Study guide

6.3 Drillpipe Pressure Step-Down Schedule & Strokes to Bit / Annulus

IWCF Level 4 Drilling Well Control Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Hydrostatic Pressure, Formation Pressure & Wellbore Mechanics

1.1 Hydrostatic Pressure, Mud Weight & Pressure Gradients 1.2 Formation Pore Pressure, Overburden & Fracture Gradient 1.3 U-Tube Concept, ECD & Circulating Friction Losses 1.4 Dynamic Well Pressures, Surge & Swab Effects

2 Chapter 2: Barrier Philosophy, Well Integrity & Human Factors

2.1 The Well Barrier Envelope Concept & Barrier Element Acceptance Criteria 2.2 Well Integrity Monitoring & Leak Detection Standards 2.3 Human Factors, Situational Awareness & Crew Communication in Well Control

3 Chapter 3: Causes of Kicks & Lost Circulation

3.1 Failure to Keep Hole Full, Swabbing & Abnormal Formation Pressure 3.2 Insufficient Fluid Density & Annular Gas Cut Mud Mechanisms 3.3 Lost Circulation, Underground Blowouts & Crossflow Mechanics

4 Chapter 4: Kick Detection, Warning Signs & Shut-in Protocols

4.1 Positive Kick Indicators vs Warning Signs While Drilling 4.2 Kick Detection While Tripping, Flow Checks & Trip Sheet Interpretation 4.3 Hard vs Soft Shut-in Procedures for Surface and Subsea Rigs 4.4 Diverter Operations & Shallow Gas Hazard Management

5 Chapter 5: Influx Mechanics & Gas Behavior

5.1 Influx Characteristics, Gas Solubility & Bubble Point in OBM vs WBM 5.2 Gas Migration Without Circulation & Surface Pressure Buildup 5.3 Gas Expansion, Boyle's Law & Peak Annular Surface Pressures

6 Chapter 6: Well Control Calculations & Kill Sheet

6.1 Shut-In Pressures (SIDPP, SICP) & Influx Height / Gradient 6.2 Kill Mud Weight (KMW), Initial Circulating Pressure (ICP) & Final Circulating Pressure (FCP) 6.3 Drillpipe Pressure Step-Down Schedule & Strokes to Bit / Annulus 6.4 Maximum Allowable Annular Surface Pressure (MAASP) & Casing Shoe Integrity

7 Chapter 7: Constant Bottom Hole Pressure Kill Methods

7.1 The Driller's Method: Two-Circulation Procedure & Detailed Pressure Behavior 7.2 The Wait-and-Weight Method: Single-Circulation Procedure & Comparison 7.3 Choke Manipulation, Drillpipe Gauge Lag Time & Pumping Rate Adjustments 7.4 Well Control Complications: Plugged Nozzles, Washouts & Pump Failure

8 Chapter 8: Volumetric, Stripping & Contingency Methods

8.1 Volumetric Method: Static and Dynamic Gas Migration Control 8.2 Lubricate and Bleed Operations for Surface Pressure Removal 8.3 Stripping and Snubbing Drillstring Under Pressure 8.4 Bullheading Operations & Emergency Off-Bottom Well Control

9 Chapter 9: Blowout Preventers & Associated Rig Equipment

9.1 Annular Preventers: Design, Closing Ratios, Stripping Pressure & Element Selection 9.2 Ram Preventers: Pipe Rams, Variable Bore, Blind Shear Rams & Locking Devices 9.3 Choke Manifolds, Remote Chokes, Buffer Tanks & Articulated Lines 9.4 Mud-Gas Separators, Vacuum Degassers & Drillstring Valves

10 Chapter 10: Control Systems, Testing Standards & Subsea Systems

10.1 Hydraulic Accumulator Closing Units: Sizing, Precharge & API Standard 53 10.2 Hydraulic Control Circuits, Remote Operating Panels & Secondary Controls 10.3 BOP Testing Standards: Low/High Pressure Testing, Function Tests & Drawdown Verification 10.4 Subsea Well Control Equipment: Choke Line Friction, Riser Margin & Multiplex (MUX) Systems

11 Chapter 11: Well Control Incidents, Training & Accreditation

11.1 Major Well Control Incidents & Lessons Learned 11.2 Incident Impact on Personnel, Assets, Environment & Reputation 11.3 Well Control Training, Competence Assurance & Regulatory Framework

12 Chapter 12: Well Control During Casing & Liner Operations

12.1 Surge and Swab Pressure Dynamics During Casing Running 12.2 Casing Fill-Up, Auto-Fill Equipment & Float Valve Integrity 12.3 Casing Float Failure Calculations & Wellbore Fluid Level Loss

