Study guide

6.1 Kill Sheet Fundamentals & Pre-Recorded Data

IWCF Level 2 Drilling Well Control Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Well Control Introduction, Pressure Fundamentals & Well Barriers

1.1 Principles of Well Control & Incident Impact 1.2 Hydrostatic Pressure, Formation Pressure & Pressure Gradients 1.3 Well Barrier Philosophy & Barrier Management

2 Chapter 2: Rig Hydraulics, Circulating System & Formation Strength

2.1 Circulating System & Annular Friction Losses 2.2 Equivalent Circulating Density (ECD) & Slow Circulation Rates (SCR) 2.3 Formation Integrity Testing (FIT, LOT) & MAASP

3 Chapter 3: Causes of Kicks & Tripping Mechanics

3.1 Primary Causes of Well Influxes 3.2 Swabbing and Surging Dynamics 3.3 Tripping Operations & Trip Tank Monitoring

4 Chapter 4: Kick Detection & Warning Signs

4.1 Positive Kick Indicators 4.2 Warning Signs of an Impending Kick 4.3 Shallow Gas Hazards & Diverter Operations

5 Chapter 5: Influx Behavior, Shut-In Procedures & Pressures

5.1 Influx Behavior & Gas Migration 5.2 Shut-In Procedures for Drilling, Tripping & Out of Hole 5.3 Shut-In Drill Pipe Pressure (SIDPP), Shut-In Casing Pressure (SICP) & Pit Gain

6 Chapter 6: Kill Sheet Calculations & Well Control Methods

6.1 Kill Sheet Fundamentals & Pre-Recorded Data 6.2 Kill Mud Weight, ICP & FCP Calculations 6.3 Well Control Methods: Driller's, Wait and Weight & Volumetric

7 Chapter 7: Well Control During Casing & Cementing

7.1 Running & Pulling Casing and Liner: Swab, Surge, Returns & Shut-In 7.2 Cementing Casing and Liner: BHP Changes, Verification & Flow During Cementing

8 Chapter 8: Blowout Preventers (BOPs) & Stack Arrangements

8.1 Ram-Type Blowout Preventers 8.2 Annular Blowout Preventers 8.3 BOP Stack Configurations & Drilling Spools

9 Chapter 9: Choke Manifolds, Auxiliary Equipment & Control Systems

9.1 Choke Manifolds, Chokes & Flow Routing 9.2 Internal Blowout Preventers & Auxiliary Equipment 9.3 BOP Hydraulic Control Systems (Closing Units)

10 Chapter 10: Testing, Maintenance & Subsea Systems

10.1 BOP Pressure Testing & Function Testing 10.2 Well Control Drills & Operational Risk Management 10.3 Subsea Well Control Equipment Overview

6.1 Kill Sheet Fundamentals & Pre-Recorded Data

Key Takeaways Explain This Topic AI

The standard IWCF kill sheet provides a pre-engineered calculation framework that eliminates guesswork and mathematical error during time-critical well control emergencies.

Drill string internal volumes are calculated component-by-component (drill pipe, heavy-weight drill pipe, drill collars) using capacity formulas: C id = I D 2 1029.4 bbl/ft C_{\text{id}} = \frac{ID^2}{1029.4}\text{ bbl/ft} C id ​ = 1029.4 I D 2 ​ bbl/ft (or metric I D 2 1273.2 l/m \frac{ID^2}{1273.2}\text{ l/m} 1273.2 I D 2 ​ l/m ).

Annular capacity represents the volume between the wellbore or casing wall and the drill string exterior ( C ann = D 2 2 − D 1 2 1029.4 bbl/ft C_{\text{ann}} = \frac{D_2^2 - D_1^2}{1029.4}\text{ bbl/ft} C ann ​ = 1029.4 D 2 2 ​ − D 1 2 ​ ​ bbl/ft ), subdivided into open hole and cased hole intervals.

Volumetric capacities divided by mud pump output ( V stk V_{\text{stk}} V stk ​ ) yield exact pump stroke counts: surface-to-bit strokes dictate the step-down schedule, while bit-to-surface strokes govern annular displacement.

SCR pressures are re-recorded every tour and after mud, bit or BHA changes; leak-off (LOT/FIT) data is entered after each shoe test, and MAASP is recalculated whenever the mud weight changes.

