Study guide

Well Control Drills and Operational Checklists

IWCF Level 3 Drilling Well Control Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview

Well Control Incidents and Their Consequences Qualification, Assessment and Study Planning

2 Hydrostatic Pressure and the Circulating System

Hydrostatic Pressure, Fluid Gradients, and Mud Weight Multiple Fluid Columns and Inverse Hydrostatic Calculations U-Tube Principle, Dynamic Pressure Losses, and Equivalent Circulating Density

3 Formation Pressure and Integrity Limits

Formation Pore Pressure, Normal vs Abnormal Pressure, and Fracture Gradient LOT/FIT Graphs and the Pressure Window MAASP, Kick Tolerance, and Formation Breakdown

4 Barriers and Risk Management

Well Barrier Concepts: Primary, Secondary, and Composite Envelopes Barrier Verification, Monitoring, and Life Cycle Management Well Control Risk Assessment, Human Factors, and Management of Change

5 Fluid Density and Circulation Data

Insufficient Mud Density & Encountering Abnormal Pressures Barite Weighting and Pump-Pressure Changes Pre-Recorded Data, Pump Output, and Slow Circulating Rates

6 Trip Preparation and Pressure Support

Swabbing and Surging During Tripping Operations Slugs, Trip Margin and Pumping Out Unfilled-Hole Limits and Tubular Displacement

7 Trip Monitoring and Connections

Hole Fill Failure and Trip Tank Monitoring Procedures Trip Tanks, PVT Systems, and Flow Return Sensors Kick Indicators During Tripping, Connections, and Out of Hole

8 Kick Warnings and Indicators

Flow Checks and Drilling Breaks Primary Kick Indicators While Drilling Lost Circulation and Loss of Hydrostatic Head

9 Influx Characteristics and Behaviour

Influx Types (Gas, Oil, Salt Water) & Influx Density Determination Gas Solubility in Oil-Based Mud vs Water-Based Mud

10 Gas Expansion and Closed-Well Migration

Gas Physics: Boyle's Law, Expansion, and Migration Velocities Gas Migration in a Shut-In Well & Pressure Buildup Effects

11 Surface Shut-In and Pressure Interpretation

Hard Shut-In vs Soft Shut-In Philosophies & Principles Surface BOP Shut-In Protocols (Drilling, Tripping, Wireline/Out of Hole) Post Shut-In Pressure Stabilization & Data Recording

12 Subsea, Wireline and Stripping Response

Subsea BOP Shut-In Protocols & Space-Out Procedures Wireline Displacement and Pressure-Control Equipment Annular and Ram-to-Ram Stripping

13 Kill-Sheet Calculations

Calculating Kill Mud Weight, ICP, and FCP Drill String/Annular Volumes, Strokes to Bit, and Circulating Times

14 Circulating Kill Methods

The Driller's Method: Detailed Two-Circulation Procedure The Wait and Weight Method & Step-Down Pressure Graphs Comparison of Constant Bottomhole Pressure Methods

15 Special Pressure-Control Methods

Volumetric Method, Lubricate and Bleed, and Bullheading Subsea CLF: Startup, Shutdown and Fluid Displacement

16 Casing and Cementing Well Control

Running Casing: Floats, Clearances and Volumes Cementing: Pressure Profile and Barrier Quality Casing Shut-In and Assembly Readiness

17 Drills and Equipment First Actions

Well Control Drills and Operational Checklists Gauge Failure and BOP Leak First Actions Bit Nozzle Plugging and Mud Pump Failure During a Kill

18 Operational Contingencies

Drill String Washout and Parted Pipe Management Severe Lost Circulation and Underground Blowout Scenarios Gas at Surface, Hydrate Formation, and Diverter Operations

19 Preventer Capabilities

Annular Preventers: Design, Operation, and Stripping Use Pipe Rams and Variable Bore Rams (VBRs) Blind Rams, Shear Rams, and Casing Shear Rams

20 Stack, Connections and Flow Routes

Surface BOP Stack Arrangements, API Specifications, and Outlets Ram Locking Mechanisms and Wellhead Connectors Choke and Kill Lines, Valves, and Pressure Ratings Choke Manifolds, Remote Chokes, and Manual Adjustable Chokes

21 Diverters and Auxiliary Equipment

Shallow Gas and Diverter Response Mud/Gas Separators (Poor Boy Degassers): Liquid Seal & Blow-Through Vacuum Degassers, Desanders, Desilters, and Rig Gas Detectors Drill String Safety Valves, Gray Valves, and Float Valves

22 Hydraulic Control Systems

Accumulator Unit Components: Reservoir, Fluid, and Pumps Accumulator Bottles, Nitrogen Precharge, and Operating Pressures Regulators, Pilot Circuits, and Manifold/Annular Pressure Control Stored Capacity, Accumulator Drawdown Tests and Remote Panels

23 Testing and Subsea Systems

Low-Pressure and High-Pressure BOP Testing Criteria Function Testing, Test Frequencies, and Test Tools Subsea BOP Architecture, LMRP, MUX Control, and Choke Line Friction Subsea Riser Margin, Gas in Riser, and Emergency Disconnect

Well Control Drills and Operational Checklists

Key Takeaways Explain This Topic AI

Drills maintain competence and test readiness for the actual operation and equipment.