13 Chapter 13: Cementing Operations & Pressure Profile Management

13.1 Hydrostatic Pressure Profiles During Cement Pumping & Free-Fall (U-Tubing) 13.2 Gas Migration Mechanisms During Cement Hydration & Gel Strength Development 13.3 Shoe Track Integrity, Backpressure Verification & Cement Barrier Evaluation

14 Chapter 14: Casing Shut-in Procedures & Wireline Pressure Control

14.1 Shut-In Procedures While Running Casing or Liners 14.2 Wireline Well Control: Pressure Effects, Lubricators & Stuffing Boxes 14.3 Wireline BOPs, Chemical Injection & Emergency Wireline Shut-In

15 Chapter 15: Well Control Drills, Response Protocols & Crew Management

15.1 Pit Drills, Trip Drills & Rig Floor Response Timing 15.2 Choke Drills & Pressure Gauge Monitoring Drills 15.3 Supervisor Evaluation, Drill Debriefing & Competency Tracking

16 Chapter 16: Contingency Planning, Equipment Complications & Gauge Diagnostics

16.1 Malfunctioning Pressure Gauge Diagnostics & Trapped Pressure Recognition 16.2 Plugged Drillpipe Nozzles, Float Failures & Drillstring Washouts 16.3 Choke Plugging, Choke Washouts & Choke Manifold Switching 16.4 Hydrate Formation in Subsea Choke Lines & Remediation Strategies

17 Chapter 17: BOP Stack Outlets, Connections & Manifold Hardware

17.1 BOP Side Outlet Valves: Placement, Drilling Spools & HCR Operation 17.2 End Connections, Ring Gaskets (RX/BX) & Flange Make-up Torque 17.3 Choke and Kill Line Routing, Articulated Joints & Flexible Lines

18 Chapter 18: Advanced Well Control: Horizontal & Extended Reach Wells

18.1 Influx Behavior and Hydrostatic Balance in Horizontal Lateral Sections 18.2 Shut-In Pressure Interpretation in Horizontal Wells 18.3 Constant BHP Circulating Kill Procedures for Horizontal Wells

6.3 Drillpipe Pressure Step-Down Schedule & Strokes to Bit / Annulus

Key Takeaways Explain This Topic AI

Pump strokes and displacement volumes must be segmented into drillstring volume (Strokes to Bit, STB) and annular volume (Strokes Bit to Surface, STS) to track fluid interface positions during kill operations.

The drillpipe step-down schedule governs circulating standpipe pressure from ICP to FCP strictly over the STB interval as kill mud replaces original mud inside the drillstring.

Pre-tour Slow Circulating Rate (SCR) pressures must be logged every tour, after mud weight/rheology changes, bit/BHA changes, and across each pump; on subsea stacks, dedicated choke line SCRs establish Choke Line Friction (CLF) to calibrate startup pressures.

IWCF Formulas 24 & 25 govern heavy slug sizing and pit gain due to U-tubing before tripping: Slug Volume = (Length of Dry Pipe × Pipe Capacity × OMW) / (Slug Weight - OMW), producing a pit gain exactly equal to the dry pipe capacity.

Use the method's control phase: Wait-and-Weight follows the drillpipe schedule; the standard second Driller's circulation holds the casing-pressure reference until kill mud reaches the bit, then holds drillpipe FCP. Monitor casing pressure limits throughout.

Last updated: November 2026

As kill mud displaces original mud inside the drillstring, expected standpipe pressure decreases from ICP toward FCP. Wait-and-Weight uses the prepared drillpipe pressure schedule. In the standard second Driller's circulation, after the influx is removed, hold the appropriate casing-pressure reference until kill mud reaches the bit, then control drillpipe pressure at FCP. Track fluid-front volumes and pressure limits throughout.

Rig Volumetrics and Triplex Pump Output Mechanics

All well control stroke calculations depend on the volumetric displacement of the rig mud pumps. Modern rigs utilize single-acting triplex piston pumps.

Triplex Pump Output Formula

PO = 0.000243 × D liner 2 × L stroke × E vol ( bbl/stroke ) \text{PO} = 0.000243 \times D_{\text{liner}}^2 \times L_{\text{stroke}} \times E_{\text{vol}} \quad (\text{bbl/stroke}) PO = 0.000243 × D liner 2 ​ × L stroke ​ × E vol ​ ( bbl/stroke )

Where:

  • D liner D_{\text{liner}} D liner ​ = Inside diameter of the pump liner in inches ( in \text{in} in )
  • L stroke L_{\text{stroke}} L stroke ​ = Piston stroke length in inches ( in \text{in} in )

E vol E_{\text{vol}} E vol ​ = Volumetric pump efficiency (expressed as a decimal, typically 0.95 to 0.98 0.95\text{ to }0.98 0.95 to 0.98 )

