for today”
  • Storing flammables with oxidisers or food with workshop chemicals
  • Manager checklist

Inventory substances used and generated ; keep SDS available.

Assess with COSHH logic; prioritise prevent then control .

Always identify routes of entry — inhalation first among equals for many chronic risks.

Maintain and thoroughly examine/test LEV ; train users.

Manage asbestos information before any building disturbance; never DIY suspect materials.

Enforce labels, segregation, spill readiness, and reporting of ill-health symptoms.

Hazardous substances reward careful managers: small everyday decisions about extraction, substitution, and asbestos checks prevent disease that would otherwise appear years later — long after the project form is marked.