Study guide

1.6 Using the Practice Bank, Error Log, and NEC Index

Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation and Source Control

1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index

2 Chapter 2: NEC Navigation, Definitions, and Code Strategy

2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab

3 Chapter 3: Electrical Theory and Calculation Foundations

3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab

4 Chapter 4: Services, Service Equipment, and Grounding/Bonding

4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab

5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing

5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab

6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables

6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab

7 Chapter 7: Equipment, Devices, Luminaires, and Controls

7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab

8 Chapter 8: Motors, Generators, Transformers, and Special Equipment

8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab

9 Chapter 9: Special Occupancies, Renewables, and Safety

9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab

10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs

10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook

11 Chapter 11: Final Review, Test Day, and License Planning

11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education

1.6 Using the Practice Bank, Error Log, and NEC Index

Key Takeaways Explain This Topic AI

Practice questions should train code navigation, calculation setup, and timing, not just answer recognition.

An error log should capture the missed concept, source route, reason for the miss, and next drill.

The NEC index is a scoring tool because it converts unfamiliar wording into article and table locations.

Mixed timed sets should be reviewed by domain so weak areas are repaired before full exam day.

Last updated: May 2026

Practice is a diagnostic tool

The local journeyman-electrician practice bank currently has 200 items. That is enough to reveal patterns, but only if you use the questions as diagnostics. A practice bank is not a set of answers to memorize. It is a way to test whether you can identify the topic, find the controlling reference, set up the calculation, and make a decision under time pressure.

Start with untimed topic sets only long enough to learn the article map. Then move to timed mixed sets quickly. The real exam is mixed, and the hardest part is often switching from branch circuits to services to motors to special occupancies without losing your place.

The four outputs of every practice question

Every question should produce one of four outcomes:

Outcome Meaning Next action

Correct and fast You knew the rule or route Keep it in rotation with mixed review.

Correct but slow You found it, but the path was weak Add an index drill or tab note.

Wrong concept You misunderstood the rule Reread the article section and write a summary.

Wrong process You knew the rule but made a setup or arithmetic error Build a calculation checklist.

This is why raw score alone is not enough. A 75% score with slow lookups may collapse under full-exam pacing. A 65% score with clear, fixable mistakes may improve quickly if the error log is honest.

Build an error log that changes behavior

An error log should be short enough that you will actually maintain it. Use one line per missed or slow question. The goal is to record the repair, not to rewrite the textbook.

Date Domain Miss type Source route Repair drill

2026-05-05 Wiring methods Used wrong fill table Chapter 9, raceway fill notes Do 5 raceway fill lookups with table headings.

2026-05-05 Branch circuits Missed continuous load factor Article 210 or 215 plus load rule Write setup before calculating.

2026-05-05 Motors Used nameplate instead of table FLC Article 430 tables and protection rule Drill 10 FLC table questions.

2026-05-05 Services Confused grounding and bonding terms Article 100, Article 250, Article 230 Build definition flashcards with article route.

Use standard miss types:

source : used the wrong book, edition, article, table, or note.

definition : missed a term that Article 100 or an article-specific definition controls.

condition : ignored a key fact such as dwelling, continuous load, wet location, or number of conductors.

calculation : used the wrong formula, factor, or base value.

time : found the answer but too slowly.

reading : answered a question the exam did not ask.

NEC index drills

The NEC index is not just the back of the book. It is a translation tool. Exam questions may use field language, formal code language, or a mixture. The index helps convert the clue into a location.

Try this drill for 15 minutes:

Pick 10 practice questions you missed or flagged.

Circle the strongest noun or phrase in each question.

Look up that term in the NEC index without reading the answer explanation.

Write the article or table route.

Compare your route to the explanation.

Add one tab or margin note only if it would have saved time.

Example conversions:

  • Question wording Index or article clue Likely route
  • receptacle spacing in a dwelling room receptacles, dwelling units Article 210
  • service disconnect location services, disconnecting means Article 230
  • conductor ampacity in a raceway ampacity, conductors Article 310 and Chapter 9 if fill applies
  • motor branch-circuit short-circuit protection motors, protection Article 430
  • hazardous classified location wiring method hazardous locations Chapter 5 articles
  • Calculation checklist

Electrical exam calculations fail when the candidate starts arithmetic too early. Before using the calculator, write the setup mentally or on allowed testing material.

Checklist:

What is the final quantity: amperes, VA, conductor size, raceway size, overcurrent rating, or number of boxes?

Is the system single-phase or three-phase?

Is the load continuous, noncontinuous, dwelling, motor, feeder, service, or branch circuit?

Which article controls the base rule?

Which table supplies the base value?

Are correction or adjustment factors required?

Does an exception or note change the answer?

Are the answer choices rounded in a way the NEC permits?

Core setups:

  • amperes = watts / volts
  • three-phase amperes = VA / (volts x 1.732)
  • minimum ampacity = load x required percentage
  • final ampacity = table ampacity x correction x adjustment
  • Timed set progression

Use a progression instead of jumping from chapter reading to a full exam.

Stage Set size Time target Purpose

Topic drill 10 questions 20 to 30 minutes Learn one article family.

Mixed mini-set 20 questions 60 minutes Practice switching domains.

Half exam 40 questions 120 minutes Test endurance and pacing.

Full exam 80 questions 240 minutes Rehearse the real format.

After each set, spend at least half as much time reviewing as you spent answering. Review is where the score is built. If you take 60 minutes on a mixed set, spend 30 minutes with the NEC open, updating the error log and drilling routes.

Use bank counts without being trapped by them

The local bank has many definition questions and only one control-devices question. That does not mean the real exam has the same distribution. The ICC outline gives Control Devices 4%, which is roughly 3 questions on an 80-question form. If the bank is thin in a domain, create your own lookup drills from the NEC articles and tables.

For definitions, do not memorize isolated words only. Connect each definition to a work example. For example, bonding, grounded conductor, equipment grounding conductor, and grounding electrode conductor are not interchangeable. A wrong definition can send you to the wrong Article 250 rule and cost multiple questions.

Final-week routine

In the final week, stop collecting new material unless it fixes a known gap. Your job is to stabilize process.

Take two timed mixed sets and one full 80-question rehearsal.

Review every missed or slow item in the error log.

Redo all calculation misses without looking at the explanation first.

Run NEC index drills for your 20 weakest terms.

Check current ICC and jurisdiction instructions before exam day.

Confirm your approved references, tabs, notes, identification, calculator, and appointment details.

The best sign of readiness is not that every topic feels easy. It is that you know what to do when a question feels unfamiliar: identify the domain, find the source route, check the condition, do the setup, and move on before the clock takes over.