Study guide
6.1 The Five Required Camera Parameters
Certified Infrared Thermographer Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Level II Exam 1.2 Level I vs Level II Scope and Prerequisites
2 Chapter 2: Thermometry Fundamentals
2.1 Temperature Scales and Conversions 2.2 Contact vs Non-Contact Thermometers 2.3 Identifying and Reducing Measurement Errors
3 Chapter 3: Thermal Science and Heat Transfer
3.1 Thermal Science: Temperature, Energy Units, and Heat Capacity 3.2 Heat Transfer Modes and Conduction Variables
4 Chapter 4: Advanced Infrared Theory
4.1 Radiant Power and Stefan-Boltzmann Law 4.2 Planck's Curves and Wien's Displacement Law 4.3 Real Surfaces: Emissivity, Reflectivity, Transmissivity
5 Chapter 5: Emissivity Correction Methods
5.1 Why Emissivity Correction Matters at Level II 5.2 Reference Emitter, Tape, and Paint Methods 5.3 Reflected Apparent Temperature (RAT) Methods 5.4 Emissivity Tables: Metals and Non-Metals
6 Chapter 6: Camera Parameters and Measurement Setup
6.1 The Five Required Camera Parameters 6.2 Atmospheric Temperature, RH, and Distance 6.3 IR Window Transmittance Corrections 6.4 Target Size, IFOV, and Distance-to-Spot Ratio 6.5 Detectors, Optics, and Imager Specifications
7 Chapter 7: Calibration and Advanced Error Sources
7.1 Equipment Calibration and Accuracy Specs 7.2 Cross-Verification with Contact Thermometers 7.3 Filters, Windows, and Spectral Considerations
8 Chapter 8: Severity Classification Standards
8.1 NETA ATS Table 100.18 and Repair-Priority Conventions 8.2 Absolute Temperature Limits (ANSI/IEEE/NEMA) 8.3 ISO 18434 and Machinery Severity Criteria 8.4 Building Envelope Criteria (ASTM C1060 / ISO 6781) 8.5 Load and Ambient Correction of Absolute Limits
9 Chapter 9: Electrical Pattern Analysis
9.1 Three-Phase Electrical Fault Patterns 9.2 Transformer and Switchgear Thermography 9.3 Capacitor, Bus, and Connection Anomalies 9.4 High-Voltage Inspection Conditions and Load Requirements
10 Chapter 10: Mechanical and Steam System Analysis
10.1 Bearing and Rotating Equipment Signatures 10.2 Steam Trap and Steam System Inspection 10.3 Mechanical Drive and Alignment Indicators
11 Chapter 11: Building Envelope Analysis
11.1 Insulation Defects and Thermal Bridging 11.2 Air Infiltration and Blower-Door IR 11.3 Moisture Signatures and Flat Roof Protocols 11.4 Inspection Conditions: ΔT, Wind, and Timing
12 Chapter 12: Trending and Baseline Comparison
12.1 Establishing Baselines and Documentation 12.2 Rate-of-Change and Multi-Inspection Trending 12.3 Escalation Criteria from Trend Data
13 Chapter 13: QA/QC of Level I Work
13.1 Parameter Verification and Coverage Review 13.2 Equipment Identification and Finding Reclassification 13.3 Supervisory Sign-Off Responsibilities
14 Chapter 14: Reporting Standards and Professional Ethics
14.1 Quantitative Report Content Requirements 14.2 Paired Image Documentation and Presentation 14.3 Professional Ethics and Client Communication 14.4 Image Processing and Report Generation Software
6.1 The Five Required Camera Parameters
Key Takeaways Explain This Topic AI
Quantitative Level II work requires five radiometric camera inputs: emissivity (ε), reflected apparent temperature (RAT), atmospheric temperature, relative humidity (RH), and distance to the target
Emissivity and RAT dominate short-path indoor accuracy; atmosphere, RH, and distance correct path attenuation that grows with range, humidity, and wavelength band
Leaving any parameter at a factory default (ε = 0.95, τ_atm = 1, distance = 1 m) can systematically bias reported temperature even when focus and range look correct
Enter parameters for the specific measurement spot and geometry before capturing the radiometric image used for quantitative reporting
IR window transmittance is an additional sixth correction when viewing through a viewport; it is not a substitute for the five free-path parameters
Last updated: August 2026
Level II thermography is quantitative radiometry with a temperature scale attached. The camera does not “know” surface temperature by magic; it infers temperature from collected infrared radiance using a model that needs object properties , background radiation , and path properties . Modern radiometric imagers expose that model as a short list of user parameters. For free-path measurements (no IR window), certification curricula and camera manuals converge on five required inputs :
- Emissivity (ε)
- Reflected apparent temperature (RAT) — also called reflected temperature, T_refl, or background temperature
- Atmospheric temperature (T_atm)
- Relative humidity (RH)
- Distance to the target (object distance)
Master these five before severity codes, trending, or report writing. Wrong parameters produce confident but incorrect temperatures — the worst kind of Level II failure.
