Study guide
2.3 Formation Integrity Testing (FIT, LOT) & MAASP
IWCF Level 2 Drilling Well Control Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Well Control Introduction, Pressure Fundamentals & Well Barriers
1.1 Principles of Well Control & Incident Impact 1.2 Hydrostatic Pressure, Formation Pressure & Pressure Gradients 1.3 Well Barrier Philosophy & Barrier Management
2 Chapter 2: Rig Hydraulics, Circulating System & Formation Strength
2.1 Circulating System & Annular Friction Losses 2.2 Equivalent Circulating Density (ECD) & Slow Circulation Rates (SCR) 2.3 Formation Integrity Testing (FIT, LOT) & MAASP
3 Chapter 3: Causes of Kicks & Tripping Mechanics
3.1 Primary Causes of Well Influxes 3.2 Swabbing and Surging Dynamics 3.3 Tripping Operations & Trip Tank Monitoring
4 Chapter 4: Kick Detection & Warning Signs
4.1 Positive Kick Indicators 4.2 Warning Signs of an Impending Kick 4.3 Shallow Gas Hazards & Diverter Operations
5 Chapter 5: Influx Behavior, Shut-In Procedures & Pressures
5.1 Influx Behavior & Gas Migration 5.2 Shut-In Procedures for Drilling, Tripping & Out of Hole 5.3 Shut-In Drill Pipe Pressure (SIDPP), Shut-In Casing Pressure (SICP) & Pit Gain
6 Chapter 6: Kill Sheet Calculations & Well Control Methods
6.1 Kill Sheet Fundamentals & Pre-Recorded Data 6.2 Kill Mud Weight, ICP & FCP Calculations 6.3 Well Control Methods: Driller's, Wait and Weight & Volumetric
7 Chapter 7: Well Control During Casing & Cementing
7.1 Running & Pulling Casing and Liner: Swab, Surge, Returns & Shut-In 7.2 Cementing Casing and Liner: BHP Changes, Verification & Flow During Cementing
8 Chapter 8: Blowout Preventers (BOPs) & Stack Arrangements
8.1 Ram-Type Blowout Preventers 8.2 Annular Blowout Preventers 8.3 BOP Stack Configurations & Drilling Spools
9 Chapter 9: Choke Manifolds, Auxiliary Equipment & Control Systems
9.1 Choke Manifolds, Chokes & Flow Routing 9.2 Internal Blowout Preventers & Auxiliary Equipment 9.3 BOP Hydraulic Control Systems (Closing Units)
10 Chapter 10: Testing, Maintenance & Subsea Systems
10.1 BOP Pressure Testing & Function Testing 10.2 Well Control Drills & Operational Risk Management 10.3 Subsea Well Control Equipment Overview
2.3 Formation Integrity Testing (FIT, LOT) & MAASP
Key Takeaways Explain This Topic AI
A Leak-Off Test (LOT) pumps fluid into the formation until pressure departs from linearity, determining actual rock fracture initiation pressure and fracture gradient.
A Formation Integrity Test (FIT) is a go/no-go test pumped to a pre-agreed design limit without fracturing the rock, verifying shoe competence in development wells.
Equivalent Mud Weight (EMW) reflects the total pressure resistance of the rock at the casing shoe expressed as fluid density: EMW = Test MW + Surface Leak-off Pressure 0.052 × Shoe TVD \text{EMW} = \text{Test MW} + \frac{\text{Surface Leak-off Pressure}}{0.052 \times \text{Shoe TVD}} EMW = Test MW + 0.052 × Shoe TVD Surface Leak-off Pressure .
Maximum Allowable Annular Surface Pressure (MAASP) is the maximum surface casing pressure permitted before fracturing the formation at the casing shoe: MAASP = ( EMW − Current MW ) × 0.052 × Shoe TVD \text{MAASP} = (\text{EMW} - \text{Current MW}) \times 0.052 \times \text{Shoe TVD} MAASP = ( EMW − Current MW ) × 0.052 × Shoe TVD .
Raising drilling mud weight directly reduces MAASP because the heavier mud column exerts greater hydrostatic pressure on the casing shoe; furthermore, MAASP becomes invalid once gas enters the casing.
Last updated: October 2026
When drilling proceeds out of a casing shoe into a new hole section, the formation immediately below the shoe represents the geomechanical weak link of the open-hole wellbore. Because overburden stress and rock compaction increase with depth, shallower formations have lower fracture resistance than deeper rocks. If wellbore pressures become excessive during drilling, circulation, or well shut-in, rock failure will almost invariably initiate at the casing shoe. Accurately testing the mechanical strength of the casing shoe formation and establishing the Maximum Allowable Annular Surface Pressure (MAASP) are vital engineering safeguards in well control.
