Study guide
3.2 Series, Parallel, and Circuit Behavior
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
3.2 Series, Parallel, and Circuit Behavior
Key Takeaways Explain This Topic AI
Series circuits have one current path, so current is the same through each load and voltage divides across the loads.
Parallel circuits have multiple paths, so voltage is the same across each branch and current divides according to branch resistance.
Most building loads are connected in parallel, but exam questions still use series behavior to test fundamentals, controls, and fault reasoning.
Equivalent resistance, total current, and voltage relationships should be checked against the physical behavior of the circuit.
Last updated: May 2026
Circuit behavior is a reasoning tool
Journeyman exams do not test theory as an isolated classroom exercise. They use theory to see whether you understand what happens when a load opens, a connection loosens, a neutral is lost, a switch is placed in the wrong part of a circuit, or several loads are connected to one feeder. The same ideas also support conductor sizing and overcurrent protection because current depends on how loads are connected.
A circuit needs a source, an ungrounded conductor path, a load, and a return path. In normal premises wiring, branch loads are generally placed in parallel so each load receives the intended system voltage. A luminaire, receptacle load, and appliance on a 120-volt branch circuit are not intended to share voltage in series. If they did, turning one off or opening one load could affect the others.
Series vs. Parallel Quick Table
Feature Series circuit Parallel circuit Exam use
Current Same current through every component Current divides among paths Decide whether to add currents or use one current
Voltage Source voltage divides across loads Each branch gets source voltage Explain why premises loads are normally parallel
Resistance Total resistance adds directly Total resistance is less than the smallest branch Avoid adding branch resistances in parallel problems
Open point One open can stop the whole path One open branch may leave other branches operating Diagnose opens, loose connections, and failed loads
Common exam trap Treating every load as if voltage is unchanged Treating every branch as if current is identical Start with circuit type before using formulas
Series circuits
In a series circuit, there is only one path for current. The same current flows through every component. Total resistance is the sum of the resistances.
Rtotal = R1 + R2 + R3 + ...
If a 120-volt circuit has a 10-ohm resistor and a 20-ohm resistor in series, total resistance is 30 ohms. Current is I = E / R = 120 / 30 = 4 A. The voltage across the 10-ohm resistor is E = I x R = 4 x 10 = 40 V. The voltage across the 20-ohm resistor is 4 x 20 = 80 V. The drops add back to the source voltage: 40 + 80 = 120 V.
The field lesson is that voltage divides in proportion to resistance. A high-resistance connection in series with a load can drop voltage, heat, and leave the load operating poorly. The exam may describe dim lamps, low voltage at a motor, or heat at a splice. Theory points you toward a series resistance problem even before the code rule is considered.
Parallel circuits
In a parallel circuit, each branch connects across the same two points. Voltage is the same across each branch. Current in each branch depends on that branch's resistance, and total current is the sum of branch currents.
Itotal = I1 + I2 + I3 + ...
For resistance, the reciprocal method is:
1 / Rtotal = 1 / R1 + 1 / R2 + 1 / R3 + ...
For two resistors only, a shortcut is:
Rtotal = (R1 x R2) / (R1 + R2)
Example: a 120-volt source supplies a 20-ohm branch and a 30-ohm branch in parallel. Branch current one is 120 / 20 = 6 A. Branch current two is 120 / 30 = 4 A. Total current is 10 A. Equivalent resistance is 120 / 10 = 12 ohms. Notice that equivalent resistance is lower than either branch resistance. That is a key sanity check.
Building wiring connection
Most utilization equipment in a building is connected in parallel. A 120-volt receptacle on a multioutlet branch circuit should receive about 120 volts whether another receptacle load is plugged in or not, subject to normal voltage drop. A 240-volt water heater should not depend on a range element being energized. The parallel model is why adding loads generally increases total current without reducing nominal voltage at every load.
Controls may use series logic. A safety switch, limit switch, overload contact, thermostat, or stop button may be placed in series with a control coil so opening any one device stops the circuit. A start button or holding contact may be placed in parallel with another control path. The exam domain for control devices is smaller than wiring methods, but series and parallel reasoning helps you answer those items quickly.
Opens and shorts
An open in a series circuit stops current everywhere in that path. An open in one branch of a parallel circuit stops current only in that branch, while other branches may continue operating. A short circuit creates an unintended low-impedance path and can cause very high current until an overcurrent protective device operates. A ground fault is an unintended connection to ground or grounded parts.
Do not casually call every problem a short. A high-resistance connection, open neutral, line-to-ground fault, and line-to-line short have different symptoms and code consequences. On the exam, language matters. If the question asks for current in an open branch, the branch current is zero. If it asks for total current after one parallel branch opens, subtract only that branch current.
Worked example: branch opens
A 120-volt circuit has three parallel resistance loads: 12 ohms, 24 ohms, and 60 ohms. The 24-ohm branch opens. What is the new total current?
Before the open, currents were 10 A, 5 A, and 2 A, for 17 A total. After the 24-ohm branch opens, that branch current is zero. The remaining current is 10 A + 2 A = 12 A. The voltage across the remaining parallel branches is still 120 V in the ideal calculation.
A common trap is recalculating the opened branch as infinite current or adding the resistance values as if the loads became series. An open branch has no complete path, so it has no branch current.
Calculator setup
For series resistance, addition is direct. For parallel resistance, use branch current when voltage is known; it is often cleaner than reciprocal resistance. If the question gives voltage and branch resistances, calculate each branch current and add. If the question gives only resistances and asks for equivalent resistance, use the reciprocal formula and check that the answer is less than the smallest branch resistance.
Exam traps
Watch for the word total. Total current in a parallel circuit is not the current through each load. Watch for equal resistances. Two equal resistors in parallel have half the resistance of one resistor, and three equal resistors have one-third. Watch for voltage in series. The full source voltage is not automatically across each series component. It divides according to resistance.
Finally, keep code and theory in their proper places. Series and parallel math can tell you the current. The NEC then tells you how conductors, overcurrent devices, boxes, wiring methods, and equipment must be selected and installed.