Study guide
5.2 Reference Emitter, Tape, and Paint Methods
Certified Infrared Thermographer Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Level II Exam 1.2 Level I vs Level II Scope and Prerequisites
2 Chapter 2: Thermometry Fundamentals
2.1 Temperature Scales and Conversions 2.2 Contact vs Non-Contact Thermometers 2.3 Identifying and Reducing Measurement Errors
3 Chapter 3: Thermal Science and Heat Transfer
3.1 Thermal Science: Temperature, Energy Units, and Heat Capacity 3.2 Heat Transfer Modes and Conduction Variables
4 Chapter 4: Advanced Infrared Theory
4.1 Radiant Power and Stefan-Boltzmann Law 4.2 Planck's Curves and Wien's Displacement Law 4.3 Real Surfaces: Emissivity, Reflectivity, Transmissivity
5 Chapter 5: Emissivity Correction Methods
5.1 Why Emissivity Correction Matters at Level II 5.2 Reference Emitter, Tape, and Paint Methods 5.3 Reflected Apparent Temperature (RAT) Methods 5.4 Emissivity Tables: Metals and Non-Metals
6 Chapter 6: Camera Parameters and Measurement Setup
6.1 The Five Required Camera Parameters 6.2 Atmospheric Temperature, RH, and Distance 6.3 IR Window Transmittance Corrections 6.4 Target Size, IFOV, and Distance-to-Spot Ratio 6.5 Detectors, Optics, and Imager Specifications
7 Chapter 7: Calibration and Advanced Error Sources
7.1 Equipment Calibration and Accuracy Specs 7.2 Cross-Verification with Contact Thermometers 7.3 Filters, Windows, and Spectral Considerations
8 Chapter 8: Severity Classification Standards
8.1 NETA ATS Table 100.18 and Repair-Priority Conventions 8.2 Absolute Temperature Limits (ANSI/IEEE/NEMA) 8.3 ISO 18434 and Machinery Severity Criteria 8.4 Building Envelope Criteria (ASTM C1060 / ISO 6781) 8.5 Load and Ambient Correction of Absolute Limits
9 Chapter 9: Electrical Pattern Analysis
9.1 Three-Phase Electrical Fault Patterns 9.2 Transformer and Switchgear Thermography 9.3 Capacitor, Bus, and Connection Anomalies 9.4 High-Voltage Inspection Conditions and Load Requirements
10 Chapter 10: Mechanical and Steam System Analysis
10.1 Bearing and Rotating Equipment Signatures 10.2 Steam Trap and Steam System Inspection 10.3 Mechanical Drive and Alignment Indicators
11 Chapter 11: Building Envelope Analysis
11.1 Insulation Defects and Thermal Bridging 11.2 Air Infiltration and Blower-Door IR 11.3 Moisture Signatures and Flat Roof Protocols 11.4 Inspection Conditions: ΔT, Wind, and Timing
12 Chapter 12: Trending and Baseline Comparison
12.1 Establishing Baselines and Documentation 12.2 Rate-of-Change and Multi-Inspection Trending 12.3 Escalation Criteria from Trend Data
13 Chapter 13: QA/QC of Level I Work
13.1 Parameter Verification and Coverage Review 13.2 Equipment Identification and Finding Reclassification 13.3 Supervisory Sign-Off Responsibilities
14 Chapter 14: Reporting Standards and Professional Ethics
14.1 Quantitative Report Content Requirements 14.2 Paired Image Documentation and Presentation 14.3 Professional Ethics and Client Communication 14.4 Image Processing and Report Generation Software
5.2 Reference Emitter, Tape, and Paint Methods
Key Takeaways Explain This Topic AI
A reference emitter is a high-emissivity surface (tape, paint, or known target) placed or selected so the camera views an emission-dominated spot at the temperature of interest
Electrical tape procedure: apply matte high-ε tape, allow thermal equilibrium, set camera ε to the tape’s known value (often ~0.95), measure on the tape, not on adjacent bare metal
High-ε paint or known coatings provide durable reference spots when temporary tape is impractical; cure time and coating thickness matter
You can iterate camera ε on a surface until the IR reading matches a trusted contact thermometer, thereby back-calculating effective emissivity for that surface and geometry
Never report a metal temperature from a spot meter on bare metal while ε is set for tape — measure where the optical properties match the parameter set
Last updated: August 2026
When bare metal or unknown coatings make table lookup unreliable, Level II thermographers create or select a known emitter . This section covers electrical tape , high-emissivity paint , iteration against a contact thermometer , and ε back-calculation — the workhorse methods behind defensible quantitative readings.