Why Parameters Exist: The Radiance Budget
Radiation reaching the detector is not pure emission from the target. A simplified radiometric budget for a graybody target and a participating atmosphere is:
L_total ≈ τ_atm · [ε · L_bb(T_obj) + (1 − ε) · L_bb(T_refl)] + (1 − τ_atm) · L_bb(T_atm)
In words:
- Term Physical meaning Camera parameter(s)
- ε · L_bb(T_obj) Thermal emission from the object Emissivity (solves for T_obj)
- (1 − ε) · L_bb(T_refl) Radiation reflected from surroundings RAT / T_refl
τ_atm Fraction of object-path radiance that survives the air path Computed from distance , T_atm , RH (and band model)
(1 − τ_atm) · L_bb(T_atm) Atmospheric path emission / residual Same atmospheric inputs
The imager measures L_total (band-limited). It then inverts the model to report T_obj . If you feed wrong ε, RAT, or path terms, the inversion still produces a number — just not the true surface temperature.
Free path vs windowed path
The five parameters assume clear air (plus ordinary atmosphere) between lens and target. When an IR inspection window sits in the path, you also enter window transmittance (τ_window) — covered in Section 6.3. Do not confuse window τ with atmospheric τ; both reduce signal, but they are separate corrections.
Parameter 1: Emissivity (ε)
Emissivity is the fraction of blackbody radiation the surface emits at the camera’s spectral band and viewing geometry. It is the primary object property for quantitative work.
- Surface class (typical field guidance) Typical ε range Reflection risk
- Flat black paint, vinyl electrical tape 0.90–0.97 Low
- Organic nonmetals, water, many plastics 0.85–0.95 Low–moderate
- Oxidized / rough metals 0.30–0.80 Moderate–high
- Polished / bare metals 0.05–0.20 Very high
Level II rule: Prefer a measured or reference-emitter ε (tape, paint, contact cross-check from Chapter 5) over a blind handbook number for critical quantitative readings. Enter the ε that applies to the spot you measure , not a global “panel average.”
What wrong ε does
Error Typical reported temperature bias (opaque target)
ε set too high (true ε lower) Reported T usually too low — camera attributes too much of the radiance to emission
ε set too low (true ε higher) Reported T usually too high
ε wrong and high reflection Bias direction can reverse depending on whether surroundings are hotter or colder than the target
Emissivity errors are often the largest single source of quantitative mistake on short indoor paths where atmosphere is nearly transparent.
Parameter 2: Reflected Apparent Temperature (RAT)
RAT (reflected apparent temperature) is the radiometric temperature of the radiation field that the target reflects toward the camera. It is not always equal to room air temperature on a thermometer.
Sources that set RAT in practice:
- Walls, ceilings, and open doors in the target’s hemispherical view
- Hot bus work, transformers, or process equipment facing a shiny surface
- Cold sky on outdoor low-ε metals
- Your own body heat if you stand in the specular reflection path of a polished panel
- How to set RAT (field methods overview)
Method When it works Caveat
Crumpled aluminum foil “reflector” method Rough estimate of ambient IR field Follow manufacturer/training procedure; foil measures reflected field, not object T
High-ε diffuser / known reflector aimed at surroundings Indoor electrical rooms with diffuse background Avoid specular hot spots in the foil view
Assume air temperature High-ε targets (ε ≥ ~0.9) where reflection term is small Dangerous on low-ε metals
Measure with camera on a known high-ε reference nearby Stable indoor backgrounds Reference must see similar surroundings
For high-ε painted equipment, a 5–10 °C RAT error may move reported temperature only slightly. For ε = 0.1 metal, the same RAT error can dominate the reading. Level II exams repeatedly test the idea that low ε amplifies RAT mistakes .
Parameter 3: Atmospheric Temperature
Atmospheric temperature is the air temperature along the line of sight used by the camera’s atmosphere model. It helps estimate how much the path emits and, together with humidity and distance, how much the path transmits .
Practical guidance:
Use a trusted thermometer or the facility’s environmental reading for the inspection space
Outdoor long-path work: air temperature may differ from surface temperature of pavement or equipment — enter air , not the sun-loaded metal temperature
Do not confuse T_atm with RAT; they can be similar indoors but are different physical quantities
- Quantity Answers the question Typical sensor
- T_atm How warm is the air path? Air thermometer / hygrometer
- RAT What IR does the target reflect? Foil method / radiometric estimate of surroundings
- T_obj (result) What is the surface temperature? Camera inversion after parameters
- Parameter 4: Relative Humidity (RH)
Relative humidity controls water-vapor content, the main variable absorber in common LWIR atmospheric windows for industrial survey distances. Higher RH → more absorption → lower atmospheric transmittance for a given path length and temperature.
Enter RH as a percent from a hygrometer or reliable environmental station. Guessing “50%” in a steam plant or outdoor tropical survey is not Level II practice when quantitative claims are at stake.
Section 6.2 expands when RH errors matter most. For this section, remember: RH is not optional trivia; it is an input to τ_atm .
Parameter 5: Distance
Distance is the optical path length from the camera (or front of lens, per manufacturer convention) to the measurement plane on the target. The atmosphere model uses distance to scale attenuation. Distance also couples to spatial resolution (IFOV and spot size — Section 6.4), but as a radiometric parameter its first job is path correction.