Last updated: October 2026

During a well control emergency, high stress, time constraints, and complex downhole dynamics make manual, ad-hoc calculations hazardous. The standard IWCF kill sheet is a systematic, pre-engineered calculation template designed to organize well geometry, tubular capacities, pump outputs, and hydraulic pressure baselines before a kick occurs. By pre-recording well data during routine operations, the rig team ensures that once a kick is detected and the well is secured, only three live variables—Shut-In Drill Pipe Pressure (SIDPP), Shut-In Casing Pressure (SICP), and Pit Gain—are needed to immediately establish the complete kill plan.

Purpose and Architecture of the IWCF Kill Sheet

The kill sheet fulfills three critical operational functions:

Continuous Baseline Monitoring: Tracks wellbore volume changes, circulation times, and formation fracture limits as drilling deepens.

Rapid Post-Kick Parameter Determination: Converts raw shut-in pressures into Kill Mud Weight (KMW), Initial Circulating Pressure (ICP), Final Circulating Pressure (FCP), and revised Maximum Allowable Annular Surface Pressure (MAASP).

Operational Roadmap for Choke Manipulation: Establishes the stroke-by-stroke drill pipe pressure step-down table that the choke operator follows to maintain constant bottom-hole pressure.

Functional Sections of the Kill Sheet

Well Geometry & Depths: Hole diameter, casing outer/inner diameter, casing shoe Measured Depth (MD) and True Vertical Depth (TVD), total well MD and TVD, and current drilling fluid density.

Drill String Internal Capacity: Dimensions, unit capacities, lengths, and calculated internal volumes for drill pipe (DP), heavy-weight drill pipe (HWDP), and drill collars (DC).

Annular Capacity: Capacities and volumes for casing-by-drill pipe, open hole-by-drill pipe, open hole-by-HWDP, and open hole-by-drill collars, plus surface choke line volumes.

Mud Pump Displacement Data: Triplex pump liner size, stroke length, volumetric efficiency, and displacement output per stroke ( V stk V_{\text{stk}} V stk ​ ) for each active pump.

Pre-Recorded Hydraulics: Slow Circulation Rate (SCR) pressures measured across multiple pump speeds (e.g., 20, 30, and 40 SPM) through both the normal flowline and the choke line.

Formation Fracture Data: Leak-Off Test (LOT) pressure, Equivalent Mud Weight (EMW), and initial MAASP.

Drill String Internal Capacity & Volume Calculations

The drill string serves as a clean, uncontaminated fluid conduit from surface to the bit nozzles. Because wall thickness and internal diameters vary across tubular components, the internal volume is calculated segment by segment.

Capacity Formulas

In oilfield imperial units, internal capacity ( C id C_{\text{id}} C id ​ ) in barrels per linear foot ( bbl/ft \text{bbl/ft} bbl/ft ) is calculated from the pipe inner diameter ( I D ID I D , in inches):

C id = I D 2 1029.4 [ bbl/ft ] C_{\text{id}} = \frac{ID^2}{1029.4}\quad [\text{bbl/ft}] C id ​ = 1029.4 I D 2 ​ [ bbl/ft ]

In metric units, internal capacity in liters per linear meter ( l/m \text{l/m} l/m ) is:

C id = I D 2 1273.2 [ l/m ] C_{\text{id}} = \frac{ID^2}{1273.2}\quad [\text{l/m}] C id ​ = 1273.2 I D 2 ​ [ l/m ]

Where I D ID I D is in millimeters.

Segment Volume Determination

The fluid volume of each tubular component is the product of its length ( L L L ) and unit capacity ( C id C_{\text{id}} C id ​ ):

V section = L × C id V_{\text{section}} = L \times C_{\text{id}} V section ​ = L × C id ​

Total drill string volume ( V string V_{\text{string}} V string ​ ) is the cumulative sum of all internal tubular volumes:

V string = V DP + V HWDP + V DC V_{\text{string}} = V_{\text{DP}} + V_{\text{HWDP}} + V_{\text{DC}} V string ​ = V DP ​ + V HWDP ​ + V DC ​

Tubular Component Outer Diameter ( O D OD O D ) Inner Diameter ( I D ID I D ) Capacity ( C id C_{\text{id}} C id ​ ) Typical Length Range Volume Contribution

