Study guide

11.2 Air Infiltration and Blower-Door IR

Certified Infrared Thermographer Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Level II Exam 1.2 Level I vs Level II Scope and Prerequisites

2 Chapter 2: Thermometry Fundamentals

2.1 Temperature Scales and Conversions 2.2 Contact vs Non-Contact Thermometers 2.3 Identifying and Reducing Measurement Errors

3 Chapter 3: Thermal Science and Heat Transfer

3.1 Thermal Science: Temperature, Energy Units, and Heat Capacity 3.2 Heat Transfer Modes and Conduction Variables

4 Chapter 4: Advanced Infrared Theory

4.1 Radiant Power and Stefan-Boltzmann Law 4.2 Planck's Curves and Wien's Displacement Law 4.3 Real Surfaces: Emissivity, Reflectivity, Transmissivity

5 Chapter 5: Emissivity Correction Methods

5.1 Why Emissivity Correction Matters at Level II 5.2 Reference Emitter, Tape, and Paint Methods 5.3 Reflected Apparent Temperature (RAT) Methods 5.4 Emissivity Tables: Metals and Non-Metals

6 Chapter 6: Camera Parameters and Measurement Setup

6.1 The Five Required Camera Parameters 6.2 Atmospheric Temperature, RH, and Distance 6.3 IR Window Transmittance Corrections 6.4 Target Size, IFOV, and Distance-to-Spot Ratio 6.5 Detectors, Optics, and Imager Specifications

7 Chapter 7: Calibration and Advanced Error Sources

7.1 Equipment Calibration and Accuracy Specs 7.2 Cross-Verification with Contact Thermometers 7.3 Filters, Windows, and Spectral Considerations

8 Chapter 8: Severity Classification Standards

8.1 NETA ATS Table 100.18 and Repair-Priority Conventions 8.2 Absolute Temperature Limits (ANSI/IEEE/NEMA) 8.3 ISO 18434 and Machinery Severity Criteria 8.4 Building Envelope Criteria (ASTM C1060 / ISO 6781) 8.5 Load and Ambient Correction of Absolute Limits

9 Chapter 9: Electrical Pattern Analysis

9.1 Three-Phase Electrical Fault Patterns 9.2 Transformer and Switchgear Thermography 9.3 Capacitor, Bus, and Connection Anomalies 9.4 High-Voltage Inspection Conditions and Load Requirements

10 Chapter 10: Mechanical and Steam System Analysis

10.1 Bearing and Rotating Equipment Signatures 10.2 Steam Trap and Steam System Inspection 10.3 Mechanical Drive and Alignment Indicators

11 Chapter 11: Building Envelope Analysis

11.1 Insulation Defects and Thermal Bridging 11.2 Air Infiltration and Blower-Door IR 11.3 Moisture Signatures and Flat Roof Protocols 11.4 Inspection Conditions: ΔT, Wind, and Timing

12 Chapter 12: Trending and Baseline Comparison

12.1 Establishing Baselines and Documentation 12.2 Rate-of-Change and Multi-Inspection Trending 12.3 Escalation Criteria from Trend Data

13 Chapter 13: QA/QC of Level I Work

13.1 Parameter Verification and Coverage Review 13.2 Equipment Identification and Finding Reclassification 13.3 Supervisory Sign-Off Responsibilities

14 Chapter 14: Reporting Standards and Professional Ethics

14.1 Quantitative Report Content Requirements 14.2 Paired Image Documentation and Presentation 14.3 Professional Ethics and Client Communication 14.4 Image Processing and Report Generation Software

11.2 Air Infiltration and Blower-Door IR

Key Takeaways Explain This Topic AI

Air leakage moves conditioned air through cracks and penetrations; IR reveals the resulting cold or warm streaks when a pressure difference drives flow across a temperature difference

Combining a blower door with infrared multiplies contrast: depressurization draws cold outdoor air in during winter, making leak paths show as cool streaks on interior surfaces

Heating-season interior air leaks often appear as irregular cold streaks at outlets, baseboards, windows, attic hatches, and rim joists—geometry differs from full-bay missing insulation

Distinguishing air leak vs missing insulation uses pattern shape, response to pressure change, and whether the anomaly follows air paths versus cavity fill

Document blower-door pressure (e.g., −50 Pa), indoor/outdoor temperatures, and wind; IR shows where leaks are, not a substitute for quantified airtightness metrics alone

Last updated: August 2026

Air leakage is often a larger energy and comfort problem than modest insulation gaps—and it is one of infrared’s best building applications when pressure and temperature differences cooperate. Level II thermographers must explain why a cold streak appears, how blower-door (or other induced-pressure) methods improve detection, and how to separate air movement from pure conduction through missing insulation.

Air Leakage Physics in One Page

Infiltration is outdoor air entering; exfiltration is indoor air leaving. Flow requires a pressure difference (stack effect, wind, HVAC imbalance, or a blower door) and a path (cracks, gaps, penetrations). Infrared sees the thermal consequence : cold outdoor air washing a warm interior surface (winter), or warm outdoor air heating a cool interior surface (summer), or interior air warming/cooling exterior surfaces at exfiltration sites.

  • Ingredient Role
  • ΔT (air and surfaces) Temperature contrast of leaking air vs room/surface
  • ΔP (pressure) Drives flow through leaks
  • Path geometry Determines streak shape and location
  • Surface ε Drywall/paint good; shiny metal trim needs care

Without ΔT, leaking air may be nearly the same temperature as the room and invisible thermally even if the blower door measures huge CFM50. Without ΔP, many leaks barely flow and IR contrast collapses.

Heating-Season Interior Signatures (Natural and Induced)

Under winter interior conditions (indoors warmer):

  • Leak type Typical IR appearance
  • Electrical outlets / switches on exterior walls Localized cool plumes or cool receptacle boxes
  • Baseboards and sole plates Linear cool streaks along floor–wall joint
  • Window and door frames Cool edges, corners, weatherstrip failures
  • Recessed lights / attic penetrations Cool halos; sometimes wider plume under depressurization
  • Attic hatch / pull-down stairs Strong cool perimeter if unsealed
  • Rim joist / band joist Cool band; often mixed air + insulation defect
  • Plumbing and cable penetrations Spot cool anomalies
  • Fireplace dampers / duct boots Cool drafts at registers or chase

Cold streaks follow air paths —often irregular, plume-like, or edge-concentrated—rather than filling an entire stud bay uniformly. Moving your hand or a smoke pencil (where safe) can correlate with the thermal plume; the camera documents the spatial map for the report.

Exfiltration on the exterior in winter can show warm streaks at eaves, ridge vents (context), and leaky joints where warm indoor air escapes—interpret with wind and stack-effect knowledge so you do not confuse exhaust vents with uncontrolled leakage.

Combining Blower Door with IR

A blower door is a calibrated fan sealing a doorway that pressurizes or depressurizes the building to a test pressure (commonly about 50 Pa relative to outdoors for airtightness metrics). For IR:

Depressurization (most common for interior winter IR)

Building pressure set negative relative to outdoors (outdoor air pushed/pulled in through leaks).

Cold outdoor air enters leak paths.

Interior surfaces along those paths cool , increasing IR contrast.

Thermographer walks interior (and sometimes attic) mapping streaks.

Pressurization

Building pressure positive ; indoor air driven out .

Useful for exterior IR of warm exfiltration in winter, or for specific duct/chase studies.

Interior winter leak contrast for cold outdoor air is generally weaker than with depressurization because outdoor air is not being sucked in as strongly through the same paths.

  • Mode (winter) IR emphasis
  • Depressurize + interior IR Cold infiltration streaks—primary teaching case
  • Pressurize + exterior IR Warm exfiltration locations
  • Natural ΔP only Weaker, weather-dependent; still useful on windy/stack days

Level II documentation should include approximate building pressure (or at least “blower door on, depressurized”), indoor and outdoor temperatures, wind, and whether HVAC was operating. Exact airtightness results (ACH50, CFM50) come from the blower-door instrumentation; IR locates leaks for sealing priority.

Practical sequence

Prepare building per energy-audit protocol (as-found vs prepared state—follow the governing test standard/client scope).

Establish baseline IR images before the fan if you want a before/after contrast lesson for the client.

Bring building to target pressure; allow a short period for surfaces to respond (thin finishes respond faster than mass walls).

Systematic room-by-room imaging; mark priorities (large cold plumes first).

Optional: seal major leaks temporarily and re-image to prove reduction.

Restore building; report thermal map + quantitative blower-door metrics from the tester.

Distinguishing Air Leak vs Missing Insulation

This separation is a core exam and field skill.

  • Clue Air leakage lean Missing insulation lean
  • Geometry Streaks, plumes, edges, penetrations Area fill of stud/joist bays

Pressure change Pattern intensifies or appears with blower door Conductive pattern relatively stable with ΔP (same ΔT)

  • Outlets/windows Strong local effects Not required for a full-bay void
  • Between studs May cool surfaces if air washes the drywall cavity face Uniform cool bay if empty of insulation
  • Attic wind washing Cool ceiling patterns that shift with wind/pressure Settled insulation voids more static
  • Feel / smoke / theatrical fog Draft correlates Little draft if pure conduction

Hybrid reality: rim joists, attic kneewalls, and drop ceilings often have both missing insulation and air leakage. Report both mechanisms when evidence supports them. Depressurization that dramatically expands a cool zone around a penetration points to air; a cool bay that barely changes with fan-on/fan-off but sits between warm insulated bays points to insulation fill.

Fan-on / fan-off test (teaching method)

When safe and time allows:

Image suspect area at natural pressure.

Depressurize; re-image same scene within minutes.

New or intensified cool streaks → air-driven component.

Unchanged cool bay with stable geometry → more likely insulation/conductive (still verify).

Massive thermal mass and solar-loaded walls can still confuse short tests—use judgment.

Cooling Season and Reverse Patterns

In summer with air conditioning, infiltration of hot outdoor air can create warm interior streaks at leaks under appropriate pressure. Conductive heat gain through missing insulation also warms interior surfaces. Pattern geometry and pressure response still separate mechanisms better than color alone. Always write “cooling season, interior, building depressurized to …” style context in notes.

HVAC, Ducts, and Pressure Imbalance

Forced-air systems create zone pressures . A house with leaky return ducts in a vented crawlspace can pull outdoor air through envelope leaks even without a blower door. IR may show cool baseboards whenever the air handler runs. Level II should note HVAC state and not assume every leak is “only envelope construction.” Duct leakage surveys (pressure pan, duct blaster) pair with IR for complete diagnostics.

Emissivity, Reflections, and False Leaks

  • Artifact Confusion
  • Cold window glass reflections “Leak” on opposite wall
  • Metal blinds and shiny frames Wrong absolute T; pattern still usable carefully
  • Recently opened exterior door Transient cold plume—wait and recheck
  • Wet surfaces / evaporative cooling Looks cool without air leak
  • Thermal bridging at corners Cool without major airflow

Change viewing angle, use matte tape if needed, and correlate with known penetrations.

Safety and Professional Boundaries

Guard fan pressure on fragile chimneys, fireplaces, and some older buildings per blower-door best practice.

Do not claim quantitative ACH50 from IR images alone.

Coordinate with the energy auditor / testing technician when dual-certified roles are split.

Respect occupant privacy and secure outdoor conditions (wind limits for meaningful airtightness tests).

Common Traps

  • Trap Correction
  • “All cool interior spots are missing insulation” Many are air leaks or bridges
  • IR without ΔT or ΔP Low sensitivity—state limitations
  • Ignoring blower-door pressure in the report Document test pressure and mode
  • Exterior shiny metal as absolute leak temperature Qualitative / high-ε reference
  • Sealing recommendations without locating paths IR’s value is spatial prioritization
  • Summary for Recall

Air-infiltration IR depends on temperature difference plus pressure-driven flow . In winter interiors, leaks appear as cold streaks and plumes at edges and penetrations. Blower-door depressurization pulls cold outdoor air inward and amplifies those patterns for mapping. Distinguish leaks from missing insulation by geometry and pressure response (fan-on/fan-off), and always document HVAC state, ΔT, and test pressure. IR locates; blower-door instrumentation quantifies whole-building airtightness.