Study guide

12.2 Worked Example: Four-Hazard Assessment

IOSH Managing Safely Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 What Is IOSH Managing Safely? 1.2 Exam Format & Dual Assessment 1.3 Certificate Validity & Study Plan

2 Chapter 1: Introducing Managing Safely

2.1 Moral, Legal & Financial Reasons 2.2 The Accident Cost Iceberg 2.3 Responsibility & Accountability

3 Chapter 2: Assessing Risks

3.1 Hazard, Hazardous Event & Risk 3.2 Five Steps of Risk Assessment 3.3 The 5×5 Likelihood × Consequence Matrix 3.4 Residual Risk, Suitable & Sufficient, Review

4 Chapter 3: Controlling Risks

4.1 ERICPD Hierarchy of Control 4.2 Reasonably Practicable 4.3 Safe Systems of Work (SSoW) 4.4 Permits to Work

5 Chapter 4: Understanding Responsibilities

5.1 Criminal vs Civil Law 5.2 Employer & Employee Duties 5.3 Enforcement, Improvement & Prohibition Notices 5.4 Knowledge Tests & Management Systems (HSG65 / ISO 45001)

6 Chapter 5: Hazard Categories, Noise, Vibration & Substances

6.1 Six Hazard Categories 6.2 Noise Hazards & Action Values 6.3 Hand-Arm & Whole-Body Vibration 6.4 Hazardous Substances, Asbestos & LEV

7 Chapter 6: Work at Height, Manual Handling, Fire & Electricity

7.1 Work at Height 7.2 Manual Handling, Slips & Trips 7.3 Fire Safety Basics 7.4 Electricity Hazards

8 Chapter 7: Stress, Work Equipment & Other Hazards

8.1 Work-Related Stress & Psychosocial Hazards 8.2 Work Equipment & Machinery 8.3 Confined Spaces, Workplace Transport & Welfare

9 Chapter 8: Investigating Incidents

9.1 Accidents, Incidents & Near Misses 9.2 Immediate, Underlying & Root Causes 9.3 Four-Step Investigation Process 9.4 RIDDOR Reporting Overview

10 Chapter 9: Measuring Performance

10.1 Active (Proactive) vs Reactive Indicators 10.2 KPIs & Characteristics of Good Metrics 10.3 Auditing the Safety Management System 10.4 Calculating Injury Incidence & Frequency Rates 10.5 Inspections & Benchmarking

11 Chapter 10: Protecting the Environment

11.1 Environmental Basics: Pollution, Waste & Duty of Care 11.2 Reducing Environmental Impact & Environmental Management Systems

12 Chapter 11: Risk Assessment Project & Exam Day

12.1 Project Requirements & Marking 12.2 Worked Example: Four-Hazard Assessment 12.3 Written Assessment Strategy & High-Yield Review

12.2 Worked Example: Four-Hazard Assessment

Key Takeaways Explain This Topic AI

Walk a generic warehouse/office hybrid with four hazards from different categories: manual handling, trip (trailing cable), chemical solvent cleaning, and forklift/pedestrian interface.

For each hazard, score current L×C with existing controls, add ERICPD-aligned further controls, then re-score residual risk so the band improves for a credible reason.

Specific, auditable controls beat vague phrases such as “more training” or “be careful.”

Managers justify scores with short scenario logic (task frequency, exposure, energy/severity) rather than inventing zeros or political inflation.

Use this worked pattern on your real site: describe activity → who/how → existing → current rating → further controls → residual → review.

Last updated: August 2026

12.2 Worked Example: Four-Hazard Assessment

Quick Answer: On a small warehouse/office hybrid , assess four hazards from different categories — e.g. manual handling of a pallet load, a trailing cable trip , solvent cleaning , and a forklift/pedestrian interface. For each: state who is at risk, existing controls, current L×C , specific ERICPD-aligned further controls , residual L×C (lower), and a review date . Specific engineering and system controls outscore vague “more training.”

This section is a model answer pattern , not a copy-paste for your own site. Change the details to match your workplace. Markers credit realism. The thinking — categories, scores, residual drop, control quality — is what transfers.

Workplace context (introduction block)

Site: “Northbay Parts” — a small distribution unit with a packing warehouse and a mezzanine office (18 employees + occasional agency pickers and visiting drivers).

Scope of this assessment: goods-in / packing floor and shared vehicle aisle during normal day shifts. Assessor: packing team leader (Managing Safely candidate). Date: course week + 3 days.

Why this site works for practice: it naturally supports physical/handling , physical trip , chemical , and mechanical/transport hazards without inventing drama.

  • Hazard 1 — Manual handling of palletised cartons (physical / handling)
  • Description

During peak dispatch, operatives manually break down mixed pallets and lift 15–22 kg cartons from low pallet height to a packing bench for 2–3 hours per shift. Some cartons are bulky and block the view of the feet.