What a Reference Emitter Is
A reference emitter is any surface region that:
- Has a known (or agreed high) emissivity in the camera band
- Is in good thermal contact with the object of interest (or is the object’s coating)
- Is large enough for the camera’s spot size / IFOV requirements
- Can be viewed at a favorable angle without strong specular traps
Common field references:
Reference type Typical ε (LWIR, approximate) Best use
Matte electrical insulating tape (vinyl) ~0.90–0.97 (often treated as 0.95 ) Temporary spots on bus, cabinets, pipes
- Flat black high-ε paint / spray ~0.90–0.98 Permanent test patches, lab coupons
- Factory powder coat / enamel (known good) ~0.85–0.95 When coating is already present and thick
- Commercial emissivity stickers / targets Per manufacturer (often ≥ 0.90) Repeat surveys, training
- Cavity / hole in metal (effective ε↑) Higher than flat metal Opportunistic; geometry-dependent
The reference does not change Kirchhoff’s laws for the bare metal next to it. It gives you a place to measure where ε is high and ρ is low.
Electrical Tape Method — Step-by-Step
Electrical tape is popular because it is cheap, available in plants, and optically close to a graybody in LWIR when matte and clean.
Procedure
Select location — On the component whose temperature you need (e.g., bolted lug body, bus bar surface away from arcs of safety concern). Prefer a flat area large enough for several pixels / the radiometric spot.
De-energize or follow safe work practice if contact is required near exposed live parts. Many Level II tape applications are done under LO/TO or on de-energized gear; live work requires qualified electrical safety procedures beyond this guide’s scope.
Clean lightly if grease or dust would prevent adhesion or create a thermal barrier under the tape.
Apply matte electrical tape — Use non-glossy vinyl electrical tape. Avoid shiny packaging tape, foil tape (unless used as a reflector for RAT — Section 5.3), or transparent films.
Ensure good contact — Smooth out air bubbles. Air under tape is insulation and can create a false cool or delayed reading.
Wait for thermal equilibrium — The tape must warm (or cool) to the substrate temperature. Thin tape equilibrates quickly on metal; allow extra time on poor conductors or after large load changes. Rule of practice: wait until the IR image of the tape is stable, not still ramping.
Set camera emissivity to the tape value (commonly 0.95 unless your lab has characterized that brand).
Set RAT / reflected temperature (Section 5.3) appropriately for the scene.
Measure on the tape with the spot tool or area tool entirely on the tape, not straddling tape and bare metal.
Document tape brand/type if known, ε used, RAT, load, and image with the tape visible.
Why measure on the tape, not “near” it
The bare metal still has low ε. Measuring 2 cm off the tape with ε = 0.95 reintroduces the original error. The tape is the target , not a decoration.
Limitations of tape
- Limitation Mitigation
- Temporary; may leave residue Remove per site rules; use approved materials
- Not for permanently hot surfaces that degrade adhesive Use high-temp paint or manufacturer targets
- Thin thermal resistance / imperfect contact Firm application; allow soak time; verify stability
- Tape ε not exactly 0.95 for every brand Characterize critical brands with contact method
- Safety on energized equipment Prefer planned outages / qualified live-work methods
- High-Emissivity Paint Methods
When you need a durable reference — annual surveys on the same motor terminal box, a process pipe coupon, a training panel — flat black high-ε paint or specified IR coatings outperform tape.
Procedure outline
Choose a paint or coating specified or known for high IR emissivity (matte black organic coatings are common; specialty IR paints exist for higher temperatures).
Prepare the surface per coating instructions (clean, dry, appropriate temperature).
Apply sufficient thickness so the optical properties are those of the paint, not the metal showing through. Very thin translucent coats can leave hybrid ε.
Allow full cure before quantitative work. Wet paint is not a stable optical surface.
Enter the coating’s known ε (from datasheet or your contact characterization).
