Study guide

Swabbing and Surging During Tripping Operations

IWCF Level 3 Drilling Well Control Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview

Well Control Incidents and Their Consequences Qualification, Assessment and Study Planning

2 Hydrostatic Pressure and the Circulating System

Hydrostatic Pressure, Fluid Gradients, and Mud Weight Multiple Fluid Columns and Inverse Hydrostatic Calculations U-Tube Principle, Dynamic Pressure Losses, and Equivalent Circulating Density

3 Formation Pressure and Integrity Limits

Formation Pore Pressure, Normal vs Abnormal Pressure, and Fracture Gradient LOT/FIT Graphs and the Pressure Window MAASP, Kick Tolerance, and Formation Breakdown

4 Barriers and Risk Management

Well Barrier Concepts: Primary, Secondary, and Composite Envelopes Barrier Verification, Monitoring, and Life Cycle Management Well Control Risk Assessment, Human Factors, and Management of Change

5 Fluid Density and Circulation Data

Insufficient Mud Density & Encountering Abnormal Pressures Barite Weighting and Pump-Pressure Changes Pre-Recorded Data, Pump Output, and Slow Circulating Rates

6 Trip Preparation and Pressure Support

Swabbing and Surging During Tripping Operations Slugs, Trip Margin and Pumping Out Unfilled-Hole Limits and Tubular Displacement

7 Trip Monitoring and Connections

Hole Fill Failure and Trip Tank Monitoring Procedures Trip Tanks, PVT Systems, and Flow Return Sensors Kick Indicators During Tripping, Connections, and Out of Hole

8 Kick Warnings and Indicators

Flow Checks and Drilling Breaks Primary Kick Indicators While Drilling Lost Circulation and Loss of Hydrostatic Head

9 Influx Characteristics and Behaviour

Influx Types (Gas, Oil, Salt Water) & Influx Density Determination Gas Solubility in Oil-Based Mud vs Water-Based Mud

10 Gas Expansion and Closed-Well Migration

Gas Physics: Boyle's Law, Expansion, and Migration Velocities Gas Migration in a Shut-In Well & Pressure Buildup Effects

11 Surface Shut-In and Pressure Interpretation

Hard Shut-In vs Soft Shut-In Philosophies & Principles Surface BOP Shut-In Protocols (Drilling, Tripping, Wireline/Out of Hole) Post Shut-In Pressure Stabilization & Data Recording

12 Subsea, Wireline and Stripping Response

Subsea BOP Shut-In Protocols & Space-Out Procedures Wireline Displacement and Pressure-Control Equipment Annular and Ram-to-Ram Stripping

13 Kill-Sheet Calculations

Calculating Kill Mud Weight, ICP, and FCP Drill String/Annular Volumes, Strokes to Bit, and Circulating Times

14 Circulating Kill Methods

The Driller's Method: Detailed Two-Circulation Procedure The Wait and Weight Method & Step-Down Pressure Graphs Comparison of Constant Bottomhole Pressure Methods

15 Special Pressure-Control Methods

Volumetric Method, Lubricate and Bleed, and Bullheading Subsea CLF: Startup, Shutdown and Fluid Displacement

16 Casing and Cementing Well Control

Running Casing: Floats, Clearances and Volumes Cementing: Pressure Profile and Barrier Quality Casing Shut-In and Assembly Readiness

17 Drills and Equipment First Actions

Well Control Drills and Operational Checklists Gauge Failure and BOP Leak First Actions Bit Nozzle Plugging and Mud Pump Failure During a Kill

18 Operational Contingencies

Drill String Washout and Parted Pipe Management Severe Lost Circulation and Underground Blowout Scenarios Gas at Surface, Hydrate Formation, and Diverter Operations

19 Preventer Capabilities

Annular Preventers: Design, Operation, and Stripping Use Pipe Rams and Variable Bore Rams (VBRs) Blind Rams, Shear Rams, and Casing Shear Rams