  • Who might be harmed and how
  • Permanent packing staff and agency pickers: musculoskeletal injury (back, shoulder) from lifting/twisting
  • New starters: higher likelihood due to unfamiliar technique and pace pressure
  • Pathway: lift → awkward twist while turning to the bench → acute strain or cumulative MSD
  • Existing controls
  • Basic induction mentions “lift with care”
  • One manual pallet truck available (not always used for short moves)
  • No formal TILE assessment for this peak task
  • No job rotation rule written down
  • Current risk (existing controls)
  • Factor Score Reasoning
  • Likelihood 4 Likely High frequency; awkward heights; production pressure; weak systematic control

Consequence 3 Moderate Credible absence-level back/shoulder injury (could be higher for vulnerable individuals)

  • Current rating 12 Action band — improve within a set timescale
  • Further controls (ERICPD-aligned)

Control ERICPD level Why it helps

Introduce a scissor-lift pallet positioner so cartons are handled near waist height Reduce / Control (engineering) Lowers force and stooping → cuts likelihood

Redesign packing layout so the bench abuts the pallet face (less twisting) Reduce Reduces hazardous movement

Written short SSoW: max individual carton weight policy; two-person rule above threshold; use of pallet truck mandatory for full stack moves Control Standardises safe method

TILE-based practical coaching + observed competence check within 10 working days Control Competence for residual handling

  • Job rotation every 60 minutes during peak Control Limits exposure time
  • Team leader weekly check that the positioner is used (not bypassed) Discipline Keeps engineering control alive

Avoid relying on “send everyone on a video about lifting” as the only further control.

Residual risk

  • Factor Score Reasoning
  • Likelihood 2 Unlikely Engineering + layout + rotation make harm much less probable
  • Consequence 3 Moderate If a bad lift still occurs, harm can still be significant
  • Residual rating 6 Monitor band — maintain controls; review

Owner / timescale example: Operations supervisor to order positioner and implement SSoW within 4 weeks ; interim two-person rule starts immediately .

  • Hazard 2 — Trailing power cable across walkway (physical / trip)
  • Description

A temporary packing printer is powered by an extension lead that crosses the marked pedestrian route between packing benches and the rest area. The cable is used daily and sometimes partially covered with gaffer tape.

  • Who might be harmed and how
  • Packers, supervisors, visitors, cleaners: trip and fall → sprain, fracture, head injury depending on fall
  • People carrying loads: higher severity if they cannot break the fall
  • Existing controls
  • Yellow/black hazard tape on part of the cable
  • Verbal reminders in toolbox talks
  • No fixed power point at the printer location
  • Current risk
  • Factor Score Reasoning
  • Likelihood 4 Likely Cable on a busy route every day; tape is a weak control
  • Consequence 3 Moderate Foreseeable lost-time injury from a trip on a hard floor
  • Current rating 12 Action band
  • Further controls

Control ERICPD level

Eliminate temporary lead by installing a floor box / wall socket at the printer location Eliminate / Reduce of the trip hazard source

Until install: re-route cable overhead on a proper cable hanger or run inside a commercial cable protector ramp rated for the traffic Isolate / Control

  • Housekeeping standard: no taped cables on pedestrian routes; daily opening check Control + Discipline
  • Remove unused temporary equipment after the shift Control

“More training to watch where you walk” alone is a weak residual strategy when a socket move is reasonably practicable.

Residual risk

  • L C R Band
  • 1 Very unlikely (after fixed socket) 3 3 Monitor / maintain

Interim with a proper cable ramp only: L2 × C3 = 6 still better than 12.

  • Hazard 3 — Solvent-based cleaning of metal jigs (chemical)
  • Description

Once per shift, a designated packer degreases small metal jigs at an open bench using a solvent cleaner poured from a 5 L can into an open tray. The area has general warehouse ventilation only. Nitrile gloves are sometimes available.

  • Who might be harmed and how
  • Task packer: skin irritation / dermatitis , dizziness from vapour, eye splash
  • Nearby workers: inhalation of vapour
  • Cleaners: contact with residues if spill not cleared
  • Pathway: pour/splash → skin/eye contact; evaporation → inhalation
  • Existing controls
  • Occasional use of generic disposable gloves
  • SDS somewhere in a filing cabinet (not at point of use)
  • No local exhaust; no eye protection rule enforced
  • Open tray storage overnight sometimes
  • Current risk
  • Factor Score Reasoning
  • Likelihood 4 Likely Daily open-tray use; weak PPE consistency; poor ventilation at source
  • Consequence 3 Moderate Dermatitis / significant irritation credible; worse if eye contact
  • Current rating 12 Action band

(If the solvent were highly toxic or used in bulk without any PPE, consequence could be scored higher — stay realistic to the product SDS.)

