Study guide
5.5 Overcurrent Protection and Small-Conductor Rules
Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation and Source Control
1.1 ICC R17, T17, G17, and Jurisdiction Variance 1.2 Current Format, Cost, Time, and Passing Score 1.3 Licensing Board vs. Exam Provider 1.4 Official References, Open-Book Rules, and Calculators 1.5 Domain Weights and Study Map 1.6 Using the Practice Bank, Error Log, and NEC Index
2 Chapter 2: NEC Navigation, Definitions, and Code Strategy
2.1 NEC Book Structure and Article Map 2.2 Article 100 Definitions and Exam Language 2.3 Index, Table, and Annex Navigation 2.4 Shall, Shall Not, Permitted, and Informational Notes 2.5 Using Code References Without Overlooking Context 2.6 State Amendments and Code Edition Control 2.7 NEC Navigation Case Lab
3 Chapter 3: Electrical Theory and Calculation Foundations
3.1 Ohm's Law, Power, and Basic Units 3.2 Series, Parallel, and Circuit Behavior 3.3 Single-Phase, Three-Phase, and Voltage Systems 3.4 Continuous Loads, Demand, and 125 Percent Rules 3.5 Voltage Drop and Practical Calculation Setup 3.6 Load Calculation Workflow 3.7 Calculation Foundation Case Lab
4 Chapter 4: Services, Service Equipment, and Grounding/Bonding
4.1 Service Point, Service Conductors, and Disconnects 4.2 Service Load Calculation and Sizing 4.3 Service Equipment, Panelboards, and Switchboards 4.4 Grounding Electrode System and GEC 4.5 Bonding, Main Bonding Jumpers, and Effective Fault Path 4.6 Transformers and Separately Derived Systems 4.7 Services and Grounding Case Lab
5 Chapter 5: Feeders, Branch Circuits, and Conductor Sizing
5.1 Feeder vs. Branch Circuit Boundaries 5.2 Branch Circuit Ratings and Required Outlets 5.3 Conductor Ampacity, Temperature, and Terminal Ratings 5.4 Adjustment, Correction, and More Than Three Conductors 5.5 Overcurrent Protection and Small-Conductor Rules 5.6 GFCI, AFCI, Equipment Grounding, and Dwelling Circuits 5.7 Feeders and Branch Circuits Case Lab
6 Chapter 6: Wiring Methods, Raceways, Boxes, and Cables
6.1 Raceway Selection and Installation Logic 6.2 Underground Wiring, Wet Locations, and Protection 6.3 Boxes, Enclosures, and Conduit Bodies 6.4 Box Fill, Conductor Counting, and Device Yokes 6.5 Cabinets, Panelboards, and Switchboards 6.6 Flexible Cords, Cables, and Temporary Wiring 6.7 Wiring Methods Case Lab
7 Chapter 7: Equipment, Devices, Luminaires, and Controls
7.1 Receptacles, Switches, and Device Selection 7.2 Luminaires, Lampholders, and Lighting Outlets 7.3 Appliances and Utilization Equipment 7.4 Heating, Cooling, and HVAC Electrical Connections 7.5 Disconnects, Controllers, and Switching Devices 7.6 Equipment Grounding, Bonding, and Listing Markings 7.7 Equipment and Devices Case Lab
8 Chapter 8: Motors, Generators, Transformers, and Special Equipment
8.1 Motor Circuit Anatomy and Article 430 Navigation 8.2 Motor Conductors, Overload, and Short-Circuit Protection 8.3 Motor Controllers, Disconnects, and Nameplates 8.4 Generators, Transfer Equipment, and Optional Standby 8.5 Transformer Sizing, Protection, and Grounding 8.6 Emergency Systems, Fire Alarms, and Signaling Overview 8.7 Motors and Generators Case Lab
9 Chapter 9: Special Occupancies, Renewables, and Safety
9.1 Hazardous Classified Locations 9.2 Healthcare, Marinas, RV Parks, and Mobile Home Parks 9.3 Pools, Spas, and Similar Installations 9.4 Solar PV, Energy Storage, and Renewable Systems 9.5 Temporary Power, Emergency Systems, and Special Conditions 9.6 OSHA Subpart K and Safe Work Practice Context 9.7 Special Occupancies Case Lab
10 Chapter 10: Open-Book Exam Workflow and Mixed Code Labs
10.1 Four-Hour Pacing and Question Triage 10.2 Look-Up vs. Know-From-Memory Decisions 10.3 Mixed Calculation Lab 10.4 Mixed Code Navigation Lab 10.5 Diagnostic Report and Error Log Remediation 10.6 High-Weight Domain Remediation Plan 10.7 Full Exam Simulation Playbook
11 Chapter 11: Final Review, Test Day, and License Planning
11.1 Final Two-Week Study Plan 11.2 Reference Book, Tabs, and Allowed Materials Checklist 11.3 Pearson VUE, PRONTO, and Test-Day Rules 11.4 After the Exam: Results, Retakes, and Challenges 11.5 License Application, Work Hours, and Jurisdiction Next Steps 11.6 After Journeyman: Master, Contractor, and Continuing Education
5.5 Overcurrent Protection and Small-Conductor Rules
Key Takeaways Explain This Topic AI
Conductors must generally be protected against overcurrent based on their allowable ampacity after required calculations.