20 Stack, Connections and Flow Routes

Surface BOP Stack Arrangements, API Specifications, and Outlets Ram Locking Mechanisms and Wellhead Connectors Choke and Kill Lines, Valves, and Pressure Ratings Choke Manifolds, Remote Chokes, and Manual Adjustable Chokes

21 Diverters and Auxiliary Equipment

Shallow Gas and Diverter Response Mud/Gas Separators (Poor Boy Degassers): Liquid Seal & Blow-Through Vacuum Degassers, Desanders, Desilters, and Rig Gas Detectors Drill String Safety Valves, Gray Valves, and Float Valves

22 Hydraulic Control Systems

Accumulator Unit Components: Reservoir, Fluid, and Pumps Accumulator Bottles, Nitrogen Precharge, and Operating Pressures Regulators, Pilot Circuits, and Manifold/Annular Pressure Control Stored Capacity, Accumulator Drawdown Tests and Remote Panels

23 Testing and Subsea Systems

Low-Pressure and High-Pressure BOP Testing Criteria Function Testing, Test Frequencies, and Test Tools Subsea BOP Architecture, LMRP, MUX Control, and Choke Line Friction Subsea Riser Margin, Gas in Riser, and Emergency Disconnect

Swabbing and Surging During Tripping Operations

Key Takeaways Explain This Topic AI

Pulling can reduce pressure through swab; running can increase it through surge.

Clearance, measured length, fluid properties, balling and speed affect the response.

Floating-rig motion can add movement-related effects.

Pump-out mitigation needs adequate verified output and support.

Last updated: October 2026

Swabbing and Surging During Tripping Operations

Tripping the drill string—either pulling out of the hole (POOH) or running into the hole (RIH)—can introduce significant dynamic pressure changes in the wellbore. These pressure fluctuations are known as swabbing and surging, and they pose significant risks to primary well control, and require attention to pressure margin as well as pipe-handling tasks.

The Mechanics of Swabbing and Surging

Swabbing is the reduction in bottomhole pressure (BHP) caused by the upward movement of the drill string. As the pipe is pulled, fluid must flow downward through the annular space to fill the void left below the bit. The viscous drag of the fluid moving against the pipe and the wellbore walls creates a frictional pressure loss, reducing the pressure below the moving assembly; the dynamic pressure change is separate from the static hydrostatic head. If the swab pressure exceeds the overbalance margin, formation fluids will be drawn into the wellbore.

Surging is the exact opposite. It is the increase in BHP caused by the downward movement of the drill string. As the pipe is lowered, it displaces fluid, forcing it to flow upward through the annulus at high velocity. This creates a positive frictional pressure, adding to the hydrostatic pressure at the bottom of the hole. Severe surging can easily exceed the formation fracture gradient, leading to induced fractures, severe lost circulation, and the subsequent loss of hydrostatic head.

Physics and the Piston Effect

The severity of swabbing and surging is governed by the 'piston effect,' which depends on several interrelated mechanical and rheological factors evaluated under the Bingham Plastic or Power Law fluid models:

Aggravating Factor Impact on Swabbing/Surging Explanation

Tight Annular Clearance Major Increase Small clearance between the BHA and the hole ID acts as a strict fluid restriction, forcing the assembly to act like a physical plunger.

High Tripping Speed Major Increase Frictional pressure losses can increase nonlinearly with fluid velocity. Faster tripping forces mud to move faster through the restriction, drastically increasing dynamic pressures.

High Yield Point (YP) Moderate Increase A high yield point means the mud has a strong resistance to flow, increasing the frictional drag forces on the drill string.

High Gel Strengths Severe Initial Spike High progressive gel strengths mean the static mud structure requires massive force to break. The initial movement of the pipe creates a massive swab/surge spike before the mud liquefies.

Balled-up BHA Critical Danger Sticky clays packing around the bit and stabilizers effectively seal the annulus, turning the BHA into a solid piston with near-zero fluid bypass.