Drill Pipe (DP) 5.000 in 5.000\text{ in} 5.000 in 4.276 in 4.276\text{ in} 4.276 in 0.01776 bbl/ft 0.01776\text{ bbl/ft} 0.01776 bbl/ft 8,000 − 16,000 ft 8{,}000 - 16{,}000\text{ ft} 8 , 000 − 16 , 000 ft 140 − 280 bbl 140 - 280\text{ bbl} 140 − 280 bbl (Dominant string volume)

Heavy-Weight DP (HWDP) 5.000 in 5.000\text{ in} 5.000 in 3.000 in 3.000\text{ in} 3.000 in 0.00874 bbl/ft 0.00874\text{ bbl/ft} 0.00874 bbl/ft 450 − 900 ft 450 - 900\text{ ft} 450 − 900 ft 4 − 8 bbl 4 - 8\text{ bbl} 4 − 8 bbl (Thick-walled transition pipe)

Drill Collars (DC) 6.500 in 6.500\text{ in} 6.500 in 2.8125 in 2.8125\text{ in} 2.8125 in 0.00768 bbl/ft 0.00768\text{ bbl/ft} 0.00768 bbl/ft 300 − 600 ft 300 - 600\text{ ft} 300 − 600 ft 2.3 − 4.6 bbl 2.3 - 4.6\text{ bbl} 2.3 − 4.6 bbl (Low internal volume, high steel mass)

Note

In field calculations, internal upsets and connection tapers cause minor deviations from nominal capacity. Rig teams use standardized API tubular capacity tables or verified pipe manufacturer data sheets when completing the official kill sheet.

Annular Capacity Sections & Wellbore Volumes

The annular space is the void between the outer diameter of the drill string ( D 1 D_1 D 1 ​ ) and the inner diameter of the casing or open hole ( D 2 D_2 D 2 ​ ).

Annular Capacity Formulas

In imperial units:

C ann = D 2 2 − D 1 2 1029.4 [ bbl/ft ] C_{\text{ann}} = \frac{D_2^2 - D_1^2}{1029.4}\quad [\text{bbl/ft}] C ann ​ = 1029.4 D 2 2 ​ − D 1 2 ​ ​ [ bbl/ft ]

In metric units:

C ann = D 2 2 − D 1 2 1273.2 [ l/m ] C_{\text{ann}} = \frac{D_2^2 - D_1^2}{1273.2}\quad [\text{l/m}] C ann ​ = 1273.2 D 2 2 ​ − D 1 2 ​ ​ [ l/m ]

Annular Segmentation

The annular volume is divided into distinct sections reflecting changing hole and tubular diameters:

Casing Annulus ( V csg-DP V_{\text{csg-DP}} V csg-DP ​ ): Volume between casing ID and drill pipe OD from surface to casing shoe depth.

Open Hole vs. Drill Pipe ( V OH-DP V_{\text{OH-DP}} V OH-DP ​ ): Volume between drilled hole diameter and drill pipe OD from casing shoe to top of HWDP.

Open Hole vs. HWDP ( V OH-HWDP V_{\text{OH-HWDP}} V OH-HWDP ​ ): Volume between drilled hole diameter and HWDP OD.

Open Hole vs. Drill Collars ( V OH-DC V_{\text{OH-DC}} V OH-DC ​ ): Volume between drilled hole diameter and collar OD. Because drill collars have large outer diameters, this section exhibits the lowest unit capacity and smallest clearance, resulting in the highest annular fluid velocities.

Surface Choke Line Volume ( V choke V_{\text{choke}} V choke ​ ): Fluid volume of high-pressure lines connecting the BOP stack to the choke manifold. On subsea rigs, long choke and kill lines (extending through thousands of feet of water) contain substantial volumes that must be accounted for.

Worked Example: Annular Volume, Strokes and Time

Open hole of 8-1/2 in around 5 in drill pipe, 1,000 ft long; the pump delivers 0.100 bbl/stroke at 30 SPM.

