Study guide

Function Testing, Test Frequencies, and Test Tools

IWCF Level 3 Drilling Well Control Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview

Well Control Incidents and Their Consequences Qualification, Assessment and Study Planning

2 Hydrostatic Pressure and the Circulating System

Hydrostatic Pressure, Fluid Gradients, and Mud Weight Multiple Fluid Columns and Inverse Hydrostatic Calculations U-Tube Principle, Dynamic Pressure Losses, and Equivalent Circulating Density

3 Formation Pressure and Integrity Limits

Formation Pore Pressure, Normal vs Abnormal Pressure, and Fracture Gradient LOT/FIT Graphs and the Pressure Window MAASP, Kick Tolerance, and Formation Breakdown

4 Barriers and Risk Management

Well Barrier Concepts: Primary, Secondary, and Composite Envelopes Barrier Verification, Monitoring, and Life Cycle Management Well Control Risk Assessment, Human Factors, and Management of Change

5 Fluid Density and Circulation Data

Insufficient Mud Density & Encountering Abnormal Pressures Barite Weighting and Pump-Pressure Changes Pre-Recorded Data, Pump Output, and Slow Circulating Rates

6 Trip Preparation and Pressure Support

Swabbing and Surging During Tripping Operations Slugs, Trip Margin and Pumping Out Unfilled-Hole Limits and Tubular Displacement

7 Trip Monitoring and Connections

Hole Fill Failure and Trip Tank Monitoring Procedures Trip Tanks, PVT Systems, and Flow Return Sensors Kick Indicators During Tripping, Connections, and Out of Hole

8 Kick Warnings and Indicators

Flow Checks and Drilling Breaks Primary Kick Indicators While Drilling Lost Circulation and Loss of Hydrostatic Head

9 Influx Characteristics and Behaviour

Influx Types (Gas, Oil, Salt Water) & Influx Density Determination Gas Solubility in Oil-Based Mud vs Water-Based Mud

10 Gas Expansion and Closed-Well Migration

Gas Physics: Boyle's Law, Expansion, and Migration Velocities Gas Migration in a Shut-In Well & Pressure Buildup Effects

11 Surface Shut-In and Pressure Interpretation

Hard Shut-In vs Soft Shut-In Philosophies & Principles Surface BOP Shut-In Protocols (Drilling, Tripping, Wireline/Out of Hole) Post Shut-In Pressure Stabilization & Data Recording

12 Subsea, Wireline and Stripping Response

Subsea BOP Shut-In Protocols & Space-Out Procedures Wireline Displacement and Pressure-Control Equipment Annular and Ram-to-Ram Stripping

13 Kill-Sheet Calculations

Calculating Kill Mud Weight, ICP, and FCP Drill String/Annular Volumes, Strokes to Bit, and Circulating Times

14 Circulating Kill Methods

The Driller's Method: Detailed Two-Circulation Procedure The Wait and Weight Method & Step-Down Pressure Graphs Comparison of Constant Bottomhole Pressure Methods

15 Special Pressure-Control Methods

Volumetric Method, Lubricate and Bleed, and Bullheading Subsea CLF: Startup, Shutdown and Fluid Displacement

16 Casing and Cementing Well Control

Running Casing: Floats, Clearances and Volumes Cementing: Pressure Profile and Barrier Quality Casing Shut-In and Assembly Readiness

17 Drills and Equipment First Actions

Well Control Drills and Operational Checklists Gauge Failure and BOP Leak First Actions Bit Nozzle Plugging and Mud Pump Failure During a Kill

18 Operational Contingencies

Drill String Washout and Parted Pipe Management Severe Lost Circulation and Underground Blowout Scenarios Gas at Surface, Hydrate Formation, and Diverter Operations

19 Preventer Capabilities

Annular Preventers: Design, Operation, and Stripping Use Pipe Rams and Variable Bore Rams (VBRs) Blind Rams, Shear Rams, and Casing Shear Rams

20 Stack, Connections and Flow Routes

Surface BOP Stack Arrangements, API Specifications, and Outlets Ram Locking Mechanisms and Wellhead Connectors Choke and Kill Lines, Valves, and Pressure Ratings Choke Manifolds, Remote Chokes, and Manual Adjustable Chokes

21 Diverters and Auxiliary Equipment

Shallow Gas and Diverter Response Mud/Gas Separators (Poor Boy Degassers): Liquid Seal & Blow-Through Vacuum Degassers, Desanders, Desilters, and Rig Gas Detectors Drill String Safety Valves, Gray Valves, and Float Valves

22 Hydraulic Control Systems

Accumulator Unit Components: Reservoir, Fluid, and Pumps Accumulator Bottles, Nitrogen Precharge, and Operating Pressures Regulators, Pilot Circuits, and Manifold/Annular Pressure Control Stored Capacity, Accumulator Drawdown Tests and Remote Panels

23 Testing and Subsea Systems

Low-Pressure and High-Pressure BOP Testing Criteria Function Testing, Test Frequencies, and Test Tools Subsea BOP Architecture, LMRP, MUX Control, and Choke Line Friction Subsea Riser Margin, Gas in Riser, and Emergency Disconnect

Function Testing, Test Frequencies, and Test Tools

Key Takeaways Explain This Topic AI

Function tests use actual operating, timing and configuration criteria.