Further controls

Control ERICPD level

Substitute with a water-based or lower-hazard cleaner approved for the jigs (check performance first) Reduce (substitution)

  • If solvent still needed: enclosed parts washer or LEV booth for degreasing Isolate / Control
  • Decant into labelled small dispensers; bund tray; no open bulk pour Control
  • Point-of-use SDS summary, glove type specified, safety spectacles mandatory for pouring Control + PPE
  • Spill kit + trained response; store locked, labelled, away from ignition sources Control
  • Supervisor weekly check of glove stock and that substitution trial is followed Discipline
  • Residual risk (after substitution + closed process)
  • L C R
  • 2 2 – 3 4–6

Likelihood falls sharply if the high-volatility solvent is removed or enclosed; consequence may fall if the substitute is milder.

  • Hazard 4 — Forklift and pedestrian shared aisle (mechanical / transport)
  • Description

Counterbalance FLT collects pallets from goods-in. The same aisle is used by pedestrians walking to the canteen and by visiting drivers on foot. Mirrors are missing at the corner. High-visibility vests are “encouraged.”

  • Who might be harmed and how
  • Pedestrians (staff, visitors, drivers): struck by / crushed by FLT — major injury or fatality possible
  • FLT operator: collision-related injury
  • Pathway: reverse or corner blind spot → contact with person
  • Existing controls
  • Trained FLT operators (certificates on file)
  • Site speed limit signed but not measured
  • Hi-vis “encouraged,” not enforced in this aisle
  • No physical segregation
  • Current risk
  • Factor Score Reasoning
  • Likelihood 3 Fairly likely Shared route daily; blind corner; mixed pedestrians
  • Consequence 5 Catastrophic Vehicle/pedestrian contact can kill or permanently disable
  • Current rating 15 Urgent action band
  • High consequence is honest for workplace transport. Do not deflate C to make the form “look fine.”
  • Further controls

Control ERICPD level

Physical segregation : fixed pedestrian walkway with barrier on one side of the aisle; ban walking in the vehicle lane Isolate

  • One-way traffic plan; convex mirrors and zone lighting at the corner Control
  • Time separation: no pedestrian transit during scheduled FLT goods-in window where practicable Control
  • Mandatory hi-vis in yard/aisle; banksman for reversing in tight spots PPE + Control
  • Enforce speed with supervisor observation; disciplinary process for shortcuts through vehicle lane Discipline

Reassess layout if volume grows — consider separate pedestrian door to canteen Eliminate pedestrian exposure on that route

Residual risk

L C R Notes

2 Unlikely 5 Catastrophic 10 Consequence often stays high (energy of FLT); likelihood must fall. Band still “action” — keep improving segregation and compliance.

This is an important teaching point: residual can remain significant when severity is inherent. Your job is to drive likelihood down with isolation and systems, not to pretend C becomes 1.

Summary scoreboard (manager view)

  • # Hazard Category Current R Residual R Priority signal
  • 1 Manual handling cartons Physical / handling 12 6 Act, then monitor
  • 2 Trailing cable Physical / trip 12 3 Fix socket — easy win
  • 3 Solvent cleaning Chemical 12 4–6 Substitute / enclose
  • 4 FLT vs pedestrians Mechanical / transport 15 10 Urgent segregation

Resource order: treat the 15 transport risk first, then the three 12 s by feasibility and speed of improvement (cable often fastest).

Scoring thinking managers use (and markers reward)

Scenario first, numbers second — describe the hazardous event before picking L and C.

Existing controls change L — do not score as if nothing is in place if training and guards already exist; do not credit paper controls that are unused.

Consequence follows energy and harm type — vehicles, falls from height, and live electricity often keep high C.

Residual must tell a story — each further control should map to a reason L or C moved.

Specific beats vague — “install barrier along bay 3 by 30 June, owner: Site Lead” beats “improve awareness.”

Review date — e.g. 12 months for this hybrid site, or 3 months for the FLT aisle until segregation is proven stable; earlier if any incident.

What not to do (exam project traps)

  • Trap Fix
  • Four trip hazards only Diversify categories when the workplace allows
  • Residual identical to current after a long control list Either strengthen controls or re-score honestly
  • “More training” as the only control for high energy risks Climb ERICPD — isolate, engineer, redesign
  • Copying this warehouse example onto an office-only job Write hazards that match your introduction
  • Leaving owners and dates blank Fill every administrative field the template shows
  • Transfer checklist for your real project

Write a 5–8 line introduction for your site.

Pick four hazards from different categories if possible.

For each, draft who/how in one sentence.

List only true existing controls.

Score current L×C with a one-line reason each.

Add 2–4 specific further controls with ERICPD labels in your notes.

Re-score residual; prioritise the highest current ratings for action first.

Set review date; submit inside the provider window.

Master this worked pattern and the project becomes a structured form, not a mystery — and the same habits make you a safer manager after the certificate is on the wall.