Annular capacity: 8.5 2 − 5.0 2 1029.4 = 72.25 − 25.00 1029.4 = 0.0459 bbl/ft \frac{8.5^2 - 5.0^2}{1029.4} = \frac{72.25 - 25.00}{1029.4} = 0.0459\text{ bbl/ft} 1029.4 8. 5 2 − 5. 0 2 ​ = 1029.4 72.25 − 25.00 ​ = 0.0459 bbl/ft

  • Volume: 1,000 × 0.0459 = 45.9 bbl 1{,}000 \times 0.0459 = 45.9\text{ bbl} 1 , 000 × 0.0459 = 45.9 bbl
  • Strokes: 45.9 ÷ 0.100 = 459 strokes 45.9 \div 0.100 = 459\text{ strokes} 45.9 ÷ 0.100 = 459 strokes
  • Time at 30 SPM: 459 ÷ 30 = 15.3 minutes 459 \div 30 = 15.3\text{ minutes} 459 ÷ 30 = 15.3 minutes

Pump output per minute is the displacement per stroke multiplied by the pump rate ( 0.100 × 30 = 3.0 bbl/min 0.100 \times 30 = 3.0\text{ bbl/min} 0.100 × 30 = 3.0 bbl/min ), so the same result is 45.9 ÷ 3.0 = 15.3 45.9 \div 3.0 = 15.3 45.9 ÷ 3.0 = 15.3 minutes.

Total Annular & Open Hole Volumes

Total Open Hole Annular Volume ( V OH V_{\text{OH}} V OH ​ ): The fluid volume in the open hole below the casing shoe: V OH = V OH-DC + V OH-HWDP + V OH-DP(open) V_{\text{OH}} = V_{\text{OH-DC}} + V_{\text{OH-HWDP}} + V_{\text{OH-DP(open)}} V OH ​ = V OH-DC ​ + V OH-HWDP ​ + V OH-DP(open) ​

Total Annular Volume ( V annulus V_{\text{annulus}} V annulus ​ ): The cumulative annular volume from the bit to the surface wellhead: V annulus = V csg-DP + V OH + V choke V_{\text{annulus}} = V_{\text{csg-DP}} + V_{\text{OH}} + V_{\text{choke}} V annulus ​ = V csg-DP ​ + V OH ​ + V choke ​

Total Well System Volume: The complete fluid contents of the wellbore: V system = V string + V annulus V_{\text{system}} = V_{\text{string}} + V_{\text{annulus}} V system ​ = V string ​ + V annulus ​

Pump Displacement and Stroke Calculations

Triplex mud pumps deliver a fixed volume of fluid per mechanical stroke. Pump displacement output ( V stk V_{\text{stk}} V stk ​ ) depends on liner diameter ( D liner D_{\text{liner}} D liner ​ ), stroke length ( L stroke L_{\text{stroke}} L stroke ​ ), and volumetric efficiency ( η vol \eta_{\text{vol}} η vol ​ , typically 95%–98%):

V stk = 0.000243 × D liner 2 × L stroke × η vol [ bbl/stk ] V_{\text{stk}} = 0.000243 \times D_{\text{liner}}^2 \times L_{\text{stroke}} \times \eta_{\text{vol}}\quad [\text{bbl/stk}] V stk ​ = 0.000243 × D liner 2 ​ × L stroke ​ × η vol ​ [ bbl/stk ]

Converting barrel capacities into pump stroke counts establishes the operational timing for kill operations:

Strokes to Bit (Surface to Bit): Number of pump strokes required to pump fluid from surface mud pumps through the drill string to the bit nozzles: Strokes to Bit = V string V stk \text{Strokes to Bit} = \frac{V_{\text{string}}}{V_{\text{stk}}} Strokes to Bit = V stk ​ V string ​ ​

Strokes Bit to Shoe: Number of strokes required to circulate fluid from the bit up to the casing shoe: Strokes Bit to Shoe = V OH V stk \text{Strokes Bit to Shoe} = \frac{V_{\text{OH}}}{V_{\text{stk}}} Strokes Bit to Shoe = V stk ​ V OH ​ ​

Strokes Bit to Surface (Total Annular Strokes): Strokes required to circulate fluid from the bit to the surface flowline: Strokes Bit to Surface = V annulus V stk \text{Strokes Bit to Surface} = \frac{V_{\text{annulus}}}{V_{\text{stk}}} Strokes Bit to Surface = V stk ​ V annulus ​ ​

Total Well System Circulation Strokes: Total Strokes = Strokes to Bit + Strokes Bit to Surface \text{Total Strokes} = \text{Strokes to Bit} + \text{Strokes Bit to Surface} Total Strokes = Strokes to Bit + Strokes Bit to Surface