The Critical Role of the Casing Shoe
After cementing casing, drilling crews drill through the shoe track, cleaning out 5 to 15 feet (1.5 to 5 meters) of new formation. At this point, the well is shut in and tested to confirm two parameters:
Cement Seal Integrity: Ensuring no micro-annular channels exist between casing steel, cement sheath, and rock that could allow fluid communication behind casing.
Formation Fracture Strength: Determining the maximum hydraulic pressure that exposed rock immediately beneath the shoe can withstand before fracturing.
Leak-Off Test (LOT) vs. Formation Integrity Test (FIT)
Industry practice employs two distinct testing methodologies:
Parameter Leak-Off Test (LOT) Formation Integrity Test (FIT)
Primary Objective Determine actual fracture breakdown pressure of the formation Confirm the formation can withstand a predetermined pressure limit without fracturing
Pumping End Point Pumped until the pressure-volume curve departs from linearity (fluid enters micro-fissures) Pumped to a predetermined target test pressure; held for 10–15 minutes
Risk of Formation Damage Slight risk of creating permanent micro-fissures at the casing shoe Low risk, because the test stops below the fracture pressure
Typical Application Exploratory (wildcat) wells, appraisal drilling, unknown geomechanical basins Development wells, mature fields with known fracture trends, depleted or fault-sensitive zones
Calculated Output Actual Fracture Gradient ( F G FG FG ) and actual maximum Equivalent Mud Weight ( EMW \text{EMW} EMW ) Proven lower-bound Equivalent Mud Weight ( EMW safe \text{EMW}_{\text{safe}} EMW safe )
The Leak-Off Test (LOT) Profile
An LOT uses a high-pressure cementing unit pumping mud at 0.25 to 0.50 bpm into the closed wellbore while plotting surface pressure versus cumulative volume:
Elastic Compression: Mud compresses and casing expands elastically. Surface pressure rises in a straight line with volume.
Leak-Off Point (LOP): The inflection where the curve deviates from the straight line, signifying rock tensile failure and micro-fracture initiation.
Pump Shutdown & Bleed-Off: Pumping stops immediately at LOP. Stabilized shut-in pressure is recorded, and volume is bled back to confirm recovery.
The Formation Integrity Test (FIT)
In an FIT, operators avoid stressing rock to failure. Pumping proceeds slowly to a predetermined target test pressure calculated from the maximum mud weight planned for the section plus a safety margin. Pressure is held for 10 to 15 minutes; if no drop occurs, the shoe is certified for drilling.
Calculation of Fracture Gradient and Equivalent Mud Weight (EMW)
The surface leak-off pressure ( P lot P_{\text{lot}} P lot ) recorded during an LOT is converted into downhole formation fracture strength:
Equivalent Mud Weight (EMW) Formula
IWCF's formula sheet calls this result the maximum allowable fluid density .
EMW = Test MW + P lot 0.052 × Shoe TVD \text{EMW} = \text{Test MW} + \frac{P_{\text{lot}}}{0.052 \times \text{Shoe TVD}} EMW = Test MW + 0.052 × Shoe TVD P lot
Where EMW \text{EMW} EMW and Test MW \text{Test MW} Test MW are in ppg, P lot P_{\text{lot}} P lot is surface leak-off pressure in psi, and Shoe TVD \text{Shoe TVD} Shoe TVD is in feet ( 0.052 0.052 0.052 conversion factor).
