Study guide
12.1 Establishing Baselines and Documentation
Certified Infrared Thermographer Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Level II Exam 1.2 Level I vs Level II Scope and Prerequisites
2 Chapter 2: Thermometry Fundamentals
2.1 Temperature Scales and Conversions 2.2 Contact vs Non-Contact Thermometers 2.3 Identifying and Reducing Measurement Errors
3 Chapter 3: Thermal Science and Heat Transfer
3.1 Thermal Science: Temperature, Energy Units, and Heat Capacity 3.2 Heat Transfer Modes and Conduction Variables
4 Chapter 4: Advanced Infrared Theory
4.1 Radiant Power and Stefan-Boltzmann Law 4.2 Planck's Curves and Wien's Displacement Law 4.3 Real Surfaces: Emissivity, Reflectivity, Transmissivity
5 Chapter 5: Emissivity Correction Methods
5.1 Why Emissivity Correction Matters at Level II 5.2 Reference Emitter, Tape, and Paint Methods 5.3 Reflected Apparent Temperature (RAT) Methods 5.4 Emissivity Tables: Metals and Non-Metals
6 Chapter 6: Camera Parameters and Measurement Setup
6.1 The Five Required Camera Parameters 6.2 Atmospheric Temperature, RH, and Distance 6.3 IR Window Transmittance Corrections 6.4 Target Size, IFOV, and Distance-to-Spot Ratio 6.5 Detectors, Optics, and Imager Specifications
7 Chapter 7: Calibration and Advanced Error Sources
7.1 Equipment Calibration and Accuracy Specs 7.2 Cross-Verification with Contact Thermometers 7.3 Filters, Windows, and Spectral Considerations
8 Chapter 8: Severity Classification Standards
8.1 NETA ATS Table 100.18 and Repair-Priority Conventions 8.2 Absolute Temperature Limits (ANSI/IEEE/NEMA) 8.3 ISO 18434 and Machinery Severity Criteria 8.4 Building Envelope Criteria (ASTM C1060 / ISO 6781) 8.5 Load and Ambient Correction of Absolute Limits
9 Chapter 9: Electrical Pattern Analysis
9.1 Three-Phase Electrical Fault Patterns 9.2 Transformer and Switchgear Thermography 9.3 Capacitor, Bus, and Connection Anomalies 9.4 High-Voltage Inspection Conditions and Load Requirements
10 Chapter 10: Mechanical and Steam System Analysis
10.1 Bearing and Rotating Equipment Signatures 10.2 Steam Trap and Steam System Inspection 10.3 Mechanical Drive and Alignment Indicators
11 Chapter 11: Building Envelope Analysis
11.1 Insulation Defects and Thermal Bridging 11.2 Air Infiltration and Blower-Door IR 11.3 Moisture Signatures and Flat Roof Protocols 11.4 Inspection Conditions: ΔT, Wind, and Timing
12 Chapter 12: Trending and Baseline Comparison
12.1 Establishing Baselines and Documentation 12.2 Rate-of-Change and Multi-Inspection Trending 12.3 Escalation Criteria from Trend Data
13 Chapter 13: QA/QC of Level I Work
13.1 Parameter Verification and Coverage Review 13.2 Equipment Identification and Finding Reclassification 13.3 Supervisory Sign-Off Responsibilities
14 Chapter 14: Reporting Standards and Professional Ethics
14.1 Quantitative Report Content Requirements 14.2 Paired Image Documentation and Presentation 14.3 Professional Ethics and Client Communication 14.4 Image Processing and Report Generation Software
12.1 Establishing Baselines and Documentation
Key Takeaways Explain This Topic AI
A baseline is a documented reference thermal state of equipment under known operating conditions—not merely the first pretty picture saved on a camera
Baseline packages must record load, ambient (and related environment), camera parameters (ε, RAT, distance, atmosphere/window), equipment ID/location, date/time, and the thermogram plus visual image
Establish baselines on new or major-modified equipment after commissioning at representative load; re-baseline after repair, rebuild, or configuration change that alters normal thermal behavior
Same-component baseline trending complements (does not replace) similar-component NETA-style snapshot severity when peers exist
Level II owns baseline quality: comparable geometry, correct radiometry, and metadata complete enough that a future inspector can reproduce the comparison
Last updated: August 2026
Snapshot severity (Chapter 8) answers “Is this abnormal right now versus a peer or a design limit?” Trending answers “Is this changing in a way that predicts failure or demands earlier action?” Both skills require a trustworthy baseline —a documented reference thermal state against which later inspections are compared. Level II thermographers design baseline programs, not just collect random archives.
