Study guide

9.2 Immediate, Underlying & Root Causes

IOSH Managing Safely Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 What Is IOSH Managing Safely? 1.2 Exam Format & Dual Assessment 1.3 Certificate Validity & Study Plan

2 Chapter 1: Introducing Managing Safely

2.1 Moral, Legal & Financial Reasons 2.2 The Accident Cost Iceberg 2.3 Responsibility & Accountability

3 Chapter 2: Assessing Risks

3.1 Hazard, Hazardous Event & Risk 3.2 Five Steps of Risk Assessment 3.3 The 5×5 Likelihood × Consequence Matrix 3.4 Residual Risk, Suitable & Sufficient, Review

4 Chapter 3: Controlling Risks

4.1 ERICPD Hierarchy of Control 4.2 Reasonably Practicable 4.3 Safe Systems of Work (SSoW) 4.4 Permits to Work

5 Chapter 4: Understanding Responsibilities

5.1 Criminal vs Civil Law 5.2 Employer & Employee Duties 5.3 Enforcement, Improvement & Prohibition Notices 5.4 Knowledge Tests & Management Systems (HSG65 / ISO 45001)

6 Chapter 5: Hazard Categories, Noise, Vibration & Substances

6.1 Six Hazard Categories 6.2 Noise Hazards & Action Values 6.3 Hand-Arm & Whole-Body Vibration 6.4 Hazardous Substances, Asbestos & LEV

7 Chapter 6: Work at Height, Manual Handling, Fire & Electricity

7.1 Work at Height 7.2 Manual Handling, Slips & Trips 7.3 Fire Safety Basics 7.4 Electricity Hazards

8 Chapter 7: Stress, Work Equipment & Other Hazards

8.1 Work-Related Stress & Psychosocial Hazards 8.2 Work Equipment & Machinery 8.3 Confined Spaces, Workplace Transport & Welfare

9 Chapter 8: Investigating Incidents

9.1 Accidents, Incidents & Near Misses 9.2 Immediate, Underlying & Root Causes 9.3 Four-Step Investigation Process 9.4 RIDDOR Reporting Overview

10 Chapter 9: Measuring Performance

10.1 Active (Proactive) vs Reactive Indicators 10.2 KPIs & Characteristics of Good Metrics 10.3 Auditing the Safety Management System 10.4 Calculating Injury Incidence & Frequency Rates 10.5 Inspections & Benchmarking

11 Chapter 10: Protecting the Environment

11.1 Environmental Basics: Pollution, Waste & Duty of Care 11.2 Reducing Environmental Impact & Environmental Management Systems

12 Chapter 11: Risk Assessment Project & Exam Day

12.1 Project Requirements & Marking 12.2 Worked Example: Four-Hazard Assessment 12.3 Written Assessment Strategy & High-Yield Review

9.2 Immediate, Underlying & Root Causes

Key Takeaways Explain This Topic AI

Immediate causes are the direct unsafe acts or unsafe conditions present at the moment of the event (oil on the floor, missing guard, not wearing PPE).

Underlying causes are the job and human factors behind those immediate failures (poor maintenance, inadequate training, time pressure, poor supervision).

Root causes are management-system failures that allowed underlying and immediate causes to exist (no planned maintenance system, no competence assurance, production prioritised over safety without controls).

A classic chain: oil spill → slip → broken arm — immediate = oil; underlying = leak left unrepaired; root = no planned maintenance / inspection regime.

Exam staples ask you to classify causes into the three levels — stop only at ‘careless worker’ and you will miss underlying and root marks.

Last updated: August 2026

9.2 Immediate, Underlying & Root Causes

Quick Answer: Immediate causes are the direct unsafe acts or conditions at the moment of the event. Underlying causes are the job/human factors that allowed those immediate failures (training, maintenance, pressure, design of the job). Root causes are management-system failures (missing systems, poor leadership priorities, no competence assurance). Fix all three levels or the same accident returns.

Once you have an accident, incident, or near miss on the table, the investigation must answer why it happened — not only what happened. Managing Safely uses a simple three-level model that mirrors good investigation practice worldwide. Assessment items love to give a short story and ask which statement is immediate , underlying , or root .

Why three levels beat “human error” alone

If your only conclusion is “the worker was careless,” you will:

  • Miss defects in plant, procedures, and supervision
  • Blame the last person in a failed system
  • Apply weak remedies (“try harder,” “toolbox talk only”)
  • See the same event repeat with a different name on the injury form

Human decisions matter — but they sit inside a system managers design and resource. The three-level model forces you to dig past the last visible mistake.

Immediate causes — what was directly present

Immediate causes are the direct unsafe acts or unsafe conditions that were present when the event occurred. They are what you would see if you stood at the scene a second before impact.

  • Unsafe acts (examples)
  • Not wearing required PPE
  • Removing or defeating a guard
  • Using the wrong tool for the job
  • Walking under a suspended load
  • Overriding an interlock “to save time”
  • Failing to isolate energy before maintenance
  • Unsafe conditions (examples)
  • Oil, water, or grease on the floor
  • Missing machine guard
  • Damaged ladder or scaffold
  • Poor lighting on a walkway
  • Trailing cables in a pedestrian route
  • Unsecured load on a forklift
  • Immediate cause type Example What the investigator sees
  • Unsafe condition Oil on floor Slippery surface at point of fall
  • Unsafe act Not wearing eye protection Splash contacts unprotected eyes
  • Both together Guard removed + reaching into motion Person contacts moving parts

Immediate causes are necessary to explain the mechanism of injury or near miss, but they are not sufficient as the end of the investigation.

