Study guide
7.6 Equipment Grounding, Bonding, and Listing Markings
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
7.6 Equipment Grounding, Bonding, and Listing Markings
Key Takeaways Explain This Topic AI
Equipment grounding creates an effective fault-current path; bonding connects conductive parts so faults clear quickly.
Listing, labeling, and manufacturer instructions are enforceable installation constraints for devices and equipment.
Markings such as voltage, ampere rating, horsepower, temperature, wet-location suitability, and SCCR can decide the answer.
Neutral-to-case bonding errors, missing bonding jumpers, painted surfaces, and unsuitable replacement devices are common exam traps.
Last updated: May 2026
Grounding and bonding in equipment questions
Equipment and device questions often hide Article 250 inside ordinary-looking hardware. A receptacle, switch, luminaire, appliance, disconnect, raceway, box, motor frame, or HVAC cabinet can become energized during a fault. Equipment grounding and bonding provide the low-impedance fault-current path needed to open the overcurrent device. Without that path, metal parts can remain energized and dangerous.
Separate the terms:
- Term Meaning in exam logic
- Grounded conductor Normally carries current and is intentionally grounded, often the neutral
- Equipment grounding conductor Non-current-carrying fault-current path for equipment and metal parts
- Bonding Connecting metal parts to establish electrical continuity and fault-clearing ability
Grounding electrode conductor Connects the grounding electrode system to service or separately derived system grounding point
Effective ground-fault current path Intentionally constructed path capable of carrying fault current back to the source
The grounded conductor and equipment grounding conductor are not interchangeable downstream of the service disconnect or separately derived system bonding point. Many exam questions use appliance cords, subpanels, detached buildings, metal boxes, or replacement receptacles to test that separation.
Device grounding details
Receptacles with grounding contacts must have the grounding contact connected to an equipment grounding conductor or other permitted grounding path. Replacing a nongrounding-type receptacle with a grounding-type receptacle without a grounding path is not acceptable unless a specific permitted method, such as GFCI protection with required marking, is used. The marking matters because a GFCI can reduce shock risk but does not create an equipment grounding conductor.
Metal boxes and metal device covers must be bonded. Device yokes can be bonded by listed means, equipment bonding jumpers, self-grounding devices under permitted conditions, or contact with a properly grounded metal box when allowed. Paint, loose screws, improper adapters, and missing bonding jumpers can defeat the path.
Isolated grounding receptacles are another trap. An isolated grounding receptacle may have a separate insulated equipment grounding conductor for noise control, but it still must connect to the equipment grounding system. It is not an ungrounded receptacle, and it does not permit the equipment grounding path to float.
Listing and labeling
Listed or labeled equipment has been evaluated for specific uses. NEC installation rules require equipment to be installed and used according to instructions included in the listing or labeling. For exam purposes, listing instructions are not optional preferences. If a luminaire requires 90 C supply conductors, a dimmer requires compatible LED loads, or an HVAC unit has a maximum overcurrent device marking, those markings control the installation.
- Marking What it can decide
- Voltage and phase Whether equipment matches the circuit supply
- Ampere rating Branch-circuit and disconnect suitability
- Horsepower rating Motor switch or controller suitability
- Temperature rating Conductor insulation and terminal ampacity limits
- Wet, damp, weather resistant, raintight Location suitability
- SCCR Whether equipment can withstand available fault current where required
- Max lamp wattage Luminaire heat limits
A common wrong answer says to install equipment because the physical connection is possible. A 277 V switch on a 120 V circuit might be rated above voltage, but the load type still matters. A 30 A disconnect may not be sufficient for a motor load if it lacks the required horsepower rating. A receptacle that accepts a plug may still be the wrong voltage or ampere configuration.
Bonding around raceways and enclosures
Metal raceways and enclosures can be part of the equipment grounding path when installed properly. That means continuity through fittings, locknuts, bushings, connectors, couplings, and enclosures. Service raceways and concentric or eccentric knockouts can require special bonding attention. Reducing washers may be mechanically convenient but can raise bonding questions where fault-current reliability is critical.
Nonmetallic raceways generally require an equipment grounding conductor with the circuit conductors unless another rule applies. A PVC raceway does not provide a metal fault-current path. If a metal box is connected to PVC raceway, the box still must be bonded to the equipment grounding conductor.
Neutral-to-case and objectionable current
Appliances and equipment sometimes include bonding straps or screws. During service equipment installation or separately derived system bonding, a main bonding jumper intentionally connects grounded conductors to equipment grounding conductors at the permitted point. Downstream, that connection is generally removed or prohibited. Leaving a neutral bonding strap connected in a range, dryer, subpanel, or separately mounted enclosure can put normal neutral current on metal parts.
The exam may describe tingling on an appliance frame, current on a raceway, or a neutral connected to a panel cabinet in a subpanel. The answer is usually about objectionable current and improper bonding, not about needing a larger breaker.
Short-circuit current rating and equipment suitability
Some equipment must have a short-circuit current rating adequate for the available fault current. Industrial control panels, HVAC equipment, transfer switches, and service equipment may include SCCR markings. The journeyman exam may not require a full fault-current study, but it can ask what a marking means. SCCR is not the same as ampere rating. Ampere rating is normal current-carrying capacity; SCCR is withstand rating under fault conditions with specified protection.
Installation cases
Case 1: A two-slot receptacle is replaced with a three-slot receptacle on an old circuit with no equipment grounding conductor. If no grounding path exists, the replacement must follow the permitted ungrounded-receptacle replacement rules and marking. Simply installing a three-slot device creates a false ground indication.
Case 2: A metal luminaire canopy is attached to a plastic box with no equipment grounding conductor connected to the luminaire. If the luminaire has exposed metal parts requiring grounding, the installation fails.
Case 3: A subpanel in a detached building has neutrals and equipment grounds on the same bonded bar, while an equipment grounding conductor is run with the feeder. That is usually an improper neutral-to-case bond downstream of service equipment.
Exam traps
Do not say "ground" when the answer requires distinguishing grounded conductor, equipment grounding conductor, grounding electrode conductor, and bonding jumper. Do not assume GFCI protection creates an equipment grounding conductor. Do not ignore equipment markings. Do not treat a listed device as field-modifiable unless instructions permit it. Do not paint over bonding surfaces or rely on loose fittings. The exam is testing whether the fault path and listing conditions remain intact after installation.