Study guide
6.3 Cycle-and-Soak & Soil Water Management
Irrigation Association Certified Irrigation Technician CIT
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & Field Technician Fundamentals
1.1 The CIT Credential & Exam Structure 1.2 Jobsite Safety, Utility Locates & Safety Standards 1.3 Blueprint Reading & As-Built Documentation 1.4 Equipment & Tool Usage, Manufacturer Instructions & Maintenance
2 Chapter 2: Irrigation System Components & Piping
2.1 Pipe Materials, Pressure Ratings & SDR Standards 2.2 Fitting Installation, Solvent Welding & Joint Assembly 2.3 Control Valves, Master Valves & Isolation Valves 2.4 Pressure Regulators & Backflow Prevention Assemblies 2.5 Identifying Water Supplies & Source Capacity 2.6 Water Meter Usage, Flow Testing & Leak Identification
3 Chapter 3: Sprinkler Heads & Matched Precipitation Rates
3.1 Fixed Spray Heads, Rotors & Multi-Stream Nozzles 3.2 Head-to-Head Coverage & Nozzle Spacing 3.3 Matched Precipitation Rate (MPR) Principles
4 Chapter 4: Drip & Micro-Irrigation Systems
4.1 Drip Line Components & Pressure-Compensating Emitters 4.2 Drip Filtration, Flush Valves & Air Vents 4.3 Micro-Sprays & Subsurface Drip Irrigation (SDI)
5 Chapter 5: Basic Hydraulics & Pressure Calculations
5.1 Static vs Dynamic Pressure & Elevation Head 5.2 Flow Velocity, Friction Loss & Hazen-Williams 5.3 Available Pressure Budgets & Total Dynamic Head 5.4 Pumps: Types, Components, Controls & Safety
6 Chapter 6: Hydraulic Mathematics & System Auditing
6.1 Sprinkler Precipitation Rate Formulas 6.2 Distribution Uniformity (DUlq) & Catch-Can Audits 6.3 Cycle-and-Soak & Soil Water Management
7 Chapter 7: Electrical Principles & 24 VAC Solenoid Circuits
7.1 Ohm's Law & Electrical Fundamentals 7.2 24 VAC Solenoid Construction & Coil Operation 7.3 Field Wiring, Wire Sizing & Direct-Burial Splices 7.4 Transformer Operation, Amperage Testing & Controller Service
8 Chapter 8: Controller Operations & Field Troubleshooting
8.1 Irrigation Controllers & Smart ET Controls 8.2 Electrical Troubleshooting & Multimeter Diagnostics 8.3 Hydraulic & Mechanical Troubleshooting 8.4 Spring Startup & Seasonal Commissioning
6.3 Cycle-and-Soak & Soil Water Management
Key Takeaways Explain This Topic AI
Soil infiltration rate varies drastically by texture: coarse sand absorbs water rapidly (1.0 - 2.0 in/hr), medium loam absorbs moderately (0.5 - 1.0 in/hr), while fine clay absorbs slowly (0.1 - 0.2 in/hr).
Slope significantly reduces effective intake rates; steep slopes (>12%) on clay soil can have allowable intake rates under 0.10 in/hr, creating severe surface runoff risks when sprinkler precipitation rates exceed 1.0 in/hr.
Cycle-and-soak scheduling divides total required run time into multiple shorter watering cycles interspersed with soak periods to allow water to infiltrate into the root zone without exceeding soil surface storage capacity.
Maximum allowable cycle run time before runoff begins is calculated as Max Cycle (min) = (Allowable Surface Storage Depth in inches × 60) / (PR - Soil Infiltration Rate).
Minimum soak time between active cycles must equal or exceed the time required for standing surface water to drain, typically requiring 30 to 60 minutes for fine-textured clay soils.
Last updated: August 2026
6.3 Cycle-and-Soak & Soil Water Management
Quick Answer: Cycle-and-soak scheduling divides total required irrigation run time into multiple shorter watering cycles separated by soak intervals. This prevents surface runoff when sprinkler precipitation rate (PR) exceeds soil infiltration rate. Maximum allowable cycle runtime before runoff is Max Cycle (min) = Allowable Storage Depth (in) × 60 PR (in/hr) − Infiltration Rate (in/hr) \text{Max Cycle (min)} = \frac{\text{Allowable Storage Depth (in)} \times 60}{\text{PR (in/hr)} - \text{Infiltration Rate (in/hr)}} Max Cycle (min) = PR (in/hr) − Infiltration Rate (in/hr) Allowable Storage Depth (in) × 60 . Fine clay soils require short cycles (3 to 5 minutes) and long soak periods (30 to 60 minutes).