Calculating Swab and Surge Pressure Loss

During a tripping operation, the effective Bottomhole Pressure while pulling is calculated as: B H P = H P − Δ P swab BHP = HP - \Delta P_{\text{swab}} B H P = H P − Δ P swab ​

During running in hole, the effective Bottomhole Pressure is: B H P = H P + Δ P surge BHP = HP + \Delta P_{\text{surge}} B H P = H P + Δ P surge ​

For example, assume a well has a True Vertical Depth (TVD) of 12,000 ft with a mud weight of 11.5 ppg. The static Hydrostatic Pressure (HP) is: H P = 0.052 × 11.5 × 12 , 000 = 7 , 176 psi HP = 0.052 \times 11.5 \times 12,000 = 7,176 \text{ psi} H P = 0.052 × 11.5 × 12 , 000 = 7 , 176 psi

If advanced dynamic rheology models (such as Bingham-Plastic or Herschel-Bulkley) determine that pulling the BHA at 90 ft/min generates a swab pressure ( Δ P swab \Delta P_{\text{swab}} Δ P swab ​ ) of 350 psi, the effective BHP while pulling becomes: B H P = 7 , 176 − 350 = 6 , 826 psi BHP = 7,176 - 350 = 6,826 \text{ psi} B H P = 7 , 176 − 350 = 6 , 826 psi

If the formation pore pressure at this depth is 7,000 psi, the static mud column is overbalanced by 176 psi. However, during the pipe movement, the effective BHP falls 174 psi below the pore pressure. An exposed permeable formation can supply an influx during this underbalance. Its rate depends on the pressure difference and formation flow characteristics; the calculation does not establish that a fixed influx volume must enter.

Mitigation Practices for Safe Tripping

To prevent swabbing an influx or surging the formation, drillers must employ stringent, mathematically sound mitigation practices:

Condition the hole and mud at the points specified in the programme rather than a universal stand interval. Pumping out can reduce swab risk only if verified output fills the increasing space below the bit and the planned pressure support is sufficient. Rotation or circulation does not guarantee zero swab pressure. Stop movement on unexpected drag, fill or flow behaviour, communicate and follow the approved evaluation and influx response.

Use the margin as a limit, not a speed prescription

In the example, the static overbalance is 176 psi. A supplied swab estimate of 100 psi would leave 76 psi overbalance, whereas the 350 psi estimate creates 174 psi underbalance. Neither result establishes an authorised tripping speed: use the actual model, uncertainty, geometry and approved limit. A tight interval or balled assembly can change the pressure response at a previously acceptable speed. Pipe speed alone cannot establish safety without these conditions.

For the opposite movement, suppose the supplied surge estimate is 300 psi. The estimated moving BHP is 7,176 + 300 = 7,476 psi. If the applicable weakest-point allowance for this simplified example is 7,400 psi at the same reference depth, that limit is exceeded by 76 psi. Check the actual pressure at each exposed weak interval in a real well; a bottom-depth comparison cannot replace the complete pressure profile. Surge-induced losses can later reduce static head if fluid level falls.

Measure fill and returns while controlling movement. Unexpected drag, a restricted flow path or an unexplained volume difference requires the approved evaluation and response even if the last model predicted a safe margin. Pumping out changes the fluid balance and pressure support but does not remove the need to monitor both. Record what moved, the fill expected, the volume observed and any rate or drag change so the supervisor can distinguish a geometric change from a possible influx.

Measured depth, horizontal intervals and vessel movement

A long measured flow path can produce significant displacement friction even where its added vertical head is small. Horizontal geometry, eccentric pipe, cuttings beds and restricted BHA clearance can worsen the flow restriction. TVD still sets the simple static head; MD and geometry influence the dynamic flow path. Use the actual tripping assessment rather than treating a shallow TVD as proof of low swab risk.

On a floating rig, vessel motion can move the string relative to the well even without an intended trip. Inadequate motion compensation or an unsuitable fixed support condition can produce repeated upward and downward movement, adding swab/surge transients and confusing volume observations. Confirm the applicable compensation, motion limits and monitoring arrangement with the supervisor. Do not interpret a heave-related volume oscillation as proof that every persistent gain is harmless. Record the motion pattern and distinguish reversible fluctuations from an unexplained cumulative change.