Measure on the painted patch with correct RAT and geometry.
Paint vs tape decision table
- Factor Tape High-ε paint
- Setup speed Fast Slow (prep + cure)
- Permanence Low High
- Best for One-off troubleshooting Routes and baselines
- Temperature capability Limited by adhesive Depends on coating rating
- Documentation Note temporary application Map permanent patch locations
- Contact Thermometer Back-Calculation of Emissivity
Sometimes you cannot or should not alter the surface permanently, but you can access it with a trusted contact sensor (thermocouple, RTD, calibrated contact probe) during a controlled condition.
Concept
At thermal steady state on an opaque surface:
Contact instrument reads T_true (within its own uncertainty).
Camera sees radiance depending on T_true , ε , and RAT .
If RAT and other parameters are correct, there is a unique ε that makes T_IR = T_true .
That ε is the effective emissivity for your camera band, angle, and surface condition — more valuable than a generic table entry.
Iteration procedure (camera ε adjust)
Stabilize the target (constant load, no transient drafts if possible).
Measure and enter RAT correctly (Section 5.3).
Place contact sensor for a valid surface reading (good contact, correct sensor type, minimal stem conduction error).
Aim the camera at the same location (or a uniform region proven equal in temperature).
Adjust camera ε up or down until T_IR matches T_contact within acceptable tolerance (e.g., within combined uncertainties — often a few degrees depending on gear).
Record that ε as the working emissivity for this surface condition and geometry.
For future surveys of the same surface state, reuse the characterized ε — but re-check if oxidation, paint wear, or polish changes.
Directional iteration tips
- Observation Adjust ε
- T_IR higher than T_contact Increase ε (camera was under-weighting emission)
- T_IR lower than T_contact Decrease ε
(This matches the bias table in Section 5.1: low ε setting → high reported T; high ε setting → low reported T.)
Back-calculation without endless knob-turning
Some cameras and software allow solving ε from known T and RAT. Whether manual or software-assisted, the physics is the same: one known temperature + correct reflection term → effective ε .
Quality rules for contact cross-check
- Rule Why
- Contact sensor calibrated / in tolerance Garbage in, garbage out
- Same location and steady state Spatial and temporal mismatch create fake ε
- RAT correct before solving ε Wrong RAT forces wrong ε to “fit”
- Adequate spot size Camera averaging cold background → wrong T_IR → wrong ε
- Document angle and band Effective ε is not a universal material constant
- Combining Methods in One Job
A professional Level II workflow often chains methods:
Survey qualitatively to find candidates.
On critical findings, apply tape or use existing high-ε coating .
Measure RAT for the scene.
Report quantitative T from the reference emitter.
Optionally, on a sample of coating types in the plant, characterize ε with contact once and build a site emissivity list (better than generic web tables).
Exam scenario: “Camera reads 42 °C on bare copper; contact reads 71 °C”
Reasoning path:
Large discrepancy on bare metal suggests ε/RAT setup , not necessarily a broken camera.
Apply tape, set ε ≈ 0.95, remeasure on tape — reading should approach contact if contact is on the same isothermal region.
Or leave the bare surface, set RAT carefully, and iterate ε until IR matches contact; expect a low ε for clean copper.
Do not average 42 and 71 and call it science.
Common Mistakes (Level II QA Targets)
- Mistake Correct practice
- Spot on bare metal, ε = 0.95 “because that is the default” Tape/paint or measured ε + RAT
- Tape applied but measurement off-tape Spot fully on tape
- No wait for tape equilibrium Wait for stable image
- Solving ε with wrong RAT Fix reflection first or together
- Using glossy decorative tape Matte electrical or known IR tape
- One ε for all plant metals forever Reassess when surface state changes
- Ignoring IFOV — tape smaller than spot Larger patch or closer distance / appropriate lens
- Summary for Recall
Reference emitters let you measure where ε is high and known . Electrical tape : apply, equilibrate, set ε (often 0.95), measure on the tape. High-ε paint : durable patches for routes and baselines after proper cure. Contact back-calculation : with correct RAT, adjust camera ε until T_IR equals T_contact to obtain effective emissivity for that surface. Level II discipline is matching the spot location , optical properties , and parameter set — never reporting a polished-metal temperature under a paint emissivity setting.