Soil Infiltration Rates by Texture
Soil Infiltration Rate (or intake rate) is the speed at which soil absorbs water at the surface, measured in inches per hour (in/hr) . Infiltration is controlled by soil texture, structure, compaction, and pore size distribution.
Basic Soil Texture Intake Rates
Coarse Sand / Sandy Loam: 1.0 − 2.0 in/hr 1.0 - 2.0 \text{ in/hr} 1.0 − 2.0 in/hr (Large macropores allow rapid gravitational drainage, but low water holding capacity).
Loam / Silt Loam: 0.5 − 1.0 in/hr 0.5 - 1.0 \text{ in/hr} 0.5 − 1.0 in/hr (Balanced mixture of sand, silt, and clay; ideal agricultural pore matrix).
Clay / Clay Loam: 0.1 − 0.2 in/hr 0.1 - 0.2 \text{ in/hr} 0.1 − 0.2 in/hr (Dense micropores with high water retention capacity, but extremely slow intake rate).
Slope Modifiers & Compaction
When irrigation is applied on sloping terrain, gravity causes surface water to flow downhill before it can infiltrate vertically. Topographic slope significantly reduces the effective soil intake rate.
Terrain Slope Category Slope Percentage Intake Rate Reduction Factor Effective Clay Intake Rate ( 0.15 in/hr 0.15 \text{ in/hr} 0.15 in/hr Base)
- Flat / Slight 0% - 4% 1.00 (100% of base) 0.15 in/hr 0.15 \text{ in/hr} 0.15 in/hr
- Gentle Slope 5% - 8% 0.80 (80% of base) 0.12 in/hr 0.12 \text{ in/hr} 0.12 in/hr
- Moderate Slope 9% - 12% 0.60 (60% of base) 0.09 in/hr 0.09 \text{ in/hr} 0.09 in/hr
- Steep Slope > 12% 0.40 (40% of base) 0.06 in/hr 0.06 \text{ in/hr} 0.06 in/hr
- Soil Compaction Impact
Foot traffic, heavy riding mowers, and construction equipment collapse soil macro-pores. Compacted clay turf soils often exhibit intake rates as low as 0.02 − 0.05 in/hr 0.02 - 0.05 \text{ in/hr} 0.02 − 0.05 in/hr , causing immediate runoff even under low-precipitation rotors.
The Runoff Problem: PR > Infiltration Rate \text{PR} > \text{Infiltration Rate} PR > Infiltration Rate
Standard landscape spray heads apply water at 1.2 − 2.0 in/hr 1.2 - 2.0 \text{ in/hr} 1.2 − 2.0 in/hr . If a spray head applying 1.50 in/hr 1.50 \text{ in/hr} 1.50 in/hr operates continuously on a clay soil with an intake rate of 0.15 in/hr 0.15 \text{ in/hr} 0.15 in/hr , water accumulates on the surface at a rate of 1.35 in/hr 1.35 \text{ in/hr} 1.35 in/hr ( 1.50 − 0.15 1.50 - 0.15 1.50 − 0.15 ). Once soil micro-topography fills, excess water runs off onto hardscapes, causing erosion, non-point source pollution, and severe water waste.
Cycle-and-Soak Scheduling Physics
To apply the full required water volume without runoff, irrigation controllers must be programmed using Cycle-and-Soak (or Cycle/Soak). The system runs for a short cycle, pauses to allow water to soak into the root zone, and repeats until the total daily run time is achieved.
Formula for Maximum Allowable Cycle Runtime Max Cycle Duration (min) = Allowable Surface Storage Depth (in) × 60 PR (in/hr) − Infiltration Rate (in/hr) \text{Max Cycle Duration (min)} = \frac{\text{Allowable Surface Storage Depth (in)} \times 60}{\text{PR (in/hr)} - \text{Infiltration Rate (in/hr)}} Max Cycle Duration (min) = PR (in/hr) − Infiltration Rate (in/hr) Allowable Surface Storage Depth (in) × 60
Where:
Allowable Surface Storage Depth: The depth of water that surface micro-depressions can temporarily pond before runoff begins (typically 0.10 in 0.10 \text{ in} 0.10 in for flat turf, reduced to 0.05 in 0.05 \text{ in} 0.05 in or 0.08 in 0.08 \text{ in} 0.08 in on slopes).
PR \text{PR} PR : Gross zone precipitation rate (in/hr).
Infiltration Rate: Effective soil water intake rate (in/hr).