Circulation Time: Operating time required to complete each circulation phase at a designated kill speed: Time (minutes) = Stroke Count Kill Rate (SPM) \text{Time (minutes)} = \frac{\text{Stroke Count}}{\text{Kill Rate (SPM)}} Time (minutes) = Kill Rate (SPM) Stroke Count ​

Pre-Recorded Hydraulics: Slow Circulation Rate (SCR) Table

A Slow Circulation Rate (SCR)—also termed Reduced Circulating Pressure (RCP)—is the circulating pressure required to pump mud through the well system at a reduced rate (typically 20 to 40 SPM, or roughly one-third to one-half of normal drilling rate). Reduced pump rates limit friction backpressure on exposed open hole formations, reduce choke erosion, and afford the choke operator sufficient reaction time.

Operational Rules for SCR Recording

Typical rig procedures require SCR pressures to be taken and logged on the kill sheet:

At the beginning of each 12-hour tour (shift).

After any change in mud density, viscosity, or solids content.

Following bit, nozzle, or downhole tool (motor/MWD) replacements.

After drilling significant new footage (e.g., every 500 ft 500\text{ ft} 500 ft / 150 m 150\text{ m} 150 m ).

On each active and standby mud pump.

Through both the normal riser/bell nipple and through the dedicated choke line.

Pump Designation Liner Size Slow Pump Speed Circulating Pressure (Normal Path) Circulating Pressure (via Choke Line)

Triplex Pump #1 6.0 in 6.0\text{ in} 6.0 in 20 SPM 20\text{ SPM} 20 SPM 280 psi 280\text{ psi} 280 psi 330 psi 330\text{ psi} 330 psi

Triplex Pump #1 6.0 in 6.0\text{ in} 6.0 in 30 SPM 30\text{ SPM} 30 SPM 580 psi 580\text{ psi} 580 psi 670 psi 670\text{ psi} 670 psi

Triplex Pump #1 6.0 in 6.0\text{ in} 6.0 in 40 SPM 40\text{ SPM} 40 SPM 990 psi 990\text{ psi} 990 psi 1,120 psi 1{,}120\text{ psi} 1 , 120 psi

Triplex Pump #2 6.0 in 6.0\text{ in} 6.0 in 30 SPM 30\text{ SPM} 30 SPM 590 psi 590\text{ psi} 590 psi 680 psi 680\text{ psi} 680 psi

The table is an example only; real values are measured on the rig.

Important

On subsea rigs the long, narrow choke line adds significant friction compared with circulating up the riser, so SCRs must also be recorded through the choke line; failing to do so underestimates circulating friction during the kill. On surface stacks the choke line is short and its friction is usually small, although some procedures still record both.

Pre-Recorded Casing Shoe Fracture Data & Initial MAASP

The formation immediately below the casing shoe is normally assumed to be the weakest exposed point in the open hole. After cementing casing and drilling out the shoe track, a Leak-Off Test (LOT) determines the formation fracture breakdown gradient, expressed as an Equivalent Mud Weight (LOT EMW):

LOT EMW = Test MW + Surface Leak-off Pressure 0.052 × Casing Shoe TVD \text{LOT EMW} = \text{Test MW} + \frac{\text{Surface Leak-off Pressure}}{0.052 \times \text{Casing Shoe TVD}} LOT EMW = Test MW + 0.052 × Casing Shoe TVD Surface Leak-off Pressure ​

From this baseline, the initial Maximum Allowable Annular Surface Pressure (MAASP) is calculated:

MAASP = ( LOT EMW − Current MW ) × 0.052 × Casing Shoe TVD \text{MAASP} = (\text{LOT EMW} - \text{Current MW}) \times 0.052 \times \text{Casing Shoe TVD} MAASP = ( LOT EMW − Current MW ) × 0.052 × Casing Shoe TVD

Warning

Initial MAASP is valid only for the current mud weight . Whenever mud weight is increased, the hydrostatic pressure exerted by the mud column inside the casing increases, leaving less margin for surface backpressure before shoe breakdown occurs. Overlooking this adjustment during a kill operation risks fracturing the formation at the shoe, inducing an underground blowout.

Loading diagram... Kill Sheet Volumetric and Stroke Data Flowchart