Downhole Formation Fracture Pressure ( P frac P_{\text{frac}} P frac ) & Fracture Gradient ( F G FG FG )
P frac = P lot + ( 0.052 × Test MW × Shoe TVD ) = 0.052 × EMW × Shoe TVD P_{\text{frac}} = P_{\text{lot}} + (0.052 \times \text{Test MW} \times \text{Shoe TVD}) = 0.052 \times \text{EMW} \times \text{Shoe TVD} P frac = P lot + ( 0.052 × Test MW × Shoe TVD ) = 0.052 × EMW × Shoe TVD
F G = P frac Shoe TVD = 0.052 × EMW ( in psi/ft ) FG = \frac{P_{\text{frac}}}{\text{Shoe TVD}} = 0.052 \times \text{EMW} \quad (\text{in psi/ft}) FG = Shoe TVD P frac = 0.052 × EMW ( in psi/ft )
Calculation Example
A casing shoe is at 8,000 ft TVD. An LOT conducted with 10.0 ppg mud exhibits leak-off at 1,040 psi surface pressure:
EMW = 10.0 + 1,040 0.052 × 8,000 = 10.0 + 1,040 416 = 10.0 + 2.50 = 12.50 ppg \text{EMW} = 10.0 + \frac{1{,}040}{0.052 \times 8{,}000} = 10.0 + \frac{1{,}040}{416} = 10.0 + 2.50 = 12.50\text{ ppg} EMW = 10.0 + 0.052 × 8 , 000 1 , 040 = 10.0 + 416 1 , 040 = 10.0 + 2.50 = 12.50 ppg
P frac = 0.052 × 12.50 × 8,000 = 5,200 psi P_{\text{frac}} = 0.052 \times 12.50 \times 8{,}000 = 5{,}200\text{ psi} P frac = 0.052 × 12.50 × 8 , 000 = 5 , 200 psi
F G = 5,200 psi 8,000 ft = 0.650 psi/ft FG = \frac{5{,}200\text{ psi}}{8{,}000\text{ ft}} = 0.650\text{ psi/ft} FG = 8 , 000 ft 5 , 200 psi = 0.650 psi/ft
Maximum Allowable Annular Surface Pressure (MAASP)
MAASP is the highest permissible surface pressure on the casing gauge before the formation at the shoe fractures, assuming the casing column from surface to shoe is filled with fluid of Current MW:
MAASP = ( EMW − Current MW ) × 0.052 × Shoe TVD = P frac − H P shoe, current \text{MAASP} = (\text{EMW} - \text{Current MW}) \times 0.052 \times \text{Shoe TVD} = P_{\text{frac}} - HP_{\text{shoe, current}} MAASP = ( EMW − Current MW ) × 0.052 × Shoe TVD = P frac − H P shoe, current
Dynamic Impact of Mud Weight Changes on MAASP
Because downhole fracture pressure ( P frac P_{\text{frac}} P frac ) is fixed, increasing drilling mud weight increases hydrostatic head inside casing, leaving less allowable surface pressure before the shoe fractures:
Warning
As drilling mud weight increases, MAASP decreases! Whenever mud weight is increased in the pits, MAASP must be recalculated immediately.
Using our previous example ( EMW = 12.50 ppg \text{EMW} = 12.50\text{ ppg} EMW = 12.50 ppg , Shoe TVD = 8,000 ft \text{Shoe TVD} = 8{,}000\text{ ft} Shoe TVD = 8 , 000 ft ):
With 10.0 ppg mud: MAASP = ( 12.50 − 10.0 ) × 416 = 1,040 psi \text{MAASP} = (12.50 - 10.0) \times 416 = 1{,}040\text{ psi} MAASP = ( 12.50 − 10.0 ) × 416 = 1 , 040 psi
With 11.2 ppg mud: MAASP = ( 12.50 − 11.2 ) × 416 = 540.8 psi \text{MAASP} = (12.50 - 11.2) \times 416 = 540.8\text{ psi} MAASP = ( 12.50 − 11.2 ) × 416 = 540.8 psi Raising mud weight by 1.2 ppg reduces surface safety margin from 1,040 psi to 541 psi.
Critical Operational Limitations of MAASP During Well Kicks
Blindly adhering to MAASP when gas is in the wellbore is a dangerous well control trap.
The Core Assumption of MAASP
MAASP strictly assumes the annulus between surface and casing shoe is completely filled with a continuous, uniform column of drilling mud at Current MW.
Influx Migration Across the Shoe
Gas Below the Shoe: When an influx is below the shoe, the casing remains 100% full of mud. MAASP is valid. If shut-in casing pressure ( S I C P SICP S I CP ) reaches MAASP, the shoe is at immediate risk of fracturing.
Gas Above the Shoe (Inside Casing): As gas migrates into casing and expands, low-density gas ( 0.1 0.1 0.1 to 0.2 psi/ft 0.2\text{ psi/ft} 0.2 psi/ft ) displaces high-density mud ( 0.5 0.5 0.5 to 0.8 psi/ft 0.8\text{ psi/ft} 0.8 psi/ft ), drastically reducing hydrostatic head above the shoe. Surface casing pressure can rise well above calculated MAASP without exceeding shoe fracture pressure.
Important
If a choke operator panics because casing pressure exceeds MAASP and opens the choke while gas is inside casing, bottom-hole pressure drops below pore pressure, triggering massive additional influx. Once gas enters the casing, MAASP is no longer valid; choke adjustments must follow drill pipe pressure on the kill sheet.