Study guide

3.7 Calculation Foundation Case Lab

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

3.7 Calculation Foundation Case Lab

Key Takeaways Explain This Topic AI

Mixed calculation cases should be broken into small decisions: system type, load category, unit conversion, adjustment factor, and final code step.

The same case may contain theory math, voltage-drop analysis, continuous-load sizing, and NEC navigation cues.

A correct numerical answer is not enough unless it answers the exact question asked: current, VA, ampacity, percent drop, or next code selection.

Exam practice should include wrong-answer diagnosis so distractors become recognizable patterns.

Last updated: May 2026

Case labs turn formulas into exam habits

The goal of calculation practice is not to memorize isolated equations. The goal is to recognize which equation, table, or NEC rule belongs to the facts in front of you. A journeyman electrician exam question may be short, but it often compresses several decisions into one sentence. You need a repeatable way to unpack it.

Use this lab method:

Box the final ask.

Underline the system voltage and phase.

Mark each load as continuous, noncontinuous, motor, heating, cooling, lighting, receptacle, or special equipment.

Convert units once, not repeatedly.

Apply only the factor that belongs to that load and rule.

Keep the calculated value until the question asks for a standard size, conductor, or table selection.

Compare each answer choice to a known trap.

Case 1: mixed branch-circuit load

A 120-volt branch circuit supplies 960 VA of noncontinuous equipment load and 1,440 VA of continuous lighting load. What is the minimum branch-circuit ampacity before selecting conductors?

Final ask: ampacity, not overcurrent device size. System: 120 V single-phase branch circuit. Load groups: 960 VA noncontinuous and 1,440 VA continuous.

Adjusted VA = 960 + (1,440 x 1.25) = 960 + 1,800 = 2,760 VA. Current = 2,760 / 120 = 23 A.

Distractor diagnosis: 20 A comes from adding 2,400 VA and dividing by 120 without the continuous factor. 25 A may be the next standard overcurrent rating, but the question asks minimum ampacity before conductor selection. 30 A may come from rounding too aggressively or applying a rule not stated.

Case 2: three-phase kVA current

A balanced 60 kVA load is supplied by a 208-volt, three-phase feeder. What is the approximate line current?

Final ask: line current. Formula: I = VA / (1.732 x E). Convert 60 kVA to 60,000 VA.

I = 60,000 / (1.732 x 208) = 60,000 / 360.256 = 166.5 A.

Distractor diagnosis: 288.5 A comes from 60,000 / 208 and ignores the three-phase factor. 96.2 A may come from using 360 V or another wrong voltage. 60 A treats kVA as amperes. The correct answer is about 167 A before any code sizing rule.

Case 3: voltage drop percent

A 240-volt single-phase circuit has an actual calculated voltage drop of 7.2 volts. What is the voltage-drop percentage?

VD percent = VD / circuit voltage x 100. Use 7.2 / 240 x 100 = 3 percent.

Distractor diagnosis: 7.2 percent confuses volts with percent. 6 percent may come from dividing by 120 even though the load is 240 V. 0.03 is the decimal form before multiplying by 100. If the question asks for percent, give 3 percent, not 0.03.

Case 4: conductor size from voltage drop setup

A 120-volt single-phase copper circuit carries 18 A for 100 ft one way. The design limit is 3 percent voltage drop. Use K = 12.9. What circular-mil area is required by voltage drop before checking ampacity?

First find allowed volts dropped: 120 x 0.03 = 3.6 V. Rearrange the single-phase formula:

CM = 2 x K x I x D / VD

CM = 2 x 12.9 x 18 x 100 / 3.6 = 46,440 / 3.6 = 12,900 circular mils.

The conductor selected for voltage drop must have at least that circular-mil area, and then it must still satisfy NEC ampacity, insulation, terminal, adjustment, correction, and overcurrent rules. Voltage drop does not replace ampacity.

Distractor diagnosis: 6,450 circular mils comes from forgetting the return path multiplier. 15,480 may come from using aluminum K approximately but the case says copper. 430 circular mils comes from dividing in the wrong order.

Case 5: demand factor caution

A question states that a non-dwelling feeder supplies 20,000 VA of connected receptacle load and asks for calculated load using a specific NEC demand table. The table permits a certain portion at 100 percent and the remainder at a reduced percentage. This is not a theory-only problem. It is a code-navigation problem with arithmetic after the table is found.

Do not invent a demand factor from memory unless you are certain it applies to that occupancy, load, and NEC edition. R17, T17, and G17 are tied to different NEC editions. The broad workflow is stable, but exact table text and numbering can vary. On the exam, the listed reference controls.

Case 6: motor nameplate trap

A motor question gives horsepower, voltage, and nameplate current, then asks for branch-circuit short-circuit and ground-fault protection. This is not an invitation to convert horsepower to watts and divide by voltage. Motor articles often require table full-load current for conductor and protection calculations, while nameplate current may be used for overload protection. The question wording and NEC rule decide the current source.

A good scratch note is: motor? table or nameplate? largest motor? percentage? This forces you to pause before using ordinary Ohm's Law.

Case 7: final-ask discipline

Consider a feeder calculation that produces 137.5 A. If the question asks for calculated load current, the answer is 137.5 A. If it asks for minimum conductor ampacity, you may need a conductor with sufficient ampacity after temperature limitations and adjustment or correction. If it asks for standard overcurrent protection, you may need to apply the NEC standard-size rule and any limits specific to the equipment. If it asks for service rating, additional service rules may apply.

Many candidates lose points after doing the hard part correctly because they answer one step too early or one step too late. The phrase before adjustment, minimum ampacity, next standard size, calculated load, and not less than are signals. Circle them mentally.

Exam-day calculation habits

Use a clean sequence for every math item. Write the formula in abbreviated form. Substitute values with units. Keep one extra decimal. Check magnitude. Then read the final ask again before choosing. If answer choices are numerical, identify what each distractor likely represents. One option may omit 125 percent, one may use single-phase instead of three-phase, one may use the wrong voltage, and one may be the correct calculation.

Because ICC contractor and trades exams are multiple choice with no guessing penalty, never leave a calculation blank. If time is nearly gone, eliminate choices with wrong units, impossible magnitude, or familiar trap patterns. A disciplined estimate can turn a rushed question into a reasonable selection.