What a Baseline Is (and Is Not)
Concept Definition Level II implication
Baseline image/set Quantitative thermogram(s) of a specific asset under known, recorded conditions, with full metadata Enables same-component ΔT over time
Pretty archive Image without load, ambient, parameters, or equipment ID Nearly useless for defensible trending
Peer reference Similar component at the same survey (NETA-style) Snapshot severity; different from multi-year baseline
OEM “normal” table Generic design guidance Complements but does not replace site-specific baselines
A baseline is a measurement package , not a single JPEG. Future inspectors must recreate enough of the original conditions to interpret rate of change without inventing history.
Minimum Contents of a Baseline Package
Every baseline (and every later trend point) should capture the fields below. Missing fields create false trends or force “cannot compare” conclusions.
Field What to record Why it matters
Equipment ID / location Unique asset tag, panel ID, phase, cubicle, bearing position, route stop Wrong asset = meaningless trend
Date and time Local date/time; note shift if relevant Timeline for rate-of-change
Load / process state Amps or % rated, production rate, RPM, steam load, HVAC mode I²R and process heat dominate temperature
Ambient / environment Air temperature; for outdoors wind/sun; for buildings indoor–outdoor ΔT when relevant Absolute T and some ΔT contexts shift with ambient
- Camera parameters Emissivity, RAT, distance, atmospheric temp, RH; window τ if used Radiometric comparability
- Geometry Lens, stand-off, angle, IR window ID Spot-size and path errors
Thermogram + visual Radiometric file preferred; annotated ΔT regions of interest (ROI) Pattern + identification
Reference description What was compared (same lug over time; peer phase; baseline ROI) Clarity for later reviewers
- Measured values T_suspect (or ROI stats), optional T_peer, ambient Quantitative core
- Inspector / camera ID Name/cert level, camera serial or model Traceability and QA
- Worked minimum label (electrical connection)
- Asset: MCC-3 / Starter 12 / Load side Phase B lug
- 2026-03-12 14:20 Load: 48 A (62% FLA) Ambient: 24 °C
- ε = 0.95 (oxidized lug + tape reference), RAT = 24 °C, d = 1.2 m, no window
- ROI max = 41 °C; Phase A peer = 36 °C; ΔT_peer = 5 °C
- Camera: Model X / SN … Inspector: J. Doe, Level II
That package can support both peer severity today and same-lug trend next year.
Same-Component Baseline vs Peer Snapshot
Comparison Best for Weak when
Similar component, similar load (NETA-style) Connection faults, phase imbalance signatures Unique assets; intentional unbalance
Same component vs its baseline Slow degradation, post-repair verification, assets without peers Baseline missing or conditions not comparable
Absolute / OEM limits Design temperature ceilings Does not show early peer ΔT faults
Level II rule: Use both when possible. A lug can sit in Priority 4 versus peers (small ΔT) yet still show a rising same-component trend that justifies earlier re-inspection. Conversely, a one-time peer ΔT of 22 °C needs Priority 2 action even if last year’s baseline is incomplete.
- When to Establish Baselines
- New and major-modified equipment
Baseline after commissioning when the asset is:
- Mechanically/electrically complete and accepted for service
- At representative operating load (electrical IR commonly ≥ ~40% of rated when safe; prefer higher)
- Thermally steady (not mid-ramp after a cold start unless the program explicitly trends start-up signatures)
- Accessible with the same IR path you will use later (window installed, covers policy defined)
- Situation Baseline timing
- New switchgear lineup After energization and loaded operation; per circuit or representative loads
- New motor / gearbox After break-in at normal process load and stable bearing temperatures
Building envelope after renovation Under valid envelope ΔT conditions (Chapter 8 / 10), not on a mild spring day only
Steam system after trap replacement At normal steam pressure/load once the circuit is stable
Do not treat factory FAT images under unknown load, or construction-phase cold equipment, as the plant’s operating baseline unless the program documents them as a separate “as-built cold” set.