0.000243 0.000243 0.000243 = Geometric constant ( π 4 × 3 231 × 42 ) (\frac{\pi}{4} \times \frac{3}{231 \times 42}) ( 4 π ​ × 231 × 42 3 ​ )

Tubular and Annular Capacity Formulas

Internal Pipe Capacity ( C pipe C_{\text{pipe}} C pipe ​ ): C pipe = D in 2 1029.4 ( bbl/ft ) C_{\text{pipe}} = \frac{D_{\text{in}}^2}{1029.4} \quad (\text{bbl/ft}) C pipe ​ = 1029.4 D in 2 ​ ​ ( bbl/ft )

Annular Capacity ( C ann C_{\text{ann}} C ann ​ ): C ann = D hole 2 − D pipe, OD 2 1029.4 ( bbl/ft ) C_{\text{ann}} = \frac{D_{\text{hole}}^2 - D_{\text{pipe, OD}}^2}{1029.4} \quad (\text{bbl/ft}) C ann ​ = 1029.4 D hole 2 ​ − D pipe, OD 2 ​ ​ ( bbl/ft )

Strokes to Bit (STB) and Strokes Bit to Surface (STS)

To manage the kill operation, the supervisor segments the wellbore into two distinct operational volumes:

1. Drillstring Volume and Strokes to Bit (STB)

Total drillstring volume ( V ds V_{\text{ds}} V ds ​ ) is the sum of the internal capacities of the drillpipe, heavyweight drillpipe (HWDP), and drill collars:

V ds = ( L dp × C dp ) + ( L hwdp × C hwdp ) + ( L dc × C dc ) ( bbl ) V_{\text{ds}} = (L_{\text{dp}} \times C_{\text{dp}}) + (L_{\text{hwdp}} \times C_{\text{hwdp}}) + (L_{\text{dc}} \times C_{\text{dc}}) \quad (\text{bbl}) V ds ​ = ( L dp ​ × C dp ​ ) + ( L hwdp ​ × C hwdp ​ ) + ( L dc ​ × C dc ​ ) ( bbl )

With the counter referenced to kill mud entering the drillstring, Strokes to Bit (STB) is:

STB = V ds PO \text{STB} = \frac{V_{\text{ds}}}{\text{PO}} STB = PO V ds ​ ​

If counting from the pump, account separately for the surface-line volume before kill mud enters the string. The IWCF kill sheet lists surface lines separately from drillstring volume.

2. Return-Path Volume and Strokes Bit to Surface (STS)

Total annular volume ( V ann V_{\text{ann}} V ann ​ ) is calculated across each open-hole and cased-hole section:

V ann = ( L dc/oh × C ann, dc/oh ) + ( L dp/oh × C ann, dp/oh ) + ( L dp/csg × C ann, dp/csg ) ( bbl ) V_{\text{ann}} = (L_{\text{dc/oh}} \times C_{\text{ann, dc/oh}}) + (L_{\text{dp/oh}} \times C_{\text{ann, dp/oh}}) + (L_{\text{dp/csg}} \times C_{\text{ann, dp/csg}}) \quad (\text{bbl}) V ann ​ = ( L dc/oh ​ × C ann, dc/oh ​ ) + ( L dp/oh ​ × C ann, dp/oh ​ ) + ( L dp/csg ​ × C ann, dp/csg ​ ) ( bbl )

For returns through this annular path, Strokes Bit to Surface (STS) is:

STS = V ann PO \text{STS} = \frac{V_{\text{ann}}}{\text{PO}} STS = PO V ann ​ ​

For subsea BOP/choke returns, include the choke-line volume in the return-path volume; do not substitute the marine-riser annulus. With the same counter origin, the cumulative interval after bit arrival runs from STB to STB + STS.

Total Circulating Strokes (TCS) for the selected string and return path: TCS = STB + STS \text{TCS} = \text{STB} + \text{STS} TCS = STB + STS

Pre-Tour Slow Circulating Rate (SCR) Recording Intervals and Protocols

Accurate well control requires rigorous pre-kick data acquisition. Baseline circulating pressures must be measured before any well control incident occurs.