Underlying causes — job and human factors behind the immediate

Underlying causes explain why the unsafe act or condition was present. They are often a mix of job factors and human factors .

Typical underlying themes

  • Theme Examples
  • Maintenance / integrity Leak known but not repaired; inspection overdue; spares not available
  • Training / competence Person never trained on the task; refresher overdue; poor induction
  • Supervision Supervisor absent or rushed; standards not enforced; mixed messages
  • Time / production pressure Unrealistic deadlines; bonus only for output; “get it done” culture
  • Equipment / workplace design Controls hard to reach; poor layout forces awkward paths; inadequate storage
  • Procedures No safe system of work; procedure out of date; permit system bypassed habitually
  • Fatigue / wellbeing Excessive overtime; night-shift issues; inadequate rest
  • Communication Shift handover missed the wet-floor hazard; contractor not briefed

Underlying causes sit one layer deeper than the oil stain or missing glove. They answer: What about the way work was organised made that immediate failure likely?

Root causes — management system failures

Root causes are failures in the management system — the policies, planning, organising, controlling, monitoring, and review arrangements that should have prevented the underlying and immediate causes.

Examples of root-level failures:

  • No planned maintenance (PM) system — breakdown maintenance only; leaks become “normal”
  • No competence assurance — people assigned tasks without proof of skill
  • Production prioritised over safety without controls — targets set with no resource for safe methods
  • Risk assessments missing, generic, or never reviewed after change
  • No effective inspection or audit regime — defects not found or not escalated
  • Inadequate leadership and accountability — managers not measured on safety outcomes
  • Poor change management — new plant or process introduced without updated controls
  • Reporting culture suppressed — previous near misses not welcomed or fixed

Root causes are organisational . Fixing only the individual and the puddle leaves the system that will recreate the next puddle and the next injured person.

Side-by-side comparison (memorise)

  • Level Question it answers Typical language Example
  • Immediate What direct act/condition caused the event? Oil, missing guard, no PPE, wrong tool Oil on the floor

Underlying Why was that act/condition allowed to exist? Poor maintenance, no training, time pressure Leak reported yesterday but not fixed

Root What system failure made that likely? No PM system, no competence process, wrong priorities Organisation has no planned inspection/maintenance regime

Worked chain — oil spill → slip → broken arm

Event: An employee walks through a production aisle, slips on oil, falls, and breaks an arm.

Immediate cause

Oil on the floor (unsafe condition). Possible related immediate factors: footwear unsuitable for the area, route not closed, no warning signs at the moment of the fall.

  • Underlying causes
  • A hydraulic hose had been leaking for some time
  • The leak was reported informally but not logged as a work order
  • Maintenance was reactive and busy with breakdowns
  • Supervisors accepted “a bit of oil” as normal for that machine
  • Cleaning was ad hoc rather than scheduled after known drips
  • Root causes
  • No effective planned maintenance system for hoses and fittings
  • No robust defect-reporting and close-out process with owners and deadlines
  • No inspection regime that would have forced escalation of recurring leaks
  • Leadership had not resourced preventive maintenance relative to production hours
  • Performance metrics rewarded uptime but not defect closure
  • Remedies at each level (preview of investigation step 3–4)
  • Level Weak fix Stronger fix
  • Immediate Mop the oil; put out a cone Clean, dry, barrier, and stop use until leak controlled

Underlying Tell the fitter to “get to it when free” Work order, temporary containment, trained response, shift handover standard

Root One angry email after the fracture Implement PM for hoses, KPI on defect closure, audit inspections, competence for maintainers

If the investigation stops at “employee should have looked where they were going,” the arm is treated as bad luck rather than a predictable system outcome .

More classification drills

  • Fact from the investigation Best level
  • Guard was not fitted at the time of injury Immediate
  • Operator had never been trained to fit the guard after cleaning Underlying
  • Company has no competence matrix or induction for machine cleaning Root

Worker removed PPE because it fogged and slowed the line Immediate (act) + look for underlying (PPE suitability, pressure)

  • Supervisors reward speed and ignore missing PPE Underlying / points toward root culture
  • No policy, monitoring, or accountability for PPE compliance Root
  • Scaffold tag missing and platform incomplete Immediate condition
  • Daily scaffold checks not done for a week due to short staffing Underlying
  • No arrangement to ensure competent scaffold inspection before use Root
  • Exam tactics

Underline the last visible failure → often immediate.

Ask “why was that true?” once → often underlying.

Ask “what system should have prevented that?” → root.

Prefer answers that name systems (PM, training assurance, inspection, risk assessment process) for root causes.

Reject options that only blame the injured person when the vignette clearly shows maintenance, training, or leadership gaps.

Manager checklist when reviewing investigation reports

Are immediate causes described factually (acts and conditions)?

Are underlying factors identified beyond personality judgments?

Is at least one credible management-system root cause stated for significant events?

Do actions address all three levels , not only cleaning and reminders?

Would the same event be less likely next month if only the immediate fix is done?

Master the three-level model and you will classify exam vignettes accurately — and run investigations that prevent recurrence instead of recycling blame.