Test schedules and safe actuation conditions are programme-specific.

Test tools, casing and supports must satisfy pressure and force limits.

Diverter verification checks both sequence and the available flow route.

Last updated: October 2026

A function test asks whether equipment operates

Function testing checks movement, response time, operating pressure, fluid use and the intended sequence. The syllabus includes testing before installation, on installation and during well operations. The actual schedule and conditions come from the operations manual and applicable requirements. Do not infer one universal weekly or fourteen-day rule from a training example.

Tests must suit the current assembly and barrier state. A blind or shear function cannot be actuated onto an unqualified item merely because a calendar interval has arrived. Confirm pipe and tool position, test prerequisites and alternate containment. Distinguish an actual function from a simulation and record which was performed. The test is successful only when its defined acceptance criteria are met.

Use supplied closing data

A training table may give a specific annular model a maximum closing time of 45 seconds and a qualified ram model 30 seconds under stated conditions. A 40-second annular result satisfies that time limit; a 35-second ram result does not. This is a supplied-data exercise, not a universal limit by bore diameter. Pressure, fluid, configuration and measurement start/finish points must match the criteria.

A command timestamp and a panel lamp can differ from full actuator travel. Record the actual method used to establish completion. The relevant hydraulic pressure and fluid-volume response support the result. A fast selector movement with no actuator response fails the intended test even if the command arrived immediately.

Pressure test tools have their own ratings

A test plug can isolate a pressure-test boundary from the casing or formation only in its qualified arrangement. Check its sealing direction, location, landing, pressure rating, load capacity and the monitored lower side. The test can impose substantial axial force on a plug. At 5,000 psi across a supplied effective area of 20 in², theoretical force is 100,000 lb. The tool and support arrangement must be qualified for the actual load and conditions.

A cup tester relies on a different seal and often exposes casing to test pressure. The permitted pressure considers the cup/tool rating and the approved casing integrity limit, including service and wear—not nominal casing burst alone. A test plug's isolation cannot be assumed just because it was lowered to a given depth. Verify it as the procedure directs.

Accessories can change the boundary

Wear bushings, running tools and temporary assemblies may block ports, prevent sealing or affect the test-tool landing. Their removal or positioning depends on the qualified test arrangement. Do not state that every wear bushing must always be retrieved for every possible test. Read the drawing and procedure, identify what is exposed and confirm pressure reaches the intended component.

Test strings, valves, hoses and gauges must have suitable ratings and connections. A lower-rated adapter can become the binding limit. Instrument range should permit a meaningful reading of both low and high stages as required. If separate gauges are used, identify the communicating taps and calibration records. An isolated gauge does not provide a valid test result.

Diverter function and flow verification

A diverter test checks the open outlet, packing-element operation, valve sequence and interlocks against the actual layout. Flow or venting verification demonstrates that the selected route is unobstructed. Test direction, volume, instrumentation and fluid follow the specified criteria. Function feedback does not alone prove an eroded or blocked vent can pass the required flow.

The test must not create a closed pressure system beyond the diverter's limits. Confirm the vent path before sealing the upward route, observe the selected destination and monitor for leaks. Record whether both the control sequence and flow route passed. Restore the top-hole operating line-up and communicate any limitation before entering the shallow-gas interval.

Failure and return to service

Slow or incomplete movement can reflect inadequate supply, air in a circuit, leakage, obstruction, regulator problems or actuator failure. Secure the well using the available qualified barrier and inform the supervisor. Repair under controlled isolation, then repeat the relevant function and pressure verification. A pressure test cannot excuse a function that fails to operate when needed.

Keep the equipment identity, configuration, pressure, time, volume, observations, result and approval. A meaningful handover states which functions are tested, inhibited or unresolved and which alternatives remain available. This connects maintenance evidence to the operator's response capability, rather than presenting a calendar checkmark as proof that every BOP and valve is ready.

Supplied function limits

  • Item Interpretation
  • Annular 45 second limit, actual 40 Meets the supplied timing criterion
  • Ram 30 second limit, actual 35 Fails the supplied timing criterion
  • 20 in² at 5,000 psi 100,000 lb theoretical test-tool force
  • Diverter Verify sequence and actual vent flow path