Worked Example:
A spray zone with PR = 1.40 in/hr \text{PR} = 1.40 \text{ in/hr} PR = 1.40 in/hr on a 6% gentle clay slope (effective intake = 0.12 in/hr = 0.12 \text{ in/hr} = 0.12 in/hr ) has an allowable storage depth of 0.08 in 0.08 \text{ in} 0.08 in . Max Cycle = 0.08 × 60 1.40 − 0.12 = 4.80 1.28 = 3.75 minutes \text{Max Cycle} = \frac{0.08 \times 60}{1.40 - 0.12} = \frac{4.80}{1.28} = 3.75 \text{ minutes} Max Cycle = 1.40 − 0.12 0.08 × 60 = 1.28 4.80 = 3.75 minutes
Conclusion: The controller cycle run time must not exceed 3.75 minutes per cycle. If total required daily run time is 15 minutes 15 \text{ minutes} 15 minutes , the controller must be programmed for 4 cycles of 3.75 minutes each .
Soak Duration Guidelines
The soak interval between cycles must be long enough to allow all ponded surface water to drain completely into the soil matrix.
Clay Soils: Minimum soak time of 30 to 60 minutes between active cycles.
Loam Soils: Minimum soak time of 15 to 30 minutes .
Sandy Soils: Minimal soak required (5 to 10 minutes, though cycle-and-soak is rarely needed on sand).
Evapotranspiration (ET 0 _0 0 ) & Plant Water Requirements
Water management requires calculating net crop water demand based on weather conditions:
Reference Evapotranspiration (ET 0 _0 0 ): The total water lost through evaporation from soil surfaces and transpiration from a standardized cool-season grass reference crop ( 4 in 4 \text{ in} 4 in height), measured in inches per day or week.
Plant Coefficient ( K c K_c K c ): A multiplier adjusting ET 0 _0 0 for specific plant species:
Cool-Season Turf (Tall Fescue, Kentucky Bluegrass): K c = 0.80 − 0.85 K_c = 0.80 - 0.85 K c = 0.80 − 0.85
Warm-Season Turf (Bermudagrass, Zoysia, St. Augustine): K c = 0.60 − 0.70 K_c = 0.60 - 0.70 K c = 0.60 − 0.70
Low-Water Native Shrubs: K c = 0.20 − 0.40 K_c = 0.20 - 0.40 K c = 0.20 − 0.40 Net Water Requirement (ET c ) = ET 0 × K c \text{Net Water Requirement (ET}_c\text{)} = \text{ET}_0 \times K_c Net Water Requirement (ET c ) = ET 0 × K c
Reference Table: Soil Intake Rates, Slope Modifiers & Max Cycle Times
The table below summarizes standard soil intake rates, slope adjustments, and maximum recommended initial cycle run times for typical spray head ( 1.50 in/hr 1.50 \text{ in/hr} 1.50 in/hr ) and rotor ( 0.50 in/hr 0.50 \text{ in/hr} 0.50 in/hr ) zones assuming a 0.10 in 0.10 \text{ in} 0.10 in surface storage depth.
Soil Texture Class Terrain Slope (%) Base Intake Rate (in/hr) Slope Factor Effective Intake Rate (in/hr) Spray Zone PR (1.50 in/hr) Max Cycle Rotor Zone PR (0.50 in/hr) Max Cycle Recommended Minimum Soak Time
Coarse Sand 0% - 4% (Flat) 2.00 in/hr 1.00 2.00 in/hr No Limit (PR < Intake) No Limit (PR < Intake) 0 - 5 minutes
- Sandy Loam 5% - 8% (Gentle) 0.80 in/hr 0.80 0.64 in/hr 7.0 minutes No Limit (PR < Intake) 10 - 15 minutes
- Silt Loam 0% - 4% (Flat) 0.60 in/hr 1.00 0.60 in/hr 6.7 minutes No Limit (PR < Intake) 15 - 20 minutes
- Silt Loam 9% - 12% (Moderate) 0.60 in/hr 0.60 0.36 in/hr 5.3 minutes 42.9 minutes 20 - 30 minutes
- Clay Loam 0% - 4% (Flat) 0.20 in/hr 1.00 0.20 in/hr 4.6 minutes 20.0 minutes 30 - 45 minutes
- Heavy Clay 5% - 8% (Gentle) 0.10 in/hr 0.80 0.08 in/hr 4.2 minutes 14.3 minutes 45 - 60 minutes
- Heavy Clay > 12% (Steep) 0.10 in/hr 0.40 0.04 in/hr 4.1 minutes 13.0 minutes 60+ minutes