Fleet / route programs
For predictive maintenance routes, baselines are often established on the first valid survey of each stop after the program starts—or when a stop is added. Level II standardizes ROI placement (same bolt head, same bearing housing location) so multi-year plots compare the same physical point.
When to Re-Baseline
A baseline becomes obsolete when the asset’s normal thermal identity changes for reasons other than the fault mode you are monitoring.
Trigger Action
Repair or replacement of the monitored component (retorque, new lug, new bearing, new trap) Re-baseline after return to stable service at comparable load
Major modification (rewire, different fuse type, coupling change, insulation upgrade) New baseline; archive old series as closed
IR path change (new IR window, different stand-off policy, permanent shield) Re-baseline with new path parameters
- Coating / surface change that alters emissivity Re-establish ε method and re-baseline temperatures
- Load profile permanent change (upsized motor, different process duty) New “normal” baseline under the new duty
Suspected bad historical baseline (wrong ε, wrong asset ID) Invalidate; create a corrected baseline rather than trend garbage
Post-repair verification is both a QA step and a new baseline seed: confirm the anomaly cleared and capture the new normal under load for future trending.
Documentation Discipline and Storage
- Practice Rationale
- Radiometric originals + report derivatives Later re-analysis with corrected ε if needed
- Consistent file naming (site-asset-date) Findable multi-year sets
- ROI templates / overlays Same measurement point each visit
- Database fields for load and ambient Enable normalized trends (Section 12.2)
- Link work orders to IR finding IDs Close the loop after repair re-baseline
Paper thumbnails without parameters fail insurance, ISO-style condition monitoring programs, and Level II QA review.
Quality Checks Before Accepting a Baseline
Identity: Asset tag matches the physical equipment and single-line / P&ID location.
Radiometry: ε and RAT defensible; focus sharp; spot size adequate for the target.
Load: Adequate and recorded; not a no-load energization photo labeled “baseline.”
Steady state: Temperatures not climbing rapidly after a load step unless noted.
Completeness: All minimum metadata fields present.
Peer context: Where peers exist, record peer ΔT as well as absolute ROI temperature—future readers get both lenses.
Worked Scenarios
Scenario A — New feeder. After commissioning, Phase A/B/C lugs are balanced within 2 °C at 55% load. Baseline package stored with parameters and currents. One year later Phase B is +8 °C vs peers and +12 °C vs its own baseline at similar load → early degradation signal even if still Priority 4 by peer band.
Scenario B — Missing load. Archive image shows a warm breaker with no amps recorded. Cannot use as quantitative baseline; schedule a proper baselining survey.
Scenario C — After repair. Priority 2 connection repaired; re-inspect at load shows ΔT_peer = 1 °C. Re-baseline the repaired lug; do not keep trending against the pre-repair hotspot as if it were “normal.”
Scenario D — Window retrofit. IR window installed on a gear door. Old open-door baselines are not path-comparable; establish through-window baselines with measured/known τ.
Scenario E — Wrong asset. Baseline labeled “Pump 4 drive end” was actually non-drive end. Level II invalidates the series and starts a correct baseline rather than inventing a failure trend.
Common Traps
- Trap Correct Level II view
- “First image ever” without metadata = baseline Incomplete; not trendable
- Baselining at 10% electrical load Inadequate for connection-sensitive programs; re-baseline at ≥ ~40%
- Never re-baselining after repair Trends compare fault to repaired state incorrectly
- Changing ε every year without notes False temperature trends
- Using only palette color memory Not quantitative
- Mixing peer ΔT and ambient ΔT in one chart without labels Confuses rate-of-change
- Summary for Recall
A baseline is a full documentation package : equipment ID, date/time, load , ambient/environment , camera parameters , geometry/path, thermogram + visual, and measured ROI values. Establish baselines on new/commissioned equipment at representative steady load , and re-baseline after repair or modification . Same-component baselines power multi-year trending; they complement peer-based NETA snapshot severity. Level II refuses pretty-but-empty archives and builds comparisons future inspectors can trust.