Study guide
5.3 Conductor Ampacity, Temperature, and Terminal Ratings
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
5.3 Conductor Ampacity, Temperature, and Terminal Ratings
Key Takeaways Explain This Topic AI
Ampacity selection starts with conductor material, insulation temperature rating, wiring method, and table conditions.
Terminal temperature limitations often control the final allowable ampacity even when insulation has a higher rating.
The 90 C column is commonly used as a starting point for adjustment and correction, not as automatic permission to terminate at 90 C ampacity.
Equipment rated 100 A or less or conductors 1 AWG and smaller commonly require 60 C termination ampacity unless listed otherwise.
Last updated: May 2026
Ampacity is not one lookup
Ampacity is the current a conductor can carry continuously under stated conditions without exceeding its temperature rating. NEC ampacity tables are based on assumptions such as ambient temperature, number of current-carrying conductors, conductor material, insulation type, and wiring method. When the actual installation differs from the table conditions, adjustment or correction may be required.
The exam rarely rewards a one-step lookup. You usually need a workflow. First identify copper or aluminum. Then identify insulation, such as THHN, THWN, XHHW, or USE. Next identify the wiring method and whether the conductor is in a raceway, cable, earth, free air, or equipment. Then select the correct ampacity table. For common conductors in raceway or cable, candidates often use the familiar table in Article 310.
Temperature-column logic
Column Typical use in exam setup Warning
60 C Small equipment terminations, many devices, conductors 1 AWG and smaller unless listed otherwise Often controls final ampacity
75 C Larger equipment or equipment listed for 75 C terminations Common for feeders with listed lugs
90 C Conductors with 90 C insulation such as THHN Often used for adjustment and correction starting ampacity only
Terminal ratings matter because heat at a termination can damage equipment. A conductor with 90 C insulation may be installed on equipment whose terminals are rated only 60 C. In that case, the final selected conductor must be adequate under the terminal limitation. You may use the 90 C ampacity for adjustment and correction if the conductor insulation permits, but the final result cannot exceed what the termination allows.
Basic workflow
Determine calculated load or required circuit rating.
Identify conductor material and insulation temperature rating.
Identify the ampacity table and base ampacity.
Apply ambient temperature correction if needed.
Apply adjustment for more than three current-carrying conductors if needed.
Compare the adjusted ampacity to the load.
Check terminal temperature limitation for the final conductor size.
Check overcurrent protection and any small-conductor or equipment-specific rule.
Worked setup: 70 A feeder with copper THHN
Assume a 70 A noncontinuous feeder load, copper THHN conductors in raceway, normal ambient, three current-carrying conductors, and equipment with 75 C terminals. Because there are no derating factors in this simplified setup, look to the copper ampacity table. The conductor insulation is 90 C, but the terminals are 75 C. The final conductor must have at least 70 A in the 75 C column.
If 4 AWG copper is rated 85 A in the 75 C column, it can satisfy the 70 A ampacity requirement before considering other conditions. The 90 C value is not needed because there is no adjustment or correction in the setup. If the same conductors were on 60 C terminals, you would check the 60 C column instead.
Worked setup: derating with 90 C insulation
Assume eight current-carrying 12 AWG copper THHN conductors are in one raceway at normal ambient. The conductor has 90 C insulation, so adjustment can start from the 90 C ampacity. If the applicable adjustment factor is 70 percent for the number of current-carrying conductors, and the 90 C ampacity is 30 A, the adjusted ampacity is:
30 A x 0.70 = 21 A
Now compare that result with the circuit needs and terminal limits. For a 20 A branch circuit, 21 A adjusted ampacity is enough before considering any other rule. But the conductor still terminates on devices that may be limited to 60 C. The 60 C ampacity for 12 AWG copper is normally 20 A, so the 20 A circuit can still work if all other rules are satisfied.
Equipment markings and listed instructions
The NEC often points you back to listed equipment markings. A lug may be marked CU only, AL only, CU/AL, 60 C, 75 C, or with a conductor range. You cannot fix a wrong termination by choosing a larger conductor if the lug is not listed for that conductor material or size. Exam questions may hide this in the wording: "terminals marked 75 C," "equipment rated 100 A or less," or "conductors are 1 AWG copper."
When equipment is rated 100 A or less or uses conductors 1 AWG and smaller, 60 C ampacity is commonly the default termination limit unless the equipment is listed and marked otherwise. For equipment over 100 A or conductors larger than 1 AWG, 75 C is commonly used where listed. Always follow the exact NEC edition and equipment markings stated in the question.
Exam traps
The most common trap is selecting a conductor only from the 90 C column because the insulation says THHN. That is incomplete. THHN may allow a 90 C derating starting point, but final ampacity must still respect terminal limits.
Another trap is adjusting from the wrong column. If the conductor insulation is only 75 C, do not start adjustment from a 90 C value. If the conductor is 90 C rated but the equipment terminals are 75 C, you may be able to start adjustment from 90 C and then verify that the chosen conductor is also acceptable at 75 C termination ampacity.
A third trap is forgetting that neutral conductors may or may not count as current-carrying conductors for adjustment. That topic belongs in the next section, but it affects the same ampacity workflow. Do not count raceway fill and ampacity adjustment the same way; they are different rules with different tables.
For study, practice writing the workflow in the margin of your code book. The open-book exam is timed, and candidates will not have time to rediscover the sequence on every item. Your advantage is knowing what to check and what not to check.