Regulatory and Operational SCR Recording Frequency

Slow Circulating Rate (SCR) pressures ( P scr P_{\text{scr}} P scr ​ ) must be taken and recorded on the active kill sheet:

Every Tour (Shift): At the beginning of each 8-hour or 12-hour tour;

Mud Weight & Rheology Changes: Whenever drilling fluid density (mud weight), viscosity, yield point, or gel strength is altered;

Drill Bit Changes: After every bit trip (changes in bit nozzle Total Flow Area, TFA, significantly alter system pressure drop);

BHA & Drillstring Reconfigurations: Whenever drill collars, HWDP, mud motors, MWD/LWD tools, or string dimensions change;

Significant Drilled Footage / Depth Intervals: Every 500 to 1 , 000 ft 500\text{ to }1,000\text{ ft} 500 to 1 , 000 ft ( 150 to 300 m 150\text{ to }300\text{ m} 150 to 300 m ) of newly drilled open hole, or once per 24-hour period during continuous drilling;

Pump Maintenance or Liner Swaps: Whenever pump liners, pistons, or valves are serviced or changed;

Multiple Pump Speeds: At two or three designated kill speeds (e.g., 20 spm 20\text{ spm} 20 spm , 30 spm 30\text{ spm} 30 spm , and 40 spm 40\text{ spm} 40 spm );

Independent Rig Pumps: Separately for each active mud pump on the rig (Pump 1, Pump 2, and Pump 3).

Surface BOP Stacks vs. Subsea BOP Stacks SCR Protocols

The configuration of the blowout preventer fundamentally dictates the circulating friction paths:

Surface BOP Stacks: Normal drilling returns use the normal open return path; a shut-in well is circulated through the BOP side outlet and choke manifold. Measure the selected SCR and assess losses in the actual kill return path rather than assuming bell-nipple returns with the BOP closed.

Subsea BOP Stacks & Choke Line Friction (CLF): On floating drilling vessels (semisubmersibles and drillships), the BOP stack resides on the seabed, connected to the surface rig via marine riser and small-diameter high-pressure choke and kill lines spanning thousands of feet of water depth.

Circulating mud up a long, narrow subsea choke line generates massive frictional pressure resistance known as Choke Line Friction (CLF) .

Measuring Subsea Choke Line Friction (Pre-Tour Procedure):

Riser SCR ( P scr, riser P_{\text{scr, riser}} P scr, riser ​ ): Circulate down the drillpipe and up the marine riser at the kill rate (e.g., 30 spm 30\text{ spm} 30 spm ). Record the standpipe pressure.

Choke Line SCR ( P scr, choke P_{\text{scr, choke}} P scr, choke ​ ): Close the subsea BOP annular preventer or pipe ram, align returns through the subsea choke line to the surface manifold, and pump at the same kill rate ( 30 spm 30\text{ spm} 30 spm ). Record the standpipe pressure.

Calculate Choke Line Friction (CLF): CLF = P scr, choke − P scr, riser \text{CLF} = P_{\text{scr, choke}} - P_{\text{scr, riser}} CLF = P scr, choke ​ − P scr, riser ​

Operational Consequence of CLF During a Well Kill:

In deepwater well control, when the subsea BOP is closed and circulation begins up the choke line, the CLF imposes immediate backpressure against the entire annular wellbore and casing shoe: P bottomhole = P hyd, ann + P casing surface + CLF + Δ P annular friction P_{\text{bottomhole}} = P_{\text{hyd, ann}} + P_{\text{casing surface}} + \text{CLF} + \Delta P_{\text{annular friction}} P bottomhole ​ = P hyd, ann ​ + P casing surface ​ + CLF + Δ P annular friction ​ If the choke operator holds casing pressure constant at stabilized SICP \text{SICP} SICP during pump startup without accounting for CLF, the bottomhole pressure will be overpressured by the full magnitude of CLF \text{CLF} CLF . In a narrow pressure window, this excess pressure can exceed the controlling formation limit and initiate losses. Evaluate the actual margin and monitor for losses or further influx; an underground blowout is a risk, not an automatic result of any extra CLF.

To maintain constant bottomhole pressure during pump startup on a subsea stack, the choke operator must allow casing pressure to drop by an amount equal to CLF \text{CLF} CLF as the pump is brought up to kill speed.

Constructing the Drillpipe Pressure Step-Down Schedule

When kill mud is pumped down the drillpipe, the hydrostatic head inside the string progressively increases because heavy fluid replaces light original mud. To prevent bottomhole pressure from exceeding formation pore pressure, the standpipe pressure must be stepped down continuously from ICP \text{ICP} ICP at stroke 0 to FCP \text{FCP} FCP at stroke STB \text{STB} STB .