The standard overcurrent ratings rule can permit moving up to the next standard size only when all conditions are met.
Small-conductor rules limit overcurrent protection for 14, 12, and 10 AWG copper conductors unless a specific exception applies.
Equipment articles can require smaller or larger overcurrent devices than a simple conductor ampacity lookup suggests.
Last updated: May 2026
Protection follows the conductor and the equipment
Overcurrent protective devices protect conductors and equipment from excessive current. For branch circuits and feeders, you generally size conductors for the load, then choose overcurrent protection that does not exceed the conductor ampacity unless a rule permits it. Article 240 is central, but it often works with Articles 210, 215, 220, 310, 422, 430, 440, and 450.
An exam problem may offer breaker sizes that are all standard ratings. Your task is to decide which standard rating is legal for the selected conductor and load. Do not assume the next larger breaker is always permitted. Do not assume the conductor ampacity alone controls when a motor, air conditioner, transformer, welder, or appliance article gives special rules.
Standard ratings and next size up
NEC standard ampere ratings for fuses and inverse-time circuit breakers appear in Article 240. If the calculated conductor ampacity falls between standard overcurrent sizes, the next higher standard rating may be permitted only under specific conditions. Common conditions include that the conductors are not part of a multioutlet receptacle circuit for cord-and-plug portable loads and that the next standard size does not exceed a stated ceiling.
Example setup: A feeder conductor has an allowable ampacity of 76 A after all adjustment, correction, and terminal checks. Standard overcurrent ratings include 70 A and 80 A. If all next-size-up conditions are satisfied, an 80 A overcurrent device may be allowed. If a condition is not satisfied, the answer may be 70 A or a larger conductor.
Small-conductor rule
The small-conductor rule is high-yield. Unless a specific rule permits otherwise, copper conductors are commonly limited as follows:
- Copper conductor General small-conductor OCP limit
- 14 AWG 15 A
- 12 AWG 20 A
- 10 AWG 30 A
For aluminum and copper-clad aluminum, the corresponding small-conductor limits are lower for the same AWG sizes where applicable. The exam often gives THHN insulation and asks whether 12 AWG copper can be protected at more than 20 A because its 90 C table ampacity is higher. The answer is usually no for ordinary branch circuits. The small-conductor rule stops that shortcut.
Worked setup: 12 AWG copper THHN
A question says 12 AWG copper THHN conductors are installed in a raceway for a general-purpose branch circuit with 60 C terminations. The 90 C ampacity can be useful for derating, but ordinary 12 AWG copper branch-circuit conductors are generally protected at not more than 20 A unless a specific exception or equipment article applies.
If there are eight current-carrying conductors and the adjusted ampacity from the 90 C column is 21 A, a 20 A breaker can be acceptable from the ampacity side. A 25 A breaker is not justified simply because 21 A is above 20 A or because the 90 C table value is 30 A. The small-conductor rule controls.
Worked setup: continuous load and OCP
A branch circuit supplies 24 A of continuous load only. The minimum branch-circuit rating is:
1.25 x 24 A = 30 A
A 30 A circuit could satisfy the continuous-load sizing step if conductors and terminals are adequate. For copper conductors, 10 AWG often appears because of the 30 A small-conductor limit. If the answer choices include 12 AWG copper on a 30 A breaker for an ordinary load, that is a trap.
Equipment-specific rules
Motors are the classic exception area. Motor branch-circuit short-circuit and ground-fault protective devices may be much larger than the conductor ampacity because overload protection is handled separately. Air-conditioning and refrigeration equipment can use nameplate minimum circuit ampacity and maximum overcurrent protective device values. Transformers have primary and secondary protection rules. Fixed appliances may have branch-circuit limits in Article 422.
When a question involves equipment with a nameplate, use the nameplate values if the NEC article directs you to do so. For HVAC equipment, "minimum circuit ampacity" is a conductor-sizing value and "maximum overcurrent protective device" is an overcurrent ceiling. Do not replace those marked values with a general lighting branch-circuit habit.
Exam traps
One trap is applying next-size-up permission before completing derating and terminal checks. First determine allowable ampacity. Then decide whether the next standard rating rule is available. The rule does not repair a conductor that is too small for the calculated load.
Another trap is using the 90 C column to protect small conductors at a higher breaker size. For ordinary circuits, 14, 12, and 10 AWG copper have familiar protection limits. Higher insulation ratings do not erase those limits.
A third trap is treating all overcurrent devices as overload protection. In motor and HVAC circuits, one device may protect against short circuit and ground fault while another protects against overload. The NEC separates those functions, and the exam will test the separation.
Fast decision table
- Question asks First article family to check
- General conductor protection 240 and 310
- Branch-circuit rating 210
- Feeder minimum rating 215 and 220
- Motor circuit breaker size 430
- Air-conditioning equipment breaker 440 and nameplate
- Appliance branch circuit 422
Use the general rule only when no more specific rule applies. The NEC structure matters: general rules establish the baseline, but equipment articles modify the answer when their scope fits the installation.