- Distance practice Correct approach
- Estimating “about 10 feet” for a 30 m outdoor run Measure or pace carefully; long paths need real numbers
- Entering 1.0 m for every indoor shot (default) Update when working across a room or gallery
- Measuring to the enclosure door, not the bus Enter distance to the surface you analyze
- Changing zoom/lens without rethinking path Distance is geometric path, not “zoom level” alone
Many cameras default distance to 1 m and atmosphere to “standard” conditions. Leaving defaults on a 15 m substation shot silently assumes almost no atmospheric loss relative to the true path.
Why All Five Must Be Correct Together
It is tempting to “fix only ε” because it is famous. Level II quantitative accuracy is a system :
- Scenario Dominant risk if neglected
- Close-range indoor, painted gear, ε wrong Large T error from emissivity
- Close-range indoor, polished metal, RAT wrong Reflection-dominated false hot/cold
- Outdoor 20–50 m, high humidity, ε correct Atmospheric under-correction of true hot targets
- Mixed distances in one route Inconsistent bias across findings
- Parameters set for Image A, reused blindly for Image B Spot-specific ε/RAT/distance mismatch
Compensation myth: You cannot reliably cancel a large ε error by tweaking distance, or fix a wrong RAT by changing RH. Each parameter maps to a different physical term. Exam distractors often suggest “increase distance to fix low emissivity” — that is incorrect.
Interaction with temperature span and focus
Parameters do not replace optical basics:
- Focus — Soft focus mixes neighboring radiances; parameters cannot unmix blur
- Range / calibration interval — Wrong temperature range clips or coarsens data
- Spot size / IFOV — Undersized targets fail spatially even with perfect ε (Section 6.4)
- Spectral filters / windows — Extra optical elements need their own τ
Think of the five parameters as the radiometric solution inputs after you have a sharp, on-range, adequately resolved image.
Parameter Entry Workflow (Field Sequence)
Use a repeatable workflow so nothing is left at factory default for quantitative captures:
Step-by-step
Plan the measurement — Identify target material, access, distance, indoor vs outdoor, and whether an IR window is present.
Stabilize the camera — Power on, complete NUC/shutter as required, select correct temperature range and lens.
Measure environment — Record air temperature and RH with a thermometer/hygrometer; note wind and precipitation for outdoor work (affects heat transfer even when not direct camera params).
Determine distance — Tape, laser rangefinder, known bay dimensions, or careful pacing; enter the path length to the target surface.
Determine RAT — Use foil/reflector method or justified ambient estimate appropriate to ε; recheck if surroundings change (doors open, heaters on).
Determine emissivity — Table only when justified; prefer tape/paint/contact method for metals and critical severity calls.
Enter all five on the camera (and window τ if used) before the radiometric snapshot used for analysis.
Acquire — Focus, compose, capture radiometric image; store parameters with the file when the camera embeds them.
Verify plausibility — Compare to contact reading on a suitable surface, to sister phases, or to expected process temperatures; investigate outliers before writing P1 priorities.
Document — Report ε, RAT, T_atm, RH, distance (and window τ) with the finding so QA can reconstruct the measurement.
Workflow table for route-based surveys
- Route condition change Re-enter at least
- New material / finish ε (and often RAT)
- Move from indoor aisle to outdoor yard Distance, T_atm, RH, RAT
- Significantly closer or farther shot of same asset Distance (and check spot size)
- Weather front / humidity shift mid-day RH, T_atm
- Start viewing through IR window Window τ (+ keep five free-path params)
- Switch from painted door to bare bus ε and RAT
- Factory Defaults and Common Exam Traps
- Trap Why it fails
- “ε = 0.95 is always fine” False for metals and many real surfaces
- “RAT = air temperature always” Fails for reflective targets and nonuniform surroundings
- Ignoring RH and distance indoors Often small error — but not a license to ignore outdoors or long halls
Editing parameters after capture without understanding software Some tools recalculate; some do not change embedded analysis correctly — know your software
One global parameter set for an entire plant tour Violates spot-specific radiometry
Confusing palette / level-span with radiometric parameters Color scale is display; ε/RAT/atmosphere are measurement model
Linking to the Rest of Level II
Chapter 5 builds how to get ε and RAT right.
Section 6.2 deepens atmosphere, RH, and distance physics and traps.
Section 6.3 adds window transmittance as an optical layer.
Section 6.4 ensures the target is large enough for the IFOV so the radiance you correct is actually from the intended surface.
QA/QC chapters later will audit whether Level I work left defaults in place.
Summary for Recall
Quantitative IR cameras invert a radiance model. The five free-path parameters — emissivity, RAT, atmospheric temperature, relative humidity, and distance — supply object emission, reflected background, and atmospheric transmission/emission terms. All five must match the actual spot and geometry at the moment of capture; defaults and single-parameter “fixes” create systematic temperature bias. Use a disciplined entry workflow, document every value, and add window transmittance when a viewport is in the path. Level II professionalism is as much parameter discipline as pattern recognition.