Study guide

3.5 Voltage Drop and Practical Calculation Setup

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

3.5 Voltage Drop and Practical Calculation Setup

Key Takeaways Explain This Topic AI

Voltage drop is a performance calculation, not usually an overcurrent protection calculation, but it appears often in design and exam setup questions.

The common single-phase and three-phase voltage-drop formulas require conductor resistance or a circular-mil shortcut, circuit length, current, and voltage.

Length means one-way circuit length in common NEC-style voltage-drop formulas that already account for the return path or three-phase relationship.

Exam traps include using feet twice, mixing copper and aluminum constants, and confusing voltage drop percent with actual volts dropped.

Last updated: May 2026

Voltage drop is about delivered voltage

Voltage drop is the reduction in voltage caused by conductor impedance as current flows. A load may be code-compliant for ampacity and overcurrent protection yet still perform poorly if the circuit is long and the voltage at the equipment is too low. Motors may run hot, lights may dim, and electronic equipment may misbehave.

The NEC includes informational guidance for reasonable voltage drop in branch circuits and feeders, but the exam may ask whether a given drop meets a design recommendation or may simply ask you to calculate the drop. Treat the specific question carefully. A voltage-drop recommendation is not the same as a mandatory ampacity rule unless a particular article, equipment instruction, or local amendment makes it enforceable.

Common formulas

One common single-phase formula using conductor resistance is:

VD = 2 x K x I x D / CM

One common three-phase formula is:

VD = 1.732 x K x I x D / CM

Where VD is voltage drop in volts, K is the conductor constant, I is current in amperes, D is one-way distance in feet, and CM is conductor area in circular mils. Common approximate K values are 12.9 for copper and 21.2 for aluminum, but always use the values supplied by the question or required reference if they differ.

Voltage drop percent is:

VD percent = (VD / circuit voltage) x 100

If you calculate a 6-volt drop on a 120-volt circuit, the drop is 6 / 120 x 100 = 5 percent. If the same 6-volt drop occurs on a 240-volt circuit, the percent is 2.5 percent. The volts dropped are the same, but the percentage is different.

Worked example: single-phase voltage drop

A 120-volt, single-phase, two-wire copper branch circuit supplies 16 A at a one-way distance of 75 ft. The conductor area is 6,530 circular mils. Use K = 12.9. Find approximate voltage drop.

VD = 2 x 12.9 x 16 x 75 / 6,530.

First multiply the numerator: 2 x 12.9 = 25.8. 25.8 x 16 = 412.8. 412.8 x 75 = 30,960. Divide by 6,530 = 4.74 V.

Percent drop = 4.74 / 120 x 100 = 3.95 percent.

The 2 in the formula accounts for the outgoing and return conductor path in a single-phase two-wire circuit. Do not double the 75 ft distance again when using this formula. If you use 150 ft for D and also keep the 2, the answer doubles incorrectly.

Worked example: three-phase voltage drop

A 480-volt, three-phase copper feeder carries 80 A for 150 ft one way. The conductor area is 41,740 circular mils. Use K = 12.9.

VD = 1.732 x 12.9 x 80 x 150 / 41,740.

1.732 x 12.9 = 22.3428. Multiply by 80 = 1,787.424. Multiply by 150 = 268,113.6. Divide by 41,740 = 6.42 V.

Percent drop = 6.42 / 480 x 100 = 1.34 percent.

A common wrong answer uses the single-phase 2 instead of 1.732. Another wrong answer divides by 277 because the system may be 277/480 V. If the feeder is serving a 480-volt three-phase load, use 480 as the circuit voltage for percent drop.

Conductor resistance method

Some questions give conductor resistance in ohms per 1,000 ft instead of circular mils. In that case, calculate resistance for the circuit length and use Ohm's Law.

For a single-phase two-wire circuit:

  • Total conductor resistance = resistance per 1,000 ft x (2 x one-way ft / 1,000)
  • VD = I x total resistance

Example: a conductor is 0.50 ohm per 1,000 ft. The one-way length is 200 ft and current is 20 A. Total conductor length for the current path is 400 ft. Resistance is 0.50 x 400 / 1,000 = 0.20 ohm. Voltage drop is 20 x 0.20 = 4 V.

This method makes the return path explicit, so do not also use the 2 x K formula. Use one method consistently.

Practical setup checklist

Before calculating, identify these facts:

Is the circuit single-phase or three-phase?

What is the circuit voltage at the load?

Is the conductor copper or aluminum?

What is the one-way length?

What current should be used: actual load current, calculated load, or design current?

What conductor size or circular-mil area is given?

Does the question ask for volts dropped, percent drop, or minimum conductor size?

If the question asks for minimum conductor size, you may need to rearrange the formula:

  • CM = 2 x K x I x D / VD for single-phase
  • CM = 1.732 x K x I x D / VD for three-phase

Then compare the required CM to conductor sizes. Choose a conductor with circular-mil area equal to or larger than the required value, subject to ampacity and installation rules. Voltage drop alone does not prove the conductor is code-compliant for ampacity.

Exam traps

The most common trap is length. Many formulas use one-way distance because the formula already includes the path multiplier. Read whether the question states one-way length or total conductor length. The second trap is material. Aluminum has higher resistance than copper, so using copper K for aluminum understates the voltage drop. The third trap is percent. A calculated 3.6 V drop is not 3.6 percent unless the circuit voltage is 100 V.

The fourth trap is treating informational recommendations as universal pass-fail rules. The ICC exam is based on listed references, including the applicable NEC edition for R17, T17, or G17. Use the code book for enforceable requirements and use voltage-drop calculations for the performance question being asked.

Calculator discipline

For a basic calculator, compute the numerator in chunks and write the result before dividing by circular mils. If the answer choices are close, carry two decimals. After calculating volts, always divide by system voltage and multiply by 100 if the answer asks for percent. If a percent answer is larger than 100 percent for an ordinary branch-circuit design problem, you likely entered circular mils or length incorrectly.