Checklists must verify equipment and procedures, including non-shearable and non-sealable items.

Unexpected pressure reductions and falling returns can indicate weak-point losses.

Drawdown tests use the specified sequence and minimum operating pressure, with recorded results.

Last updated: October 2026

Readiness must be demonstrated

Well control drills develop and maintain crew competence and check that the required equipment is ready. The syllabus includes pit, trip, strip, choke and diverter drills and an accumulator test. These activities have different purposes: recognising a gain, responding during a trip, managing pipe through barriers, controlling pressure, diverting shallow gas and demonstrating stored hydraulic capacity. A drill should test its intended skill without creating an unplanned well control hazard.

The applicable operations manual, well programme and standards define the schedule, permitted simulation and acceptance criteria. A syllabus reference to an API standard is not itself a universal interval or permission to actuate equipment on unsuitable tubulars. Brief the exercise, identify the current barrier configuration and establish stop conditions. Separate simulated indications from real ones so a genuine event is never dismissed as part of the drill.

Use a checklist to verify critical dependencies

A useful checklist confirms both equipment and procedure. Equipment checks include the correct BOP elements, available control pressure, valves and flow routes, pressure gauges, trip tank, pit and flow monitoring, internal safety valves, crossovers and communications. Procedure checks include the current space-out reference, response sequence, responsible roles, weak-point limit and emergency alternatives. A tick beside “BOP ready” is too vague if the crew has not checked what can actually seal today's assembly.

Before a non-shearable or non-sealable item crosses the BOP, identify it and its planned position, perform the required flow check and establish a means of well closure. A qualified ram may seal the pipe body but not the adjacent tool joint. A shear ram may cut one grade and weight of pipe but not another. The checklist must refer to the current capability data and assembly tally. If the planned movement removes the available closure option, use the approved risk and change process before proceeding.

Pit and trip drills

A pit drill tests recognition of a specified gain or increased returns and the correct communication and response. The driller should identify the deviation, suspend the relevant operation, use the instructed shut-in sequence and verify the simulated or actual barrier function. The observer records detection and response, but speed alone is not success if the wrong function is selected or a flow path remains open.

A trip drill starts with the correct displacement baseline. The crew compares expected fill or returns with the simulated actual result, stops movement, communicates and evaluates flow as instructed. It checks that the safety valve and crossover are available for the string in use and that the current tubular can be sealed. A drill that uses drillpipe assumptions while casing is at the BOP tests the wrong readiness.

Strip, choke and diverter drills

A strip drill tests barrier transfer, space-out, displacement measurement and pressure control using a safe approved arrangement. Ram-to-ram practice should include chamber equalisation and verification of the receiving barrier. A choke drill tests pump-and-choke coordination through startup, a rate change and shutdown. Record whether the operator maintains the instructed pressure while recognising deviations rather than simply following a memorised choke position.

A diverter drill checks that the vent route is available before the packing element seals, that the correct outlet is selected and that interlocks work as designed. It also tests communication, fluid-supply preparation and monitoring for leaks or erosion. On a floating rig, include the relevant riser and marine coordination duties. Function feedback alone does not prove that an obstructed vent will pass the required flow.

Recognise a weak-point limit being exceeded

MAASP is tied to an assumed fluid profile and weak point. During a kill, influx and fluid positions change that relationship. The crew must know the approved dynamic limits and compare predicted pressures and volumes with actual readings. A decrease in returns, unexpected annulus-pressure decline followed by a drillpipe-pressure decline, or unplanned extra choke closure needed to maintain drillpipe pressure can indicate losses. These observations require immediate communication and the contingency response.

Do not infer that a lower casing pressure always means improved safety. If fluid is being lost through a weak formation, pressure can fall while the well becomes less controlled. Conversely, gas above the weak point may change the permissible surface pressure from the original mud-only value. A drill should ask the candidate to explain the pressure at the weak point and the volume balance, not merely compare one gauge with yesterday's number.

Accumulator tests and learning records

An accumulator drawdown test checks the stored fluid and pressure available for the specified function sequence with the recharge pumps isolated as instructed. Record starting and ending pressure, function times and volumes, and compare with the applicable minimum pressure and sequence criteria. A final pressure above a generic number is inadequate if a required ram needs more pressure to close against the anticipated well pressure.

After any drill, record the scenario, equipment configuration, observed actions, deficiencies and corrective actions. Verify that the equipment and valve line-up are restored to the intended operating state. Changes to a well control procedure require the appropriate Management of Change review. A productive debrief identifies a concrete improvement—such as a missing crossover, misunderstood gauge or unclear call—then confirms the improvement in a later authorised exercise.

Drill purposes

  • Item Interpretation
  • Pit and trip Recognition and appropriate initial response
  • Strip and choke Barrier transfer and coordinated pressure/volume control
  • Diverter Available outlet, sequence and communication
  • Accumulator Specified stored-energy sequence and minimum state