Mathematical Formulation: Pressure Drop per 100 Strokes

To facilitate operational monitoring on the choke console, the step-down rate is calculated per 100 pump strokes:

Δ P 100 = ICP − FCP STB / 100 = ( ICP − FCP ) × 100 STB ( psi / 100 strokes ) \Delta P_{100} = \frac{\text{ICP} - \text{FCP}}{\text{STB} / 100} = \frac{(\text{ICP} - \text{FCP}) \times 100}{\text{STB}} \quad (\text{psi / 100 strokes}) Δ P 100 ​ = STB /100 ICP − FCP ​ = STB ( ICP − FCP ) × 100 ​ ( psi / 100 strokes )

For any intermediate cumulative stroke count ( S S S ):

SPP ( S ) = ICP − ( S × ICP − FCP STB ) \text{SPP}(S) = \text{ICP} - \left( S \times \frac{\text{ICP} - \text{FCP}}{\text{STB}} \right) SPP ( S ) = ICP − ( S × STB ICP − FCP ​ )

Assumptions Behind the Linear Schedule

The simple linear kill sheet assumes approximately constant vertical displacement per stroke and the standard ICP-to-FCP hydraulic interpolation. A uniform vertical pipe, or a constant-inclination uniform segment, gives equal vertical increments for equal pumped volumes: Δ P hyd = 0.052 ( KMW − OMW ) Δ h TVD \Delta P_{\text{hyd}}=0.052(\text{KMW}-\text{OMW})\Delta h_{\text{TVD}} Δ P hyd ​ = 0.052 ( KMW − OMW ) Δ h TVD ​ Uniform bore alone is insufficient when inclination changes. Use surveyed TVD increments, measured-length capacities and the approved segmented pressure schedule for a deviated well or changing string dimensions.

Execute the Prepared Schedule

For Wait-and-Weight, follow the approved geometry-dependent drillpipe schedule to bit arrival, then hold FCP through the planned return displacement. Keep pump flow steady and monitor annular pressure limits.

For subsea returns, a static kill-line monitor can provide a nonflowing pressure reference. Include its known fluid head and gauge elevation when relating that reading to stack or bottomhole pressure. A flowing choke gauge requires CLF compensation on rate changes; do not equate either raw surface reading with seabed pressure.

Pipe Tripping Mechanics: Heavy Slug Sizing and Pit Gain Calculations (IWCF EX-0035)

Prior to pulling the drillstring out of the hole (POOH) for a bit change or BHA trip, drillers pump a small volume of high-density drilling fluid—termed a heavy slug —into the top of the drillpipe.

Operational Rationale for Pumping a Slug

Preventing Wet Pulling (Mud Spills): If upper pipe remains filled when a connection is broken, mud can spill onto the rig floor, creating slip hazards, mud loss and contamination. A correctly planned slug lowers the internal fluid level so the selected upper stands can be pulled dry.

Controlling Mud Drainage: The dry upper interval reduces mud spilling from disconnected pipe. It does not eliminate annular swabbing; pull speed, fluid rheology and clearance still require control.

Ensuring Accurate Hole Fill Monitoring: A dry string allows precise measurement of steel displacement in the trip tank without contamination from surface drainage.

U-Tube Mechanics of a Heavy Slug

Once the heavy slug is pumped into the drillstring and the top of the string is opened (vented) to atmosphere at the surface, a U-tube imbalance exists between the heavy slug column inside the drillpipe and the lighter mud in the annulus.

Gravity pulls the heavy slug down the drillstring until the hydrostatic pressure inside the pipe balances the hydrostatic head in the annulus:

P hyd, pipe = P hyd, annulus P_{\text{hyd, pipe}} = P_{\text{hyd, annulus}} P hyd, pipe ​ = P hyd, annulus ​ 0.052 × ρ slug × L slug = 0.052 × ρ current × ( L slug + L dry ) 0.052 \times \rho_{\text{slug}} \times L_{\text{slug}} = 0.052 \times \rho_{\text{current}} \times (L_{\text{slug}} + L_{\text{dry}}) 0.052 × ρ slug ​ × L slug ​ = 0.052 × ρ current ​ × ( L slug ​ + L dry ​ )

Where:

  • ρ slug \rho_{\text{slug}} ρ slug ​ = Density of the heavy slug ( ppg \text{ppg} ppg )
  • ρ current \rho_{\text{current}} ρ current ​ = Density of the active drilling mud ( ppg \text{ppg} ppg )
  • L slug L_{\text{slug}} L slug ​ = Vertical length of the slug column inside the drillpipe ( ft \text{ft} ft )

L dry L_{\text{dry}} L dry ​ = Desired vertical length of dry (evacuated) drillpipe below the rotary table ( ft \text{ft} ft )

Expanding and rearranging: ρ slug × L slug = ρ current × L slug + ρ current × L dry \rho_{\text{slug}} \times L_{\text{slug}} = \rho_{\text{current}} \times L_{\text{slug}} + \rho_{\text{current}} \times L_{\text{dry}} ρ slug ​ × L slug ​ = ρ current ​ × L slug ​ + ρ current ​ × L dry ​ L slug × ( ρ slug − ρ current ) = ρ current × L dry L_{\text{slug}} \times (\rho_{\text{slug}} - \rho_{\text{current}}) = \rho_{\text{current}} \times L_{\text{dry}} L slug ​ × ( ρ slug ​ − ρ current ​ ) = ρ current ​ × L dry ​ L slug = L dry × ρ current ρ slug − ρ current L_{\text{slug}} = \frac{L_{\text{dry}} \times \rho_{\text{current}}}{\rho_{\text{slug}} - \rho_{\text{current}}} L slug ​ = ρ slug ​ − ρ current ​ L dry ​ × ρ current ​ ​

