Study guide

6.5 Detectors, Optics, and Imager Specifications

Certified Infrared Thermographer Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Level II Exam 1.2 Level I vs Level II Scope and Prerequisites

2 Chapter 2: Thermometry Fundamentals

2.1 Temperature Scales and Conversions 2.2 Contact vs Non-Contact Thermometers 2.3 Identifying and Reducing Measurement Errors

3 Chapter 3: Thermal Science and Heat Transfer

3.1 Thermal Science: Temperature, Energy Units, and Heat Capacity 3.2 Heat Transfer Modes and Conduction Variables

4 Chapter 4: Advanced Infrared Theory

4.1 Radiant Power and Stefan-Boltzmann Law 4.2 Planck's Curves and Wien's Displacement Law 4.3 Real Surfaces: Emissivity, Reflectivity, Transmissivity

5 Chapter 5: Emissivity Correction Methods

5.1 Why Emissivity Correction Matters at Level II 5.2 Reference Emitter, Tape, and Paint Methods 5.3 Reflected Apparent Temperature (RAT) Methods 5.4 Emissivity Tables: Metals and Non-Metals

6 Chapter 6: Camera Parameters and Measurement Setup

6.1 The Five Required Camera Parameters 6.2 Atmospheric Temperature, RH, and Distance 6.3 IR Window Transmittance Corrections 6.4 Target Size, IFOV, and Distance-to-Spot Ratio 6.5 Detectors, Optics, and Imager Specifications

7 Chapter 7: Calibration and Advanced Error Sources

7.1 Equipment Calibration and Accuracy Specs 7.2 Cross-Verification with Contact Thermometers 7.3 Filters, Windows, and Spectral Considerations

8 Chapter 8: Severity Classification Standards

8.1 NETA ATS Table 100.18 and Repair-Priority Conventions 8.2 Absolute Temperature Limits (ANSI/IEEE/NEMA) 8.3 ISO 18434 and Machinery Severity Criteria 8.4 Building Envelope Criteria (ASTM C1060 / ISO 6781) 8.5 Load and Ambient Correction of Absolute Limits

9 Chapter 9: Electrical Pattern Analysis

9.1 Three-Phase Electrical Fault Patterns 9.2 Transformer and Switchgear Thermography 9.3 Capacitor, Bus, and Connection Anomalies 9.4 High-Voltage Inspection Conditions and Load Requirements

10 Chapter 10: Mechanical and Steam System Analysis

10.1 Bearing and Rotating Equipment Signatures 10.2 Steam Trap and Steam System Inspection 10.3 Mechanical Drive and Alignment Indicators

11 Chapter 11: Building Envelope Analysis

11.1 Insulation Defects and Thermal Bridging 11.2 Air Infiltration and Blower-Door IR 11.3 Moisture Signatures and Flat Roof Protocols 11.4 Inspection Conditions: ΔT, Wind, and Timing

12 Chapter 12: Trending and Baseline Comparison

12.1 Establishing Baselines and Documentation 12.2 Rate-of-Change and Multi-Inspection Trending 12.3 Escalation Criteria from Trend Data

13 Chapter 13: QA/QC of Level I Work

13.1 Parameter Verification and Coverage Review 13.2 Equipment Identification and Finding Reclassification 13.3 Supervisory Sign-Off Responsibilities

14 Chapter 14: Reporting Standards and Professional Ethics

14.1 Quantitative Report Content Requirements 14.2 Paired Image Documentation and Presentation 14.3 Professional Ethics and Client Communication 14.4 Image Processing and Report Generation Software

6.5 Detectors, Optics, and Imager Specifications

Key Takeaways Explain This Topic AI

Uncooled microbolometers operate in the 7.5–14 µm long-wave band with typical NETD of 30–50 mK; cooled photon detectors such as InSb work at 3–5 µm with NETD often below 20 mK and far shorter response times

Infraspection's electrical standard sets hard instrument minimums: spectral range 2–14 µm, a detector of at least 120 × 120 pixels, NETD of 0.1 C° (100 mK) or less at 30 °C, and manually adjustable level and gain

Imagers offering only automatic gain control are explicitly declared not sufficient for standard-compliant inspection work

IFOV equals detector pitch divided by focal length; the measurement field of view (MFOV) is larger — commonly about three times IFOV — and it is MFOV that governs accurate temperature measurement

A telephoto lens reduces the field of view and shrinks IFOV, improving spatial resolution on distant targets; a wide-angle lens does the opposite and degrades measurement accuracy on small targets

Last updated: August 2026

The ITC Level II outline opens its technical content with Camera Features and Specifications — detector types, IR resolution and optics, sensitivity, the advantages of different lenses, and the importance of IFOV and MFOV when measuring temperatures. Infraspection's electrical standard turns the same material into mandatory instrument requirements . Level II is where "which camera should we buy for this job?" becomes your question to answer.

Detector Technology

  • Uncooled microbolometer Cooled photon (quantum) detector
  • Typical materials Vanadium oxide (VOx), amorphous silicon InSb, HgCdTe (MCT), QWIP, superlattice
  • Waveband Long-wave, 7.5–14 µm Mid-wave, 3–5 µm (also short-wave variants)
  • How it works Incident IR heats the pixel, changing its resistance Photons excite charge carriers directly
  • Typical NETD 30–50 mK Often < 20 mK
  • Response time Slow, roughly 8–12 ms Very fast, microsecond integration
  • Cooling None Stirling cooler, finite service life
  • Cost Low to moderate High

Best for General electrical, mechanical, building work High-speed targets, narrow-band filtering, gas imaging, research

Why waveband matters at Level II:

Long-wave (7.5–14 µm) suffers less from solar reflection and works better through smoke and some atmospheric conditions. It is the default for building and general condition-monitoring work.

Mid-wave (3–5 µm) offers higher contrast at elevated temperatures and permits narrow-band filtering — the basis of flame-band, gas, and glass-surface measurement covered in Chapter 7.

The choice is not cosmetic. Germanium optics, IR window materials, and emissivity values are all band-specific . An emissivity table value quoted for 8–14 µm may not hold at 3–5 µm.

Published Instrument Minimums

Infraspection's Standard for Infrared Inspection of Electrical Systems & Rotating Equipment (2016) Section 7 sets requirements that appear directly on exams:

  • Requirement Value
  • Spectral range System shall operate within 2 to 14 µm
  • Spatial resolution Detector of at least 120 × 120 pixels recommended
  • Thermal sensitivity (NETD) 0.1 C° (100 mK) or less at 30 °C
  • Display Real-time visual signal, monochrome or multi-colour
  • Level and gain Must be manually adjustable in real time , independently, to specific temperature values

Not sufficient Non-imaging radiometers, visual IR thermometers, non-imaging line scanners, and imagers with automatic gain control only

That last row is the one candidates miss. An "Auto Image"-only camera is explicitly non-compliant for standard-conforming inspection, because the thermographer cannot set level and span to reveal a small ΔT against a wide scene range.

For comparison, ANSI/NETA requires imaging equipment "capable of detecting a minimum temperature difference of 1 °C at 30 °C" — a looser bar than Infraspection's 0.1 C°.

NETD in plain terms

Noise Equivalent Temperature Difference is the amount of infrared radiation, expressed in millikelvins, needed to produce a signal equal to the system's own electronic noise. Lower is better. A 50 mK camera cannot reliably resolve a 30 mK real difference — the signal is buried in noise. NETD is quoted at a stated scene temperature (usually 30 °C) and degrades at lower scene temperatures, which matters for building envelope work in cold weather.

Resolution, IFOV, and MFOV

Detector resolution is the pixel count (160 × 120 through 1280 × 1024 and beyond). It sets how many independent measurements exist across the scene.

IFOV (instantaneous field of view) is the angular size of one pixel:

IFOV = detector pitch ÷ focal length (radians; multiply by 1000 for milliradians)

At distance D, one pixel covers a spot of size IFOV × D . A camera with 1.3 mrad IFOV at 10 m resolves 13 mm per pixel.

MFOV (measurement field of view) is the crucial distinction. A single pixel that is just filled by a target does not produce an accurate temperature, because of optical spreading and detector crosstalk. Accurate radiometry commonly requires roughly a 3 × 3 pixel block on target — so MFOV ≈ 3 × IFOV .

  • Concept Meaning Consequence
  • IFOV Smallest feature you can see Detection limit
  • MFOV Smallest feature you can accurately measure Measurement limit — roughly 3× larger

Worked example. Camera IFOV = 1.3 mrad. Target: a 10 mm bolt head at 8 m.

Spot per pixel = 1.3 × 10⁻³ × 8 = 10.4 mm — the bolt barely fills one pixel.

MFOV spot = 3 × 10.4 = 31.2 mm — far larger than the bolt.

The reading will be low , averaging the bolt with cooler surroundings.

Fixes: move closer, fit a telephoto lens, or report the value as a minimum with the limitation stated.

This is the mechanism behind the classic under-reporting failure: a genuinely severe small connection graded as mild because it did not fill the measurement spot.

Lens Selection

  • Lens Field of view IFOV Use when
  • Wide-angle Large Larger (worse) Confined spaces, whole-panel overviews, building interiors
  • Standard Moderate Moderate General route work
  • Telephoto Small Smaller (better) Substations, overhead lines, elevated equipment, any distant small target
  • Close-up / macro Very small Very small PCB and component-level work

The trade is strict: narrowing the field of view improves spatial resolution . When you cannot approach a target — energised switchyard, roof-level equipment, arc-flash boundary — the telephoto lens is the only way to satisfy MFOV.

Infraspection Section 9.2.5 requires the report to record the field of view of the imager lens , and 9.2.6 requires notation of any windows, filters, or external optics used. Optics are part of the measurement chain and must be documented like any other parameter.

Applying This on the Job

Scenario A — Spec review. A client proposes a 80 × 60 pixel imager with auto-only gain for NETA-referenced switchgear surveys. Both the resolution and the absence of manual level and gain fall below Infraspection's requirements. Recommend compliant equipment.

Scenario B — Distance limit. An overhead connection at 25 m with a 1.3 mrad standard lens gives a 32.5 mm pixel and a roughly 98 mm MFOV. A 20 mm connector cannot be measured. Fit a telephoto (for example 0.65 mrad, halving both figures) or report qualitatively.

Scenario C — Band mismatch. A germanium IR window rated for long-wave use is fitted, then imaged with a mid-wave camera. Transmittance is not what the window's data sheet claims. Match window material, camera band, and the transmittance correction of Chapter 6.

Quick Answer: Uncooled microbolometers work at 7.5–14 µm with 30–50 mK NETD; cooled photon detectors work at 3–5 µm with sub-20 mK NETD and microsecond response. Infraspection requires 2–14 µm , ≥ 120 × 120 pixels , NETD ≤ 0.1 C° at 30 °C , and manual level and gain — auto-only imagers are not sufficient. IFOV = pitch ÷ focal length sets what you can see; MFOV ≈ 3 × IFOV sets what you can measure. Telephoto lenses shrink IFOV and are the answer when you cannot get closer.