IWCF Formula 24: Slug Volume Calculation

Multiplying the required slug column length ( L slug L_{\text{slug}} L slug ​ ) by the internal capacity of the drillpipe ( C pipe C_{\text{pipe}} C pipe ​ in bbl/ft \text{bbl/ft} bbl/ft ), where Slug Volume = L slug × C pipe \text{Slug Volume} = L_{\text{slug}} \times C_{\text{pipe}} Slug Volume = L slug ​ × C pipe ​ :

Slug Volume (bbl) = Length of Dry Pipe (ft) × Pipe Capacity (bbl/ft) × ρ current ( ppg ) ρ slug ( ppg ) − ρ current ( ppg ) \text{Slug Volume (bbl)} = \frac{\text{Length of Dry Pipe (ft)} \times \text{Pipe Capacity (bbl/ft)} \times \rho_{\text{current}} (\text{ppg})}{\rho_{\text{slug}} (\text{ppg}) - \rho_{\text{current}} (\text{ppg})} Slug Volume (bbl) = ρ slug ​ ( ppg ) − ρ current ​ ( ppg ) Length of Dry Pipe (ft) × Pipe Capacity (bbl/ft) × ρ current ​ ( ppg ) ​

In Metric / SI Units ( m 3 \text{m}^3 m 3 , m \text{m} m , m 3 / m \text{m}^3/\text{m} m 3 / m , and SG \text{SG} SG or kg/m 3 \text{kg/m}^3 kg/m 3 ):

Slug Volume ( m 3 ) = Length of Dry Pipe (m) × Pipe Capacity ( m 3 / m ) × ρ current ρ slug − ρ current \text{Slug Volume } (\text{m}^3) = \frac{\text{Length of Dry Pipe (m)} \times \text{Pipe Capacity } (\text{m}^3/\text{m}) \times \rho_{\text{current}}}{\rho_{\text{slug}} - \rho_{\text{current}}} Slug Volume ( m 3 ) = ρ slug ​ − ρ current ​ Length of Dry Pipe (m) × Pipe Capacity ( m 3 / m ) × ρ current ​ ​

IWCF Formula 25: Pit Gain Due to Slug U-Tubing

As the heavy slug falls down the drillstring to achieve hydrostatic balance, it displaces an equivalent volume of mud out of the annulus and into the surface active pits. This pit volume increase is calculated as:

Pit Gain (bbl) = Slug Volume (bbl) × ( ρ slug ( ppg ) ρ current ( ppg ) − 1 ) \text{Pit Gain (bbl)} = \text{Slug Volume (bbl)} \times \left( \frac{\rho_{\text{slug}} (\text{ppg})}{\rho_{\text{current}} (\text{ppg})} - 1 \right) Pit Gain (bbl) = Slug Volume (bbl) × ( ρ current ​ ( ppg ) ρ slug ​ ( ppg ) ​ − 1 )

In Metric / SI Units:

Pit Gain ( m 3 ) = Slug Volume ( m 3 ) × ( ρ slug ρ current − 1 ) \text{Pit Gain } (\text{m}^3) = \text{Slug Volume } (\text{m}^3) \times \left( \frac{\rho_{\text{slug}}}{\rho_{\text{current}}} - 1 \right) Pit Gain ( m 3 ) = Slug Volume ( m 3 ) × ( ρ current ​ ρ slug ​ ​ − 1 )

Physical Proof of the Pit Gain Identity

Substituting Formula 24 into Formula 25 reveals a fundamental physical property of the wellbore U-tube:

Pit Gain = [ L dry × C pipe × ρ current ρ slug − ρ current ] × [ ρ slug − ρ current ρ current ] = L dry × C pipe \text{Pit Gain} = \left[ \frac{L_{\text{dry}} \times C_{\text{pipe}} \times \rho_{\text{current}}}{\rho_{\text{slug}} - \rho_{\text{current}}} \right] \times \left[ \frac{\rho_{\text{slug}} - \rho_{\text{current}}}{\rho_{\text{current}}} \right] = L_{\text{dry}} \times C_{\text{pipe}} Pit Gain = [ ρ slug ​ − ρ current ​ L dry ​ × C pipe ​ × ρ current ​ ​ ] × [ ρ current ​ ρ slug ​ − ρ current ​ ​ ] = L dry ​ × C pipe ​

Pit Gain Due to U-Tubing ≡ Internal Capacity Volume of Dry Pipe \mathbf{\text{Pit Gain Due to U-Tubing} \equiv \text{Internal Capacity Volume of Dry Pipe}} Pit Gain Due to U-Tubing ≡ Internal Capacity Volume of Dry Pipe

Important

The ideal equilibrium U-tube gain equals the dry internal pipe volume. Compare measured gain with that prediction, allowing for slug placement and measurement/transfer effects. An unexplained excess or shortfall requires investigation for influx, losses, restrictions or other volume changes; it is not a unique diagnosis. Maintain hole-fill monitoring throughout the trip.

Step-by-Step Worked Field Problem: Heavy Slug Sizing & Pit Gain

A drilling crew is preparing to trip pipe out of the hole. The supervisor requires a dry drillstring interval to ensure clean, safe handling on the rig floor.

Well Depth: 10 , 500 ft TVD / 11 , 800 ft MD 10,500\text{ ft TVD} / 11,800\text{ ft MD} 10 , 500 ft TVD /11 , 800 ft MD

  • Current Mud Weight ( ρ current \rho_{\text{current}} ρ current ​ ): 12.0 ppg 12.0\text{ ppg} 12.0 ppg
  • Heavy Slug Mud Weight ( ρ slug \rho_{\text{slug}} ρ slug ​ ): 14.5 ppg 14.5\text{ ppg} 14.5 ppg

Desired Length of Dry Drillpipe ( L dry L_{\text{dry}} L dry ​ ): 200 ft 200\text{ ft} 200 ft (approximately 2 stands)

5 in 5\text{ in} 5 in , 19.5 lb/ft 19.5\text{ lb/ft} 19.5 lb/ft Drillpipe Capacity ( C pipe C_{\text{pipe}} C pipe ​ ): 0.0178 bbl/ft 0.0178\text{ bbl/ft} 0.0178 bbl/ft

  • Mud Pump Output ( PO \text{PO} PO ): 0.119 bbl/stroke 0.119\text{ bbl/stroke} 0.119 bbl/stroke
  • Step 1: Calculate the Internal Volume of Dry Pipe Desired

V dry = L dry × C pipe = 200 ft × 0.0178 bbl/ft = 3.56 bbl V_{\text{dry}} = L_{\text{dry}} \times C_{\text{pipe}} = 200\text{ ft} \times 0.0178\text{ bbl/ft} = \mathbf{3.56\text{ bbl}} V dry ​ = L dry ​ × C pipe ​ = 200 ft × 0.0178 bbl/ft = 3.56 bbl

Step 2: Calculate Required Heavy Slug Volume (IWCF Formula 24)

V slug = 200 ft × 0.0178 bbl/ft × 12.0 ppg 14.5 ppg − 12.0 ppg V_{\text{slug}} = \frac{200\text{ ft} \times 0.0178\text{ bbl/ft} \times 12.0\text{ ppg}}{14.5\text{ ppg} - 12.0\text{ ppg}} V slug ​ = 14.5 ppg − 12.0 ppg 200 ft × 0.0178 bbl/ft × 12.0 ppg ​ V slug = 3.56 bbl × 12.0 2.5 = 42.72 2.5 = 17.088 bbl ≈ 17.1 bbl V_{\text{slug}} = \frac{3.56\text{ bbl} \times 12.0}{2.5} = \frac{42.72}{2.5} = \mathbf{17.088\text{ bbl}} \approx \mathbf{17.1\text{ bbl}} V slug ​ = 2.5 3.56 bbl × 12.0 ​ = 2.5 42.72 ​ = 17.088 bbl ≈ 17.1 bbl

Step 3: Calculate Expected Pit Gain Due to U-Tubing (IWCF Formula 25)

Pit Gain = 17.088 bbl × ( 14.5 ppg 12.0 ppg − 1 ) \text{Pit Gain} = 17.088\text{ bbl} \times \left( \frac{14.5\text{ ppg}}{12.0\text{ ppg}} - 1 \right) Pit Gain = 17.088 bbl × ( 12.0 ppg 14.5 ppg ​ − 1 ) Pit Gain = 17.088 × ( 1.20833 − 1 ) = 17.088 × 0.20833 = 3.56 bbl \text{Pit Gain} = 17.088 \times (1.20833 - 1) = 17.088 \times 0.20833 = \mathbf{3.56\text{ bbl}} Pit Gain = 17.088 × ( 1.20833 − 1 ) = 17.088 × 0.20833 = 3.56 bbl (Notice that the calculated pit gain of 3.56 bbl 3.56\text{ bbl} 3.56 bbl exactly equals the internal volume of the 200 ft 200\text{ ft} 200 ft dry drillpipe calculated in Step 1.)

Step 4: Calculate Pump Strokes to Mix and Place Slug

Strokes to pump slug into drillstring: Strokes slug = 17.088 bbl 0.119 bbl/stroke = 144 strokes \text{Strokes}_{\text{slug}} = \frac{17.088\text{ bbl}}{0.119\text{ bbl/stroke}} = \mathbf{144\text{ strokes}} Strokes slug ​ = 0.119 bbl/stroke 17.088 bbl ​ = 144 strokes

Displacement: Depending on company policy, the slug is pumped into the string and either left at surface or displaced down the drillstring with a predetermined volume of active mud before disconnecting the top drive/kelly. The string is then vented to atmosphere, allowing the slug to drop and the expected 3.56 bbl 3.56\text{ bbl} 3.56 bbl pit gain to register on the PVT.

Choose the Pressure Reference for the Kill Phase

During Wait-and-Weight, the annulus still contains the influx. Follow the prepared drillpipe pressure schedule as kill mud moves down the string; do not force casing pressure to follow the same curve. Continue monitoring casing pressure, returns and current formation/equipment limits.

During the standard second Driller's circulation, the influx has already been removed and the annulus initially contains original mud. Hold the appropriate casing-pressure reference (original SIDPP in the simple surface case) until kill mud reaches the bit. Drillpipe pressure declines as string hydrostatic head increases. Then hold drillpipe pressure at FCP while kill mud displaces the annulus. Include subsea CLF and actual fluid-head corrections where applicable.

Worked Field Problem: Step-Down Schedule Construction

For this arithmetic exercise, use the supplied linear ICP-to-FCP interpolation. A field schedule for 11 , 000 ft TVD / 12 , 500 ft MD 11,000\text{ ft TVD} / 12,500\text{ ft MD} 11 , 000 ft TVD /12 , 500 ft MD would additionally require survey and string-segment data.

  • Pump Displacement: PO = 0.1183 bbl/stroke \text{PO} = 0.1183\text{ bbl/stroke} PO = 0.1183 bbl/stroke
  • Drillstring Volume: V ds = 213.9 bbl V_{\text{ds}} = 213.9\text{ bbl} V ds ​ = 213.9 bbl

STB = 213.9 bbl 0.1183 bbl/stroke = 1 , 808 strokes \text{STB} = \frac{213.9\text{ bbl}}{0.1183\text{ bbl/stroke}} = 1,808\text{ strokes} STB = 0.1183 bbl/stroke 213.9 bbl ​ = 1 , 808 strokes

  • ICP = 1 , 220 psi \text{ICP} = 1,220\text{ psi} ICP = 1 , 220 psi
  • FCP = 740 psi \text{FCP} = 740\text{ psi} FCP = 740 psi

Calculation of Step-Down Rate:

Δ P total = ICP − FCP = 1 , 220 − 740 = 480 psi \Delta P_{\text{total}} = \text{ICP} - \text{FCP} = 1,220 - 740 = 480\text{ psi} Δ P total ​ = ICP − FCP = 1 , 220 − 740 = 480 psi Δ P 100 = 480 1 , 808 / 100 = 480 18.08 = 26.55 psi per 100 strokes \Delta P_{100} = \frac{480}{1,808 / 100} = \frac{480}{18.08} = \mathbf{26.55\text{ psi per 100 strokes}} Δ P 100 ​ = 1 , 808/100 480 ​ = 18.08 480 ​ = 26.55 psi per 100 strokes

Step-Down Table for Rig Floor Choke Console:

  • Cumulative Strokes Target Standpipe Pressure (psi) Operational Status
  • 0 1 , 220 1,220 1 , 220 (ICP) At kill rate; begin the prepared drillpipe-pressure schedule
  • 200 1 , 167 1,167 1 , 167 Step-down active; track strokes on counter
  • 400 1 , 114 1,114 1 , 114 Drillpipe pressure controlled via choke adjustments
  • 600 1 , 061 1,061 1 , 061 Casing pressure floating freely
  • 800 1 , 008 1,008 1 , 008 Mid-string displacement
  • 1,000 955 955 955 Drillpipe pressure tracking linear slope
  • 1,200 901 901 901 Monitoring for pump speed variations
  • 1,400 848 848 848 Continue checking the supplied interpolation target
  • 1,600 795 795 795 Continue tracking; segment arrival needs actual string geometry
  • 1,808 (STB) 740 740 740 (FCP) Kill mud arrives at bit nozzles
  • > 1,808 740 740 740 (Hold Constant) Hold FCP constant until kill mud reaches surface

Loading diagram... Drillpipe Pressure